Kuhnke PG 674 Manuale utente

Kuhnke Electronics

Instruction Manual

E 390 GB

PG 674

Operating Terminal for KUAX 674 / 673

4 April 1996 / 65.135

Thismanualisprimarilyintendedfortheuseofthedesigningengineer,the

projectplanningengineer,andthedevelopingengineer.Itdoesnotgiveany

informationaboutdeliverypossibilities.Dataisonlygiventodescribethe

productandmust not be regarded asguaranteedproperties in the legal sense.

Any claims for damages against us – on whatever legal grounds – are excluded

exceptin instancesofdeliberateintent orgrossnegligenceonourpart.

Wereservetherightsforerrors,omissionsormodifications.

Reproductionevenofextractsonlywiththeeditor'sexpressandwrittenprior

consent.

Contents - 1

Table of contents

1. Introduction................................................................ 1-1

2. Reliability, Security...................................................... 2-1

2.1. Target group ............................................................................ 2-1

2.2. Reliability ................................................................................ 2-1

2.3. Notes...................................................................................... 2-2

2.3.1. Danger................................................................................. 2-2

2.3.2. Dangers caused by high contact voltage .................................. 2-2

2.3.3 Important information / cross reference..................................... 2-2

2.4. Security ................................................................................... 2-3

2.4.1. To be observed during project planning and installation............. 2-3

2.4.2. To be observed during maintenance and servicing .................... 2-4

2.4.3. Measures for the prevention of electrostatic charge.................... 2-4

3. Design of the PG 674.................................................. 3-1

3.1. Display and operating elements.................................................. 3-1

3.2. Hand-held terminal PG 674 (674.001.00) .................................. 3-2

3.3. Built-in terminal PG 674 (674.010.00) ....................................... 3-3

3.3.1. Design and Dimensions .......................................................... 3-3

3.3.2. Installation ............................................................................ 3-4

3.3.2.1. Front panel cutout............................................................... 3-4

3.3.2.2. Inserting the built-in terminal................................................. 3-4

3.4. Technical specifications ............................................................. 3-5

Contents - 2

Table of contents

4. The PG 674 as a programming device .......................... 4-1

4.1. General information on the operating terminal ............................. 4-2

4.2. Front view................................................................................ 4-3

4.3. Key pad .................................................................................. 4-4

4.3.1. Function keys ........................................................................ 4-4

4.4. Operating modes of the operating terminal PG 674 ..................... 4-6

4.4.1. Restricted operating mode ...................................................... 4-6

4.5. Display window of the operating terminal PG 674 ....................... 4-7

4.5.1. Standard display ................................................................... 4-7

4.6. Commands of the operating terminal PG 674 .............................. 4-8

4.6.1. Activating the open mode (entering the key code)...................... 4-8

4.6.2. Exiting the open operating mode ............................................. 4-8

4.6.3. Displaying the key code ......................................................... 4-9

4.6.4. Changing the key code .......................................................... 4-9

4.6.5. System information .............................................................. 4-10

4.6.6. Displaying status and error messages..................................... 4-10

4.6.7. Choosing a program............................................................ 4-11

4.6.7.1. Giving access to the choice of program function .................. 4-11

4.6.7.2. Changing the program number ......................................... 4-13

4.6.8. Initializing the cam control unit.............................................. 4-14

4.6.9. Choosing an output ............................................................. 4-15

4.6.10 Programming cams ............................................................. 4-16

4.6.11. Optimizing cams ............................................................... 4-18

4.6.12. Displaying cams ................................................................ 4-19

4.6.13. Deleting cams ................................................................... 4-20

4.6.14. Deleting outputs................................................................. 4-21

4.6.15. Deleting programs ............................................................. 4-21

4.6.16. Copying programs............................................................. 4-22

4.6.17. Program transfer................................................................ 4-23

4.6.18. Activating the dynamic mode of outputs ............................... 4-24

4.6.19. Deadtime compensation ..................................................... 4-25

4.6.20. Time cams ........................................................................ 4-26

4.6.21. Encoder speed reduction – electronic gearing ....................... 4-27

4.6.22. Choice of language ........................................................... 4-28

Contents - 3

Table of contents

4.6.23. Setting the display contrast (as from version 2.0) ................... 4-29

4.6.24. Self-test of the operating terminal (as from version 2.0) .......... 4-30

4.6.25. Self-test of the operating terminal (versions < 2.0).................. 4-32

Index....................................................................... Index-1

Sales & Service

Contents - 4

Table of contents

1 - 1

Introduction

1. Introduction

The PG 674 is a small, handy device with a keyboard and two-

line display. It is used for operating the electronic cam control

units Posi Control KUAX 674 and KUAX 673. It is separated

from the cam control unit to allow variable use. It can be con-

nected with the cam control unit via the programming interface

at any time, even when the machine is running. This makes it

easy to check or modify the programs at the machine.

Choice of prog

Choice of output

Outputs off

Delete

Outputs on

Gear

Time cam

Show errors

Set cam

Choice of cam

1 - 2

Introduction

The PG 674 is available in two designs:

Hand-held terminal

As a portable hand-held terminal it can easily be transported

and connected to the control device. The integrated buffered

memory allows you to load programs from one controller and

transfer them to another controller.

Built-in terminalAs a built-in terminal the device is firmly built into i.e. the

door of the switching cabinet and is thus permanently available

as an operating and display device.

The present operating manual exclusively describes the hard-

ware of the PG 674 and how you use it to operate controllers.

The control devices themselves are described elsewhere:

Controller Instruction manual

KUAX 674 E 375 GB

KUAX 673 E 293 GB

2 - 1

Reliability/Security

2. Reliability, Security

2.1. Target group

This instruction manual contains all information necessary for

the use of the described product (control device, software, etc.)

according to instructions. It is written for the personnel of thepersonnel of the

personnel of thepersonnel of the

personnel of the

construction, project planning, service and commissioningconstruction, project planning, service and commissioning

construction, project planning, service and commissioning

departmentsdepartments

departments. For proper understanding and error-free applica-

tion of technical descriptions, instructions for use and particu-

larly of notes of danger and warning, extensive knowledge ofextensive knowledge of

extensive knowledge ofextensive knowledge of

extensive knowledge of

automation technologyautomation technology

automation technology is compulsory.

2.2. Reliability

Reliability of Kuhnke controllers is brought to the highest pos-

sible standards by extensive and cost-effective means in their

design and manufacture.

Amongst which are:

· selecting high-quality components,

· quality arrangements with our sub-suppliers,

· measures for the prevention of static charge during the hand-

ling of MOS circuits,

· Worst-Case dimensioning of all circuits,

· inspections during various stages of fabrication,

· computer aided tests of all assembly groups and their

coefficiency in the circuit,

· stress-test in raised ambient temperatures during 72 hours

realtime with nominal load on the outputs,

· statistic assessment of the quality of fabrication and of all re-

turned goods for immediate taking of adjustment measures.

Despite these measures, the occurrence of errors in electronic

control units - even if most highly improbable - must be taken

into consideration.

Text muß n

2 - 2

Reliability/Security

2.3. Notes

Please pay particular attention to the additional notes which we

have marked by symbols in this instruction manual:

2.3.1. Danger

This symbol warns you of dangers which may cause

death, (grievous) bodily harm or material damage if the

described precautions are not taken.

2.3.2. Dangers caused by high contact voltage

This symbol warns you of dangers of death or (grievous)

bodily harm which may be caused by high contact

voltage if the described precautions are not taken.

2.3.3 Important information / cross reference

This symbol draws your attention to important additional

information concerning the use of the described product.

It may also indicate a cross reference to information to be

found elsewhere.

Indice

Altri manuali Kuhnke Terminale touch

Kuhnke

Kuhnke Ventura Vico Manuale utente

Manuali Terminale touch popolari di altre marche

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuale utente

Ingenico

Ingenico AXIUM EX4000 Manuale utente

Heisei Electronics

Heisei Electronics Q-POS 815 Manuale utente

Amano

Amano MTX-15 Manuale utente

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuale utente

Demco

Demco SP7 Manuale utente

Lathem

Lathem PC600 Series Manuale utente

Partner

Partner MF-2352 Manuale utente

NCR

NCR RealPOS 7460-2 Manuale

Simrad

Simrad MS50 Istruzioni per il montaggio

Unitech

Unitech MR350 MKII Guida rapida

Jungheinrich

Jungheinrich WMT 210 Manuale utente

Motorola

Motorola MTP850 Manuale utente

YASKAWA

YASKAWA 62H-MDC0 Manuale utente

MVG industries

MVG industries NeptuLink Manuale utente

Price Industries Limited

Price Industries Limited FDC Manuale di istruzioni

Honeywell

Honeywell TemaKey Manuale utente

EBN

EBN BPC65-B-A16G Manuale utente