Korenix JetNet 5628G Series Manuale utente
JetNet 5628G/5828G/5628G-R/5828G-R
IEC 61850-3 Modular Managed Ethernet Switch
Quick Installation Guide
www.korenix.com
V1.1
Introduction
The JetNet 5628G/5828G is a 19-inch 1U High Industrial 24+4G Modular Managed Ethernet
Switch, equipped with 3 slots for maximum 24 10/100 Base-TX Ports or 18 100Base-
FX Fiber interfaces ports plus 4 Gigabit RJ45 / MINI GBIC combo ports. The JetNet
5628G/5828G, a special design for substation automation and industrial control room, is
FRPSOLDQWZLWKWKH,(&,(((KLJKOHYHOHQYLURQPHQWDOFHUWL¿FDWLRQV7KHVZLWFK
also supports Jumbo Frame forwarding of up to 9.2Kbytes. With this, the transmission of
ODUJH¿OHVEHFRPHVPRUHHI¿FLHQWDQGVROLG7RIXO¿OOWKHDGYDQFHGPDQDJHPHQWFRQWURO
and security requirements in power substations and control rooms, the JetNet 5628G/5828G
supports various software features. The VLAN, MSR, RSTP, QoS, IGMP, ACL, 802.1x, DHCP
Option 82, SNMP, LLDP, etc. complete the demand and greatly satisfy technicians’ requests.
The JetNet 5828G has the same hardware design as JetNet 5628G, however in addition, the
JetNet 5828G supports Layer 3 switching/routing features. The JetNet 5628G-R/5828G-R
is an extended product line designed with Ethernet ports on the rear panel. All the Fast
Ethernet modules are accepted by the JetNet 5628G/5828G series.
8QSDFNWKHER[\RXZLOO¿QG
The Rack Mount Managed Ethernet Switch (4GT Combo, no module inside)
RS-232 DB9 (Null-Modem) console cable
Rack Mount kit
Power Cord (Depend on Country)
2. Interface Introduction(JetNet 5628G/5828G)
2.1 LED:
Hardware Installation
System LED
PWR 1, PWR 2 (AC/ HDC)
DC 1, DC 2 (LDC Power)
RDY (System Ready)
DI 1, DI 2 (Digital Input)
R.M. (Ring Master)
DO 1, DO 2 (Digital Output)
R.F. (Ring Failure)
Port LED
Port 1~8 (JNM5-8TX)
Port 1~8 (JNM5-4TX/4SFP)
Port 1~6 (JNM5-2SFP/4MSC)
Port 1~6 (JNM5-2SFP/4SSC)
Port 25~28 (Gigabit RJ45)
Port 25~28 (Gigabit SFP)
RS (Ring Status)
Color
Green/Green Blinking
Green/Green Blinking
Green/Green Blinking
Green/Green Blinking
Green/Green Blinking
Green/Green Blinking
(JetNet 5628G-R/5828G-R)
Color
Green On/Off
Green On/Off
Green On/Off
Green On/Off
Green On/Off
Red On/Off
Red On/Off
2.2 Fast Ethernet Module: There are 3 available slots for Fast Ethernet Modules.
2.3 On Board Fixed Ports: 4 10/100/1000Mbps combo with 4 Gigabit SFP sockets.
2.4 Front Switch with Cap: Easy to turn on/off the switch after mounted to rack.
2.5 Digital Input/Output: 8 pin terminal block for Digital Input and Output.
2.6 AC/DC Socket: AC plug for 85-264VAC and DC input (18-48VDC or 88-370VDC).
2.7 RS232 Console: DB-9 RS232 console for out band management.
3. Mounting the Fast Ethernet Module
3.1 Turn off the switch by the front power switch(JetNet 5628G/5828G).
3.2 Unlock the front plate of the slot and plug the Fast Ethernet Module into the socket.
3.3 Turn the captive screw to lock the module.
3.4 After locked the modules, turn on the switch.
Note: Each time when you plug or
exchange module, be noticed that
you should turn off the power
¿UVW
4. Port number of slots: There are 3 slots which provide maximum 24 ports. The slot 1
represents port 1 to 8; the slot 2 represents port 9-16; the slot 3 represents port 17-24. Some
RIWKHPRGXOHVRQO\VXSSRUWSRUWVZKHQSOXJLQSRUWVPRGXOHWKHQXPEHURIWKH¿UVWSRUW
of each slot still starts from port 1, 9 and 17. The 4 On board Gigabit combo ports always
represent port 25-28.
On BoardSlot 3Slot 2Slot 1
Slot
Module
JNM5-8TX
JNM5-4TX/4SFP
JNM5-2SFP/4MSC
JNM5-2SFP/4SSC
Web
1~8
1~8
CLI
fa1~fa8
fa1~fa8
1~6 fa1~fa6
Web
9~16
9~16
Web
17~24
17~24
Web
25~28
25~28
CLI
fa9~fa16
fa9~fa16
CLI
fa9~fa16
fa9~fa16
CLI
gi25~gi28
gi25~gi28
9~14 17~22 25~28fa9~fa14 fa9~fa14 gi25~gi28
5. Mount the Switch to 19’’ rack
5.1 Attach the brackets to the device by using the screws provided in the Rack Mount kit.
5.2 Mount the device in the 19’ rack by using four rack-mounting screws provided by the
rack manufacturer.
6. Power the unit and connect to network Cable
6.1 Connect the power supply; the terminal block is for low voltage DC input, and the AC
socket is for high voltage AC/DC input.
6.2 Connect the 10/100M Copper Port: Connect the network nodes to the switch with
2/4-pair CAT5 UTP cable. The 10/100M interfaces support auto MDI/MDIX.
&RQQHFWWKH%DVH);6)3WUDQVFHLYHU3OXJLQ%DVH);6)3¿EHUWUDQVFHLYHU
Connect transmit channel to receive channel at the opposite end using LC type Fiber cable.
6.4 Connect the 100Base-FX Single or Multi mode SC type Connector. Connect transmit
channel to receive channel at the opposite end using SC type Fiber cable.
6.5 Connect the Gigabit Copper Port: Connect the network node to the JetNet 5628G/5828G
with 4-pair CAT5 UTP cable. The on board 1000Base-T ports support 10/100/1000Mbps
and auto MDI/MDIX.
6.6 Connect the Gigabit SFP transceiver of the on board SFP sockets: Plug in Gigabit SFP
¿EHUWUDQVFHLYHU&RQQHFWWUDQVPLWFKDQQHOWRUHFHLYHFKDQQHODWWKHRSSRVLWHHQGXVLQJ/&
type Fiber cable. The 4 On board SFP sockets support 1000Base-X Single or Multi mode
Fiber transceiver.
5.3 When installing multiple switches, mount
them in the rack one below the other.
Note: Check if the rack environment
WHPSHUDWXUHFRQIRUPVWRWKHVSHFL¿HG
operating temperature range. Do not
place any equipment on top of the
switch and please properly ground it.
1RWH:HUHFRPPHQGXVLQJ.RUHQL[FHUWL¿HG6)3PLQL*%,&WUDQVFHLYHU
Note 2: Cross-connect the transmit channel at each end to the receive channel at the
RSSRVLWHHQGDVLOOXVWUDWHGLQWKH¿JXUHEHORZ
Warming: The Fiber interface is Class 1 Laser/LED product. Do not look into the
Laser/LED beam.
1.1 Go to Start -> Program -> Accessories -> Communication -> Hyper Terminal
1.2 Give a name to the new console connection.
1.3 Choose the COM name, and select the correct serial settings. The serial settings of
the JetNet 5628G are as below: Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop Bit: 1
1.4 After connected, you can see Switch login request. Type the username and password
then you can login. The default username is “admin”, password is “admin”.
)ROORZWKHPDQXDOWRFRQ¿JXUHWKHVRIWZDUHIHDWXUHV
RX
TX
RX
TX
SC Connector
Cable Wiring(SC to SC)
AB
TX
RX
TX
RX
Cable Wiring (LC to LC)
SFP Connector (100Base-FX/1000Base-x)
Device Management
JetNet 5628G/5828G Rack Mount Managed Ethernet Switch provides both in-band and
RXWEDQGFRQ¿JXUDWLRQPHWKRGV<RXFDQFRQ¿JXUHWKHVZLWFKYLDWKH56FRQVROHZLWK
the attached console cable. Or you can remotely manage the switch via network. You can
choose Telnet/SSH, Web/HTTPS management.
1. Preparation for console management: Attach the RS-232 DB9 connector to your PC’s
COM port. Connect the RJ-45 connector to the console port of the JetNet 5628G/5828G.
2. Preparation for Web management: Before you attempt to use the embedded web interface
to manage switch operation, verify that your JetNet 5628G/5828G is properly installed on
your network and that every PC on this network can access the switch via the web browser.
2.1 Launch the web browser (Internet Explorer or
Mozilla Firefox) on the PC.
2.2 Type http://5628G/5828G_IP_Address (The default
IP address is 192.168.10.1.) then press Enter.
2.3 The login screen will appear next. Key in the user
name and the password. The default user name and
password is admin/admin.
2.4 Click OK, and then the Home page of the
web-based management interface will appear.
2.5 At the left column of the web management
interface is the software function. The right
column lists the available settings. The top
column indicates the front panel and shows
the link status of each interface.
Korenix Customer Service
KoreCARE is Korenix Technology’s global service center, where our professional staff is
ready to answer your questions any time.
3. Preparation for Telnet management: Go to Start -> Program -> Accessories -> DOS
Prompt, Type Telnet 192.168.10.1 (Default IP Address) then press Enter.
概述
JetNet 5628G/5828G ᱥ19-inch 1U⁗ඍ24+4G㖇㇗ශᐛѐԛའ㖇Ӛᦘᵰθ䞃༽3Ѡԛའ㖇
⁗ඍᨈ″θᴶཐ㓺24Ѡ10/100 Base-TX ㄥᡌ18Ѡ100Base-FX Fݿ㓚θԛ4Ѡ
ݼRJ45 / MINI GBIC combo䘿ㄥȾJetNet 5628G/5828GщѰ⭫ㄏ㠠ࣞԛᐛѐ
ѣᗹ㊱ᓊ⭞㙂䇴䇗θ┗䏩IEC61850-3θIEEE1613儎ㅿ㓝⭫⧥ູ䇚䇷ȾӚᦘᵰ䘎᭥ᤷ
Jumbo Frameᐞᑝ㇗⨼ᴶ儎䗴9.2KbytesȾ↚亯ࣕ㜳θֵཝᮽԬՖ䗉ᗍᴪࣖ儎᭾䶖ȾѰҼ
ޞ䶘┗䏩⭫ㄏѣᗹⲺ儎㓝㖇㇗θᆿޞ㇗⨼䴶≸θJetNet 5628G/5828G䘎᭥ᤷ
ѦሂⲺ䖥Ԭࣕ㜳θׁྸVLANθMSRθRSTPθQoSθIGMPθACLθ802.1xθDHCP Option
82θSNMPθLLDPㅿθ䘸〃ᓊ⭞ᐛぁӰⲺ䇴䇗θᬃ֒㾷≸Ⱦ
JetNet 5828GфJetNet 5628G⺢Ԭ䇴䇗ᶺ䙖θ䲚↚ҁཌ, JetNet 5828G᭥ᤷ3ቸӚᦘ/䐥⭧
ࣕ㜳Ⱦ JetNet 5628G-R/5828G-Rࡏᱥр䘦ශⲺᢟኋθᱥ䟽⭞࠰㓵䇴䇗Ⱦᡶᴿᘡ䙕ԛའ㖇
⁗ඍൽ䘸⭞JetNet 5628G/5828G㌱ࡍᵰශȾ
1. ᢉᔶ㻻Ỷḛ䞃Ԭ
ᵰᕅ㖇㇗ශӚᦘᵰ(4GT Comboθуԛའ㖇⁗ඍ)
RS-232 DB9 (Null-Modem) 㓵㔼
ᵰᆿ㻻䞃Ԭ
⭫Ⓠ㓵(ṯᦤളᇬḽ㙂у)
2. ⮂䶘ԁ㔃(JetNet 5628G/5828G)
2.1 LED:
硬件安装
㌱㔕LED⽰⚥
PWR 1, PWR 2 (AC/ HDC)
DC 1, DC 2 (LDC Power)
RDY (㌱㔕ቧ㔠)
DI 1, DI 2 (ᮦᆍ䗉ޛ)
R.M. (Ring Master)
DO 1, DO 2 (ᮦᆍ䗉࠰)
R.F. (⧥㖇᭻䳒)
ㄥLED⽰⚥
Port 1~8 (JNM5-8TX)
Port 1~8 (JNM5-4TX/4SFP)
Port 1~6 (JNM5-2SFP/4MSC)
Port 1~6 (JNM5-2SFP/4SSC)
Port 25~28 (Gigabit RJ45)
Port 25~28 (Gigabit SFP)
RS (Ring Status)
颜色
㔵⚥Ӥ/㔵⚥䰠⛷
㔵⚥Ӥ/㔵⚥䰠⛷
㔵⚥Ӥ/㔵⚥䰠⛷
㔵⚥Ӥ/㔵⚥䰠⛷
㔵⚥Ӥ/㔵⚥䰠⛷
㔵⚥Ӥ/㔵⚥䰠⛷
(JetNet 5628G-R/5828G-R)
颜色
㔵⚥Ӥ/➺⚣
㔵⚥Ӥ/➺⚣
㔵⚥Ӥ/➺⚣
㔵⚥Ӥ/➺⚣
㔵⚥Ӥ/➺⚣
㓘⚥Ӥ/➺⚣
㓘⚥Ӥ/➺⚣
CH
2.1 ᘡ䙕ԛའ㖇⁗ඍ: 3Ѡԛའ㖇⁗ඍᨈ″Ⱦ
2.2 രㄥ: 4Ѡ10/100/1000Mbpsሯᓊ4ѠݼSFPᨈ″䘿ㄥȾ
2.3 ࢃ䶘ᶵᔶީ: ᇂᡆᵰᆿ㻻θӄࣞᡌީ䰣ӚᦘᵰȾ
2.4 DI/O: 8 pin㓵″⭞ӄ䘔ᮦᆍ䗉ޛ/䗉࠰ؗȾ
2.5 AC/DC⭫Ⓠ䗉ޛ: ACӚ⍷⭫䗉ޛ㤹പѰ85-264VACθDC⍷⭫䗉ޛ㤹പѰ18-48VDCᡌ
88-370VDCȾ
2.6 RS232ㄥ: DB-9⮂䶘RS232ㄥ⭞ӄᑜཌ㇗⨼Ⱦ
3. ᆿ㻻ᘡ䙕ԛའ㖇⁗ඍ
3.1 ީ䰣Ӛᦘᵰࢃ䶘ᶵ⭫Ⓠᔶީ(JetNet 5628G/5828G)Ⱦ
3.2 মсᨈ″ࢃ䶘Ⲻᥗᶵθሼᘡ䙕ԛའ㖇⁗ඍᨈޛᨈ″Ⱦ
3.3 ᰁ䖢㷰䪿ሼ⁗ඍരᇐȾ
3.4 ⁗ඍരᇐθᢉᔶ⭫ⓆᔶީȾ
༽⌞: ∅⅗ᨈޛᡌᴪᦘ⁗ඍҁࢃθ
䈭⺤䇚Ӛᦘᵰ⭫Ⓠᐨ㔅ީ䰣Ⱦ
4. ᨈ″ㄥ: 3Ѡᨈ″᭥ᤷᴶཐ24ѠㄥȾslot 1ሯᓊport 1㠩8χslot 2 ሯᓊport 9㠩16χslot
3ሯᓊport 17㠩24Ⱦᴿжӑ⁗ඍӻᨆב6Ѡㄥθᖉᨈޛ6ㄥⲺ⁗ඍᰬθ∅Ѡᨈ″ሯᓊⲺㄥ
ԃԄport1θ9θ17ᔶခȾ4ѠരⲺݼCombo䘿ㄥခ㓾ሯᓊport 25㠩28Ⱦ
Slot 3Slot 2Slot 1
插槽
⁗ඍ
JNM5-8TX
JNM5-4TX/4SFP
JNM5-2SFP/4MSC
JNM5-2SFP/4SSC
Web
1~8
1~8
CLI
fa1~fa8
fa1~fa8
1~6 fa1~fa6
Web
9~16
9~16
Web
17~24
17~24
Web
25~28
25~28
CLI
fa9~fa16
fa9~fa16
CLI
fa9~fa16
fa9~fa16
CLI
gi25~gi28
gi25~gi28
9~14 17~22 25~28fa9~fa14 fa9~fa14 gi25~gi28
固定端口
5. ሼӚᦘᵰᆿ㻻ࡦ19Ĉᵰ
5.1 ᤵ࠰ᵰᆿ㻻䞃Ԭθ⭞㷰ѓሼ᭥രᇐ൞ӚᦘᵰрȾ
5.2 ⭞ᵰসᨆבⲺരᇐ㷰ѓሼӚᦘᵰ㻻ޛᵰḒᒬരᇐȾ
5.3 ᖉ䴶㾷ᆿ㻻ཐӚᦘᵰᰬθ䙆жсᧈࡍᆿ㻻Ⱦ
6. Ѱ䇴༽ב⭫θ䘔㖇㔒㓵
6.1 䘔⭫Ⓠ; 㓵″⭞ӄքু⍷䗉ޛθACᨈᓝ⭞ӄ儎ুӚ/⍷䗉ޛȾ
6.2 䘔10/100M⭫: ⭞2/4-pair CAT5 UTP㔔㓵ሼ㖇㔒㢸⛯ޛӚᦘᵰθ10/100Mㄥ
㠠䘸ᓊMDI/MDIXȾ
6.3 䘔100Base-FX SFPݿ㓚᭬ಞ⁗ඍ: ሼ100Base-FX SFPݿ㓚᭬ಞ⁗ඍᨈޛᨈ″Ⱦ
⭞LCཪݿ㓚㓵ሼ䘷ㄥ䘔ࡦⴤⲺ䇴༽Ⲻ᭬ㄥθ䘑㺂Ӛӈ䘔Ⱦ
6.4 䘔100Base-FXঋ⁗ᡌཐ⁗SCཪ: ⭞SCཪݿ㓚㓵ሼ䘷ㄥ䘔ࡦⴤⲺ䇴༽Ⲻ᭬
ㄥθ䘑㺂Ӛӈ䘔Ⱦ
6.5 䘔ݼ⭫: ⭞4-pair CAT5 UTP㔔㓵ሼ㖇㔒㢸⛯ޛJetNet 5628G/5828Gθര
Ⲻ1000Base-T⭫᭥ᤷ 10/100/1000Mbps㠠䘸ᓊૂMDI/MDIX㠠䘸ᓊȾ
6.6 䘔രSFPᨈ″ⲺݼSFPݿ㓚᭬ಞ⁗ඍ: ሼݼSFPݿ㓚᭬ಞ⁗ඍᨈޛᨈ″Ⱦ⭞
LCཪݿ㓚㓵ሼ䘷ㄥ䘔ࡦⴤⲺ䇴༽Ⲻ᭬ㄥθ䘑㺂Ӛӈ䘔Ⱦ4ѠരⲺSFPᨈ″᭥ᤷ
1000Base-X ঋ⁗ᡌཐ⁗ݿ㓚᭬ಞ⁗ඍȾ
༽⌞: ỶḛᵰḒ⧥ູᓜᱥ┗䏩Ӛᦘ
ᵰᐛ֒ᓜ㤹പȾу㾷൞Ӛᦘᵰ京䜞᭴㖤
Ա䇴༽θᒬ⺤䇚ᵰ䓡൦Ⱦ
༽⌞1: ᧞㦆䘿⭞䙐䗽Korenix䇚䇷ⲺSFP mini GBIC᭬ಞ⁗ඍȾ
༽⌞2: ⺤䇚ሼ䘷ㄥ䘔ࡦⴤⲺ䇴༽Ⲻ᭬ㄥθ䘑㺂Ӛӈ䘔θྸсഴᡶ⽰Ⱦ
⌞ᝅ: ↚ѰClass 1 Laser/LEDݿӝθ࠽㿼◶ݿ/LEDݿ䙕Ⱦ
1.1 䘆㺂Start(ࣞ) -> Program(ぁᓅ) -> Accessories(䱺Ԭ) -> Communication(䙐䇥) ->
Hyper Terminal(䎻㓝㓾ㄥ)
1.2 Ѱ䘔㓵ળȾ
1.3 䘿COMㄥθ䇴ᇐ↙⺤ⲺѨ৸ᮦȾJetNet 5628GⲺѨ৸ᮦྸсφ
Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop Bit: 1
1.4 䘔θՐ࠰⧦ӚᦘᵰⲺⲱᖋᨆ⽰Ⱦ䭤ޛ⭞ᡭᇼ⸷ⲱᖋȾ唎䇚⭞ᡭᱥ
ćadminĈθᇼ⸷ᱥćadminĈȾ
1.5 ṯᦤ⭞ᡭᢁ߂䘑㺂ࣕ㜳䇴㖤Ⱦ
RX
TX
RX
TX
SC Connector
Cable Wiring(SC to SC)
AB
TX
RX
TX
RX
Cable Wiring (LC to LC)
SFP Connector (100Base-FX/1000Base-x)
设备管理
JetNet 5628G/5828Gᵰᕅ㖇㇗ශᐛѐԛའ㖇Ӛᦘᵰ᭥ᤷᑜ(in-band)ᑜཌ(out-band)䇴㖤
⁗ᕅȾ⭞ᡭԛ䙐䗽RS232ㄥሯӚᦘᵰ䘑㺂䇴㖤θᡌ䙐䗽㖇㔒䘑㺂䘒ぁ㇗⨼Ⱦᛞ䘎ԛ
䘿Telnet/SSH, Web/HTTPSཐ〃㇗⨼⮂䶘Ⱦ
1. Console㇗⨼Ⲻ༽ᐛ֒: ሼRS-232 DB9ཪㄥ䘔ࡦ֖䇗㇍ᵰⲺCOMθሼRJ-45ㄥᨈޛ
JetNet 5628G/5828GⲺConsleㄥȾ
Altri manuali per JetNet 5628G Series
2
Questo manuale è adatto per i seguenti modelli
3
Indice
Lingue:
Altri manuali Korenix Interruttore
Korenix
Korenix JetNet 3212G-2C2F Manuale utente
Korenix
Korenix JetNet 3706 Manuale utente
Korenix
Korenix JetNet 7850G-2XG Manuale utente
Korenix
Korenix JetNet 3808G-M12 Series Manuale utente
Korenix
Korenix JetNet 5428G-20SFP Series Manuale utente
Korenix
Korenix JetNet 5210G Manuale utente
Korenix
Korenix JetNet 5428G Series Manuale utente
Korenix
Korenix JetNet 4706 Manuale utente
Korenix
Korenix JetNet 7020G Manuale utente
Korenix
Korenix JetNet 7310G Series Manuale utente
Korenix
Korenix JetNet 6828Gf-2AC Manuale utente
Korenix
Korenix JetNet 7628X Series Manuale utente
Korenix
Korenix JetNet 4500 Series Manuale utente
Korenix
Korenix JetNet 5210G Manuale utente
Korenix
Korenix JetNet 4508 V2 Series Manuale utente
Korenix
Korenix JetNet 3906G Manuale utente
Korenix
Korenix JetNet 3010G Series Manuale utente
Korenix
Korenix JetNet 3008f Manuale utente
Korenix
Korenix JetNet 3810G(f) Manuale utente
Korenix
Korenix JetNet 3705 Series Manuale utente
