Kuzma STABI R Manuale utente

1

KUZMA STABI R WOOD FRAME ASSEMBLY- in the photo, a

wooden frame fitted with Stabi R base turntable

Instruction manual

2022-07

2

KUZMA LTD

INSTRUCTION MANUAL FOR STABI R WOODEN

FRAME ASSEMBLY-PLINTH

The Stabi R base turntable can be fitted into the Kuzma supplied wooden frame -plinth.

CONTENTS: Page

General 2

Technical data 2

Unpacking 2

Preparing Stabi R 3

Assembling 3

Tonearm mounting 4

Maintenance 4

General

Stabi R wooden frame-plinth is made from solid walnut and plywooda into which you can fit

the Stabi R base turntable. The armboard block is supplied with the Kuzma 9 inch arm cut.

The Stabi R plinth is supported on three fully adjustable metal feet.

For more details read instruction manual for Stabi R wood turntable and check plinth dimensions

which are both available on our web site.

Technical data:

Mass 9 kg

Plinth: walnut( oil protected)

Levelling yes (3 adjustable feet)

Armboard yes ( armboard block)

No. of tonearms 1

Dimensions 500 x 463 x 113 mm

Accessories supplied Torx bit T30, screws 3 x M6x40, 2x wooden screws

Basic Setup

Note: Some parts are heavy, so be careful when handling!

Note: Choose a suitable supporting table which can hold over 40 kg without warping.

Unpacking

The plinth is packed in one box. Before unpacking prepare the area where the assembly will take

place.The best position is on a solid table which is strong and rigid enough to support 40-50 kg.

3

Preparing Stabi R for plinth fitting

Depending on which version of the turntable you have, remove all parts from the base: platter,

belt, subplatter, tonearm, armwing, arm holders, arm balconies,supporting spikes, side panels, un

plug cable and it is best to remove the bearing shaft with oil reservoir by removing 3 screws using

Allen key 3 mm. See Fig. 1.&2.

Fig. 1. Stabi R base top view Fig. 2. Stabi R base bottow view

Assembling

Place the sheet of white foam from packing box on the table.

Place Stabi R base with the top down. See Fig. 2.

Over Stabi R base put plinth face down over the base. See Fig. 3.

Check alignement of holes and manually fit three fixing screws M 6x40 and secure them by

using Allen key 5mm. See Fig. 3.

Turn the whole assembly turn back and remove foam. Be careful-it is heavy. See Fig. 4.

Position turntable over the edge of table to fix armboard block. Fix 2 wooden screws into

armboard block. See Fig. 5.

Then return bearing shaft with reservoir and assemble turntable.

Fig. 3. Plinth-bottom view Fig. 4. Stabi R base fitted into plinth

4

Tonearm mounting

Mount the arm as instructed in the tonearm instruction manual. The armboard block is fixed in the

plinth. Under the arm cutout is hole with access underneath to fix the armbase. If required route

the tonearm cable underneath.

Fig. 5. Stabi R with plinth

Maintenance

Wood:

Wipe with damp cloth or special tissues for oiled wood.

Kuzma Ltd

Hotemaze 17A

SI-4205 PREDDVOR

SLOVENIJA

Phone: + 386 4 25 35 450

Fax: + 386 4 25 35 454

E mail: [email protected]. www.kuzma.si

Altri manuali per STABI R

1

Indice

Manuali Giradischi popolari di altre marche

Gemini

Gemini CDT-05 MKII Manuale utente

Rotel

Rotel RP-820 Manuale utente

Shuman

Shuman MC-250BT Manuale utente

Stanton

Stanton STR8-150 Manuale utente

Audio Technica

Audio Technica AT-LPW40WN Manuale utente

Crosley

Crosley McQueen CR7011-GY Manuale utente

Reloop

Reloop SMP-1 Manuale utente

auna

auna TT-Classic Plus Manuale utente

COMO AUDIO

COMO AUDIO Turntable Analog Manuale utente

Dual

Dual 1009 F Manuale utente

REED

REED Muse3C Manuale utente

AXIOMTEK

AXIOMTEK OPS883-H Series Manuale utente

Pioneer

Pioneer PL-71 Manuale utente

Vestax

Vestax PDX-a1 Manuale utente

Denon

Denon DP-400 Manuale utente

Dual

Dual 504 Manuale utente

Audio-Techica

Audio-Techica AT-LP60XBT Manuale utente

Goldring

Goldring G99 Manuale utente