KTI Networks KFS-0840 Manuale utente
KFS-0840
Industrial 8-Port Fast Ethernet Switch
Installation Guide
-1-
DOC.091111
(C) 2009 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form
or by any means or used to make any directive work (such as translation or transformation) without permission
from KTI Networks Inc.
KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to
time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.
For more information, contact:
United States KTI Networks Inc.
P.O. BOX 631008
Houston, Texas 77263-1008
Phone: 713-2663891
Fax: 713-2663893
URL: http://www.ktinet.com/
International Fax: 886-2-26983873
URL: http://www.ktinet.com.tw/
-2-
The information contained in this document is subject to change without prior notice. Copyright (C) All Rights
Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including the interference that may cause undesired operation.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the European
Community. Such marking is indicative that this equipment meets or exceeds the following technical
standards:
EMC Class A
EN55022:2006
EN61000-3-2:2006
EN61000-3-3:1995/A1:2001/A2:2005 Class A
EN 55024:1998/A1:2001/A2:2003
IEC 61000-4-2:2001
IEC 61000-4-3:2002/A1:2002
IEC 61000-4-4:2004
IEC 61000-4-5:2001
IEC 61000-4-6:2003
IEC 61000-4-8:2001
IEC 61000-4-11:2001
-3-
-4-
Table of Contents
1. Introduction...................................................................................................................................5
1.1 Features................................................................................................................ 6
1.2 Product Panels...................................................................................................... 6
1.3 LED Indicators ...................................................................................................... 7
1.4 Specifications........................................................................................................ 7
2. Installation.....................................................................................................................................9
2.1 Unpacking ............................................................................................................. 9
2.2 Safety Cautions..................................................................................................... 9
2.3 Mounting the Switch to a Din-Rail....................................................................... 10
2.4 Mounting the Switch on a Panel ......................................................................... 12
2.5 Applying Power ................................................................................................... 14
2.5.1 Using Terminal Blocks ..................................................................................... 15
2.5.2 Using DC Power Jack ...................................................................................... 16
3. Making LAN Connections..........................................................................................................17
3.1 10/100 Copper Ports........................................................................................... 17
3.2 LED Indication..................................................................................................... 17
1. Introduction
The switch provides eight 10/100Mbps copper ports for connections to Ethernet and Fast Ethernet devices.
With the featured auto-negotiation function, the switch can detect and configure the connection speed and
duplex automatically. The switch also provides auto MDI/MDI-X function, which can detect the connected
cable and switch the transmission wire pair and receiving pair automatically. This auto-crossover function can
simplify the type of network cables used.
For industrial environment, the device is designed with the following enhanced features exceeding that of
commercial Ethernet switches:
zHigh and wide operating Temperature
zPower input interface: Industrial screw terminal block and DC power jack for external commercial power
adapter as option
zScrew panel and DIN rail mounting support for industrial enclosure
zIndustrial-rated Emission and Immunity performance
-5-
1.1 Features
zAuto MDI/MDI-X crossover function on the copper port
zSupport IEEE 802.3x flow control for full-duplex operation
zSupport Back-pressure flow control for half-duplex operation
zWide operating temperature range for temperature critical environment
zSupport DIN-rail mounting and panel mounting
zProvide two power input types to meet more application needs
zPower saving mode for port link down
zAccept wide power input voltage range for application flexibility
zIndustrial-rated Emission and Immunity performance
1.2 Product Panels
The following figure illustrates the panels of the switch:
-6-
-7-
1.3 LED Indicators
LED Function
POWER Power status
1 - 8 Port 1 – Port 8
LINK (Green) Link and activity status (Port 1 - Port 8)
100M (Yellow) 100Mbps speed status (Port 1 - Port 8)
1.4 Specifications
10/100 Copper Ports
Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Connectors Shielded RJ-45 jacks
Pin assignments Auto MDI/MDI-X detection
Configuration Auto-negotiation or software control
Transmission rate 10Mbps, 100Mbps
Duplex support Full/Half duplex
Network cable Cat.5 UTP up to 100 meters
Switch Functions
Forwarding & filtering Non-blocking, full wire speed
Switching technology Store and forward
Maximum packet length 1536 bytes
MAC Addresses Table 1K entries
Port configuration Auto-negotiation for speed and duplex
Flow control IEEE 802.3x pause frame base for full duplex operation
Back pressure for half duplex operation
MAC Aging time 300 seconds
Storm control Broadcast packets are dropped when more than 64 broadcast packets are received.
DC Power Input
Screwed terminal block 3P (Vin+, Vin-, Chassis Ground)
DC Jack Connector -D 6.3mm / + D 2.0mm
Operating Voltages +7 ~ +30VDC
Power Consumption 2.3W max.
Power Saving Mode Total consumption 0.28W when all ports link down
Mechanical
Dimension (base) 40 x 80 x 95 mm (WxDxH)
-8-
Housing Enclosed metal with no fan
Mounting Din-rail mounting
Panel mounting (optional)
Environmental
Operating Temperature Typical -10oC ~ +70oC
Storage Temperature -20oC ~ +85oC
Relative Humidity 10% ~ 90% non-condensing
Electrical Approvals
FCC Part 15 rule Class A
CE EMC, CISPR22 Class A
EN55022:2006
EN61000-3-2:2006
EN61000-3-3:1995/A1:2001/A2:2005 Class A
EN 55024:1998/A1:2001/A2:2003
IEC 61000-4-2:2001
IEC 61000-4-3:2002/A1:2002
IEC 61000-4-4:2004
IEC 61000-4-5:2001
IEC 61000-4-6:2003
IEC 61000-4-8:2001
IEC 61000-4-11:2001
Safety LVD, IEC60950-1
-9-
2. Installation
2.1 Unpacking
The product package contains:
zThe switch unit for Din-rail mounting
zOne product CD-ROM
2.2 Safety Cautions
To reduce the risk of bodily injury, electrical shock, fire and damage to the product, observe the following
precautions.
zDo not service any product except as explained in your system documentation.
zOpening or removing covers may expose you to electrical shock.
zOnly a trained service technician should service components inside these compartments.
zIf any of the following conditions occur, unplug the product from the electrical outlet and replace the part
or contact your trained service provider:
- The power cable, extension cable, or plug is damaged.
- An object has fallen into the product.
- The product has been exposed to water.
- The product has been dropped or damaged.
- The product does not operate correctly when you follow the operating instructions.
zDo not push any objects into the openings of your system. Doing so can cause fire or electric shock by
shorting out interior components.
zOperate the product only from the type of external power source indicated on the electrical ratings label. If
you are not sure of the type of power source required, consult your service provider or local power
company.
2.3 Mounting the Switch to a Din-Rail
In the product package, a DIN-rail bracket is provided or has been installed for mounting the switch in a
industrial DIN-rail enclosure.
The steps to mount the switch onto a DIN rail are:
1. Install the mounting bracket onto the switch unit with screws as shown below:
2. Attach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can
clamp on the upper edge of the DIN rail.
-10-
Indice
Altri manuali KTI Networks Router di rete
KTI Networks
KTI Networks KSD-800M Series Manuale utente
KTI Networks
KTI Networks KS-2260 Manuale utente
KTI Networks
KTI Networks 100BASE-TX Manuale utente
KTI Networks
KTI Networks KGS-1260/G Manuale utente
KTI Networks
KTI Networks KGS-612F Manuale utente
KTI Networks
KTI Networks KSD-103-B Series Manuale utente
KTI Networks
KTI Networks KS2028 Manuale utente
KTI Networks
KTI Networks KGD-600 Manuale utente
KTI Networks
KTI Networks KGS-2404 Manuale utente
KTI Networks
KTI Networks KGS-810F Manuale utente
KTI Networks
KTI Networks KS-115FM Manuale utente
KTI Networks
KTI Networks KS-MINI-5P Manuale utente
KTI Networks
KTI Networks KGD-600 Manuale utente
KTI Networks
KTI Networks KGS-2402 Manuale utente
KTI Networks
KTI Networks KS-324F Manuale utente
KTI Networks
KTI Networks KGS-0600 Manuale utente
KTI Networks
KTI Networks Gigabit Ethernet Switches Manuale utente
KTI Networks
KTI Networks 10BASE-T/100BASE-TX Manuale utente
KTI Networks
KTI Networks KGS-510F Ver.D Manuale utente
KTI Networks
KTI Networks KS-2262 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza