Kohler K-98155X Istruzioni per il montaggio

Installation and Care Guide

Freestanding BubbleMassage Bath





K-98155X

1204153-X2-A 2 Kohler Co.

Thank You for Choosing Kohler Company

Important Information

IMPORTANT SAFETY INSTRUCTIONS

Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all operating and safety instructions.

NOTE: The bathtub pictured in the installation steps may dier from the model being installed.

IMPORTANT NOTICE TO INSTALLERS!: Please leave these instructions for the consumer. They contain

important information.

In addition to installation procedures, this manual contains important care and cleaning. Please retain for future

reference.

¨ Please provide adequate available space for the bath unit in accordance with rough-in. Arrange the location of

drain in advance.

¨ Identify blower and switch access location before proceeding with installation.

¨ Bath can be installed aer the wall is completed. Bath drain supplies should be arranged preliminarily

according to the selected bath.

NOTICE: DO NOT LIFT BATH BY PIPE WORK. Inspect for any possible damage that may have occurred in

transit. Position a clean drop cloth or similar material in the boom of the bath to pretect the nish. Be careful not

to scratch the surface of the bath.

Thank you for choosing Kohler. Kohler crasmanship oers you a rare combination of proven performance

and graceful sophistication that will satisfy you for years to come. The dependability and beauty of your Kohler

product will surpass your highest expectations. We’re very proud of our products here at Kohler and we know

you will be too.

Please take a few minutes to review this manual before you start installation. If you encounter any installation

or performance problems, please don’t hesitate to contact us. Our phone numbers and website are listed on back

cover.

All information in this manual is based upon the latest product information available at the time of publication.

At Kohler, we constantly strive to improve the quality of our products. We reserve the right to make changes in

product characteristics, packaging or availability at any time without notice.

Thank you for choosing Kohler Company.

WARNING: Risk of electrical shock. A licensed electrician should make all electrical connections.

DANGER: Risk of re, electric shock, or injury to Persons. Read important safety instructions

included in these instructions.

WARNING: Risk of electrical shock. Connect only to a circuit protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

WARNING: Risk of electrical shock. Disconnect power before servicing.

A. Installation Hazard Notication

Read and Practice the Instructions Strictly

Kohler Co. 3 1204153-X2-A

Product Requirements

A. Summary of Key Requirements

¨Observe all local plumbing and electrical codes.

¨Install the unit to a level suboor.

¨Provide properly-dimensioned framing.

B. Plumbing Specications

If using a rim-mounted bath faucet, exible connections between the valves and spout may be required. Conrm

adequate mounting, connection space of specied faucet for your installation.

C. Product Inspection

Carefully unpack and inspect the bath with airjets for damage. Leave all materials in the carton during

constructions to prevent damage.

D. Electrical Requirements

The installation must have a Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

The GFCI or ELCB protects against Line-to ground shock hazard. Use a 220-240 V, 10 A (minimum), 50 Hz

dedicated service for the bath with airjets.

NOTICE: Follow all local plumbing and electrical codes.

ATTENTION: Temperature deviation. Water temperature at dierent parts of the bath may not be the same,

which may cause the temperature detected and shown on the panel slightly dier from the actual water

temperature in the bath.

WARNING: Keep the area around the blower motor clean and free of debris. Ensure that the area

around the blower motor is free of sawdust, insulation, dirt, or other small loose debris. Such material

could clog the blower motor air ducts and reduce the air ow through the blower.

WARNING: Risk of damp. Silicone sealant shall be applied to connections of the bath drain pipe and the

drainage pipeline.

WARNING: Unauthorized modication may cause unsafe operation or aect performance of the bath

with airjets. Do not relocate the blower motor, or make other modications to the system in the absence

of kit instructions, as this could adversely aect the performance and safe operation of the bath with

airjets. Kohler shall not be liable under its warranty or otherwise for personal injury or damage caused by

any such unauthorized modication.

B. Factory-Assembled Features

Factory installed components include blower motor with power supply cord, electronic drain, controller, check

valve, air piping, water level sensor, user keypad, and keypad cable. Other than power wiring and plumbing,

no assembly is needed.

Important Safety Instructions (Cont.)

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following Product Requirements.

1204153-X2-A 4 Kohler Co.

Tools

Site Requirements

Plus:

¨ Plumbers puy

¨ Wall coverings (if necessary)

¨ Gypsum cement (optional)

¨Construction adhesive or silicone

(optional)

¨ Protective covering for bathtub

¨Nails

¨Conventional woodworking or

concrete installation tools and materials

¨Drop cloth

NOTICE: Unless otherwise specied, oor support under the bath must provide for a minimum of 390 kg/

square meter loading.

¨ Make sure the ooring oers adequate support for your bath, and verify that the suboor is at and level.

CAUTION: Risk of product damage. Do not support the bath by the rim.

CAUTION: Risk of product damage. Do not li the bath with airjets by the air channels or blower

motor, or use the air channels or blower motor for structural support of the bath.

CAUTION: Risk of product damage. Do not support the bath by the rim.

¨ Your new bubble has been manufactured to the highest possible standards, it has been factory tested and

approved.

¨ When removing bath from protective carton . DO NOT LIFT BATH BY PIPE WORK. Inspect for any possible

damage that may have occurred in transit. Position a clean drop cloth or similar material in the boom of the

bath to pretect the nish. Be careful not to scratch the surface of the bath.

IMPORTANT: Bath must be installed level on all top edges.

Installation

Before Installing the Bath

¨ Unpack bath shell and skirt and check for any transit damage prior to installation.

¨ Position the bath shell in the desired location in the bathroom.

¨ Check that the plumbing can be connected to the bath when in the desired location.

A. Install the Bath

Kohler Co. 5 1204153-X2-A

¨ The drain has been installed onto the bath before it leaves factory. Fill the bath with water before the bath

is securely positioned so as to check the connections for leaks.

¨ Ensure a seal on the bath drain and the oor drain.

NOTE: Be careful not to damage the boom of the bath and the suboor.

C. Put the bath at desired position

¨ Adjust feet height.

¨ Adjust the four feet to 48 mm lower than the apron and keep the feet in the same plane.

B. Check Plumbing

CAUTION: Risk of product damage. Ensure a watertight seal on the bath drain.

Installation (Cont.)

¨ Up stand bathtub, slide feet to the bath xed position, check all clips in the same direction; locate center lines

as drawing (according to the line on the ground, line on the bathtub rim by square).

¨ Ensure the adequate space for the bath sliding from the feet. Check and insure the clip direction to making the

bath slide in and out in the same way.

¨ Remove the bathtub; fasten the feet clip to the oor by using the screws aached in the package. Every clip

fastened by 2 screws in the diagonal.

¨ Adjust the nut on the feet, making the nut lower 2-3 mm than the clip.

¨ Readjust the feet height, making the feet lower 5 mm than the apron.

Screw Out

1204153-X2-A 6 Kohler Co.

D. How To Use The Pillow

¨ Clean and dry the bracket and PU elastomer pillow. Fix the PU elastomer pillow onto the bracket (PU

elastomer pillow is about 2mm longer than the bracket in every side).

¨ Press down the bracket buon and adjust the pillow to a proper angle, recommend for three adjust angles.

In case the bracket buon is loose, please tighten it.

¨ Upli the bath and the apron, and then connect the drain pipe.

¨ Incorporate the lines on the bath and the oor, slide the bathtub to the feet clip, if the bath loosely connected

to the clip, remove the bath and adjust the nut to fasten the bath to the clip.

Installation (Cont.)

Button

Pillow Bracket

Pillow

Kohler Co. 7 1204153-X2-A

E. How To Remove The Pillow Bracket

¨ Loosen the inner hexagon screw on the boom of the pillow bracket, and then remove the pillow form the

bath.

G. Make Electrical Connections

F. How To Remove The Grip Rail (Optional)

¨ Loosen the inner hexagon screw on the boom of the grip rail, and then remove the grip rail form the bath.

Installation (Cont.)

Inner Hexagon Screw

WARNING: Risk of electric shock. To reduce the risk of electrical shock, connect the control box to

a properly grounded, grounding-type receptacle protected by Ground-Fault Circuit-Interrupters (GFCI ‘s).

Do not remove the plug grounding pins. Do not use grounding adapters.

NOTE: Electronic parameter label located on the controller. This label also identies the electrical rating.

¨ Your Kohler bath with airjets is equipped with a cord and plug. The blower motor has been wired at the

factory. A licensed electrician must install a dedicated GFCI-protected, 220 V, 10 A, grounded outlet.

¨ Plug the control box into this outlet.

¨ Clean the area of all dust and debris.

H. Test Run the Bath with Airjets

¨ Check all electrical connections, and make sure the electrical power to the bath with airjets is on.

¨Make sure all piping connections in the air harness are secure.

¨ Verify that the blower motor is secure.

¨ Temporarily remove the plastic drop cloth or other protective sheeting from the bath.

1204153-X2-A 8 Kohler Co.

NOTE: Please read these steps carefully before you operate your bath with airjets. Troubleshoot any problems

using the “Troubleshooting” section.

NOTE: Please do not use the bath in case of outage. In this case, the electronic drain automatically opens and the

bath can not be lled with water.

A. Fill the Bath

Installation (Cont.)

CAUTION: Risk of product damage. Ensure that the area around the blower motor is free of sawdust,

insulation, dirt, or other small loose debris. Such material could clog the blower motor air ducts and

reduce the air ow through the blower motor.

Bath Operation

I. Drilling And Cutting Acrylic

DRILLING: Small holes can be drilled with a twist drill, but the cuing edge MUST be backed o with an oil

stone (the sharp edge dulled). Large holes must be drilled with a hole saw. Maximum drill size-12mm. Drill

speeds-6mm x 1800 RPM-12 mm x 900 RPM.

NOTE: Always drill from acrylic surface.

CUTTING: If for any reason the acrylic requires cuing, use a ne tooth hacksaw and proceed with caution.

Edges can be smoothed with a second-cut le and medium-ne sandpaper. If the surface of the acrylic should

happen to be damaged, it can be restored by polishing with an abrasive cleaner. Deep scratches can be removed

by rubbing with 600 grade wet & dry sandpaper then polishing.

J. Clean-Up After Installation

¨ Clean the area around the blower motor of all dust and debris.

¨ Use warm water and a liquid detergent to clean the surface of the bath with airjets. Do not use abrasive

cleansers, as they may scratch and dull the surface. Do not use powdered cleaners unless the cleaner is fully

dissolved in water. Solid substances could block the airjets. Do not use bleach or ammonia cleaning solutions.

Chemically active cleaning solutions can damage the bath surface. Refer to the homeowners guide for normal

cleaning recommendations.

¨ Slide the sliding slip to unlock the panel. Touch the electronic drain on/o buon “ “ to close the drain.

The pink light ashes. Fill the bath to a level at least 10 cm above the top of the highest airjet.

¨ Refer to “Bath Operation” to make sure that every function works well.

¨Check the drain piping for leaks. Repair any leaks.

¨ Operate the bath and check for air ow through the airjets. Check the air piping for air leaks.

¨ Stop the bubble massage and drain the water.

¨ Return the plastic drop cloth or other protective sheeting to the bath. Check the drain connections for leakage.

Manual Purge Electronic Drain On/Off Pump On/Off

Water Temperature Decreases/Increases Flow

Kohler Co. 9 1204153-X2-A

Bath Operation (Cont.)

¨ When the nger is within 1-3 cm to the panel, lights on the sliding slip will ash one by one along “ “

direction. Slide along “ “ direction, the panel will be unlocked and activated.

¨ If the panel is not operated within 30 seconds (no drops of water splash into the sensing range of the panel),

it will be automatically locked and enter energy-saving mode with no light display.

Function Operation

NOTE: Before operating the panel, please conrm that there is no obvious water stains on the panel. If there is

any, please rst wipe it clean.

Electronic Drain

Slide the sliding slip to unlock the panel. Start the drain by touching the buon “ “ once, the green light

ashes. Touch again to stop it ,the pink light ashes. When touching this buon, a slight sound can be heard from

the drain at the boom of the bath.

Bubble Massage

Slide the sliding slip to unlock the panel. Touch the buon “ “ to start the blower motor, blue light ashes.

Touch again to stop it, blue light half ashes.

Touch the buon “ “ The blower motor will automatically stop aer running for about 20 minutes.

Bubble Adjustment

Slide the sliding slip to unlock the panel. When the blower motor is running, slide in “ “ direction to increase

the air ow and the light gradually ashes from white to blue as the nger moves along “ “ direction.

Slide in “ “ direction to decrease the air ow, the light gradually dies out from blue to white as the nger

moves along “ “ direction. When air ow reaches its maximum, all the blue light will ash. When air ow

reaches its minimum, only the white light will ash.

Manual Cleaning

Slide the sliding slip to unlock the panel. Start the blower motor by touching the buon “ “ the orange light

ashes. It will automatically stop aer running for about 2 minutes.

Automatic Cleaning

Aer running for 20 minutes, BubbleMassage will automatically turn o. Press electronic drain on/o buon to

open the drain. When water level drops below airjet holes, auto cleaning will activate for 2 minutes.

B. Keypad Operation

Manual Purge Electronic Drain On/Off Pump On/Off

Water Temperature Decreases/Increases Flow

1204153-X2-A 10 Kohler Co.

Bath Operation (Cont.)

Panel Function

1. Power Off (No Display)

2. Power On

4. Blower Open

3. Light Change to Stand by Situation

Blue-Orange-Red Orange Green Blue White-Blue

50% Blue WhitePink

Water Temperature

(Light depend on water temperature)

Water Temperature

(Blue-Orange-Red)

Drain Close

(Pink)

BBM Open

(Blue)

Adjust the Strength of BBM

(White-Blue)

Indice

Lingue:

Altri manuali Kohler Vasca

Kohler

Kohler PRELUDE K-8266T Manuale utente

Kohler

Kohler K-1122-GLA Guida rapida

Kohler

Kohler K-1227 Guida rapida

Kohler

Kohler K-1151 Manuale utente

Kohler

Kohler K-8331T Series Istruzioni per il montaggio

Kohler

Kohler K-1201-HB Guida rapida

Kohler

Kohler K-1368-H2 Istruzioni per il montaggio

Kohler

Kohler K-45600X Istruzioni per il montaggio

Kohler

Kohler K-1257-LA Guida rapida

Kohler

Kohler Windward K-1115-LA Guida rapida

Kohler

Kohler Underscore K-1822-GVB Manuale utente

Kohler

Kohler K-941 Istruzioni per il montaggio

Kohler

Kohler BIOVE K-8277T-GR Manuale utente

Kohler

Kohler K-1239P-LA Guida rapida

Kohler

Kohler K-1112-HL Guida rapida

Kohler

Kohler K-1418-HC Istruzioni per il montaggio

Kohler

Kohler K-1148 Guida rapida

Kohler

Kohler Stargaze K-24019-GHW Manuale utente

Kohler

Kohler K-1107 Manuale utente

Kohler

Kohler K-1246 Guida rapida

Kohler

Kohler K-856-M Istruzioni per il montaggio

Kohler

Kohler K-1112-CB Guida rapida

Kohler

Kohler VINTAGE K-700 Manuale utente

Kohler

Kohler K-12345M Istruzioni per il montaggio

Manuali Vasca popolari di altre marche

Agua

Agua BARTOLI-66 Manuale utente

PAA

PAA PRELUDE Manuale utente

BETTE

BETTE SILHOUETTE Manuale utente

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manuale utente

Oliveri

Oliveri Naples Manuale utente

Lyons

Lyons Elite ETLxx663219 Series Manuale utente

Woodbridge

Woodbridge BJ500 Istruzioni per il montaggio

Whirlpool

Whirlpool Ariel ARL-702 Manuale utente

TEIKO

TEIKO EXCELLENT DUO Manuale utente

American Standard

American Standard Colony 5-1/2' x 32" Manuale utente

American Standard

American Standard 3052OD.X0X Guida rapida

agape

agape MARSIGLIA AVAS1075 Manuale utente

Kallista

Kallista P50045-G5 Istruzioni per il montaggio

Ariel

Ariel AM Series Manuale utente

Agua

Agua BAHLI-60 Manuale utente

DURAVIT

DURAVIT XViu 700443 Manuale utente

American Standard

American Standard Colony 2740 Series Manuale utente

Rapsel

Rapsel OFURO Manuale