Kramer PA-120Z Manuale utente

PA-120Z / PA-240Z Quick Start (P/N: 2900-300802QS REV 2)

P/N:

2900- 300802QS

Rev:

Scan for full manual

PA-120Z / PA-240Z Quick Start Guide

This guide helps youinstall and use your PA-120Z / PA-240Z for the first time.

Go to www.kramerav.com/downloads/PA-240Z to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

PA-120Z / PA-240Z 120W / 240W Power Amplifier

4 Rubber feet

1 Power cord

1 Quick start guide

Step 2: Get to know your PA-120Z / PA-240Z

Feature

Function

ON LED

Lights green when powered on, orange when in standby.

INPUT 1 LED

Lights green when a signal is present on input 1.

INPUT 2 LED

Lights green when a signal is present on input 2.

MUTE

Lights red when the output is muted, off when unmuted.

CLIP LED

Lights red when the signal is clipped on the output and creating distortion.

(When clipping is detected, lower the volume until the LED turns off.)

PROTECT LED

Lights red in case of over current / short / over heat.

The device powers down until operation conditions are corrected and then powers up again.

Feature

Function

AUDIO IN

Connectors

Unbalanced Stereo Audio

3.5mm mini jack

Connect to an unbalanced stereo audio source.

balanced Stereo Audio

5-pin Terminal Block

Connector

Connect to a line-level, balanced, stereo audio source.

LINE OUT Balanced Stereo Audio 5-pin

Terminal Block Connector

Connect to a balanced, stereo audio acceptor (for example, amplified speakers).

VOLUME Attenuator

Master volume for speaker output –rotate toset the maximumamplifier volume.

FACTORY DEFAULT Button

Press to return to the factory default settings, including all the configurations and

network settings.

ETHERNET RJ-45 Connector

Connect to an ETHERNET LAN.

RS-232 (G, Tx, Rx) Port

Connect to an RS-232 connector on A/V equipment or a PC or other Serial Controller.

Hi-Z/Lo-Z and 100V/70V

DIP-Switches

Set to Hi-Z for high impedance and Lo-Z for low impedance.

In Hi-Z, set to 70V or 100V.

Lo-Z/Hi-Z Out Terminal Block Connectors

Lo-Z –connect stereo output to Lo-Z speakers:

L+ and L- to the left speaker; R+R- to the right speaker.

Hi-Z (70V or 100V) –connect Hi-Z and COM to mono Hi-Z speakers.

Speaker can outputeither the left side of the audio input or reduce the stereo input to a

mono signal (via webpages).

Power Connector with Fuse

ACconnector, enabling power supplyto the unit.

Mains Power Switch

Switch forturning the device on or off.

Step 3: Install the PA-120Z / PA-240Z

Install PA-120Z / PA-240Z using one of the following methods:

Mount the unit in a rack using an optional RK-1 rack adapter.

Attach the rubber feet and place the unit on a flat surface.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your PA-120Z / PA-240Z. Forbestresults, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the PA-120Z / PA-240Z.

RJ-45 Pinout:

Connect the audio line out:

PIN EIA /TIA 568B

To a balanced stereo audio acceptor:

To an unbalanced stereo audio

acceptor:

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

To a balanced stereo audio source:

To an unbalanced stereo audio

source:

Step 5: Connect the power

Connect the power cord to PA-120Z / PA-240Z and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Control PA-120Z / PA-240Z via the embedded web pages

RS-232

Protocol 3000

Baud Rate:

115,200

Stop Bits:

Data Bits:

Parity:

None

Change the volume of input 2 to -10 DB

#X-AUD-LVL 1,2,-10

TCP/IP Parameters

IP Address:

192.168.1.39

Maximum UDP Connections:

Unlimited

UDP Port #:

50000

Subnet mask:

255.255.000.000

Maximum TCP Connections:

Unlimited

TCP Port #:

5000

Default gateway:

192.168.0.1

Full Factory Reset

Protocol 3000

Excluding ETH: use “#FACTORY” command and use “#RESET” to restore the factory default values.

Technical Specifications

PA-120Z

PA-240Z

Input:

1 unbalanced stereo on a 3.5mm connector

1 balanced stereo +4dBu/10kΩ on a 5-pin terminal block

Output:

1 balanced stereo line level on a 5-pin terminal block

1 stereo or 1 mono speaker output on a 4-pin large terminal block

Input Sensitivity:

Full power @ 0.3V (–10dBV)

Output Power:

2 x 60W @ 4Ω or 8Ω

1 x 120W @ 70V or 100V

2 x 120W @ 4Ω or 8Ω

1 x 240W @ 70V or 100V

Amplifier Type:

Class D

Maximum Voltage Gain:

26dB SE / 32dB BTL

Dynamic Range

119dB

Frequency Response

20Hz to 20kHz @ +/-1dB

S/N Ratio:

80dB -10dBV, 20 Hz -20 kHz

Controls:

Screw trimmer amplifier attenuator, IP and RS-232

Audio THD + Noise:

THD+N (1kHz @ 1W) 0.003 %

Audio 2nd Harmonic:

0.08% @ 75W RMS @ 4Ω 6.67kHz

Power Source:

Universal mains operational voltage

85VAC –265VAC

Universal mains operational voltage

85VAC –265VAC )full power at 120V –230V)

Total System Efficiency

89.2%

89.5%

Dimensions:

21.2cm x22.8cm x4.3cm (8.35" x 8.98" x 1.69")W,D, H

Weight:

1.0kg (2.2lbs) approx.

Included Accessories:

Power cord

Options:

RK-1 rack adapter

Specifications are subject to change without notice at www.kramerav.com

Altri manuali per PA-120Z

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Kramer Amplificatore

Kramer

Kramer VS-202YC Manuale utente

Kramer

Kramer VM-3S Manuale utente

Kramer

Kramer Tools VP-200Dxl Manuale utente

Kramer

Kramer VM-3UHD Manuale utente

Kramer

Kramer 104LN Manuale utente

Kramer

Kramer PT-571 Manuale utente

Kramer

Kramer TOOLS VP-200NK Manuale utente

Kramer

Kramer 100 Manuale utente

Kramer

Kramer TP-310A Manuale utente

Kramer

Kramer 900 Manuale utente

Kramer

Kramer VM-100YC Manuale utente

Kramer

Kramer VM-4HC Manuale utente

Kramer

Kramer VP-200AK Manuale utente

Kramer

Kramer VM-4HDCPxl Manuale utente

Kramer

Kramer VM-50AN Manuale utente

Kramer

Kramer VP-400 Manuale utente

Kramer

Kramer VP-6A Manuale utente

Kramer

Kramer TOOLS VP-210XL Manuale utente

Kramer

Kramer VP-242 Manuale utente

Kramer

Kramer 907xl Manuale utente

Kramer

Kramer VP-108 Manuale utente

Kramer

Kramer TOOLS 900xl Manuale utente

Kramer

Kramer VP-200N-5 Manuale utente

Kramer

Kramer VM-22HD Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente