KYMCO Stryker 125 Manuale utente
Dear KYMCO Motorcycle Users:
Before the delivery of each new motorcycle, the fuel in carburetor is
drained off to ensure the excellent performance and safety of the
motorcycle. Therefore, when first starting a new motorcycle, it is
normal to take 20～30 seconds. The quality of each KYMCO
motorcycle is guaranteed.
Dear Users:
We greatly appreciate your patronage of KYMCO STRYKER 125/150
This User‘s Manual describes the correct operating methods, inspection and
maintenance procedures for the KYMCO STRYKER 125/150 details in order
to prolong the service life of motorcycle and provide you with a comfortable
riding.
Please note that the information and illustrations included in this manual may be
different from the motorcycle in case specifications are changed.
To enable you to have a safe and comfortable riding, we recommend you to read
this manual carefully and wish you a happy riding.
Note: 1. The information and specifications stated in this manual are for reference only
and subject to change without notice.
2. When starting the engine, the battery must be installed to facilitate starting
and increase the engine performance.
TABLE OF CONTENTS
1. PRECAUTIONS FORA SAFE RIDING................................................................. 1
2. ASSEMBLY PARTS................................................................................................... 3
3. OPERATION INSTRUCTIONS............................................................................... 5
4. PRE-RIDE INSPECTION....................................................................................... 10
5. ENGINE STARTING METHODS ......................................................................... 19
6. NORMAL RIDING METHOD............................................................................... 22
7. PRECAUTIONS FOR RIDING ............................................................................. 24
8. HOW TO STOP RIDING........................................................................................ 27
9. EASY MAINTENANCE.......................................................................................... 29
10. IMPORTANT NOTICES ........................................................................................ 36
-1-
1. PRECAUTIONS FOR A SAFE RIDING
(1) CLOTHES
yTo relax and wear comfortable clothes are the
main points for a safe riding.
yTo observe traffic laws, keep a cool mind, relax
and be careful will provide you a safe riding.
cWear helmet and fasten it tightly.
dHave the clothes well-arranged. Fasten shirt
cuffs and keep them from hooking the brake
lever.
eWear low-heeled shoes for a safe riding.
fWhen riding, use both hands to grasp the
handlebar. It is very dangerous to hold the
handlebar with one hand.
nCAUTION:
yA motorcycle rider should not wear loose or too
long clothes to avoid danger.
yDuring riding or 10 minutes after the motorcycle
is stopped, do not touch the exhaust muffler to
avoid scalding.
yWhen parking the motorcycle, keep it away from
dry lawn or inflammables to avoid danger.
c
d
e
f
-2-
(2) RIDING METHOD
yThe safety of two-wheel vehicles is influenced by
sitting position. The rider should sit on the central
part of the seat cushion. If the rider sits on the
rear part of the seat, the load of front wheel will
decrease. As a result, the handlebar will swing
and cause danger to the rider.
yWhen making a turn, it will be easier for the rider
to steer the motorcycle by leaning the body
inward slightly. The motorcycle will lose its
balance if the rider fails to keep his body leaning
inward.
yWhen riding on a damaged or macadam road.
Slow down the speed and hold the handlebar
tightly.
(3) CARRYING GOODS
yKeep a good sitting posture to operate the
motorcycle properly.
yThe feel of the handlebar will be different when
carrying goods on the motorcycle. Overloading
may cause the handlebar to swing. Avoid riding
with overload.
cMax. loading capacity of the rear carrier is 3kg.
c
-3-
2. ASSEMBLY PARTS
Engine Serial No.
Clutch panel
Taillight
/
Stoplight
Side Suppor
t
L. Front Turn
Signal Light
Turn Signal Switch
Headlight Dimmer Switch Fuel Tank
Cap
VIN (Vehicle
Identification No.) L. Rear Turn
Signal Light
Tool Boxp
-4-
Starte
r
Button
Kick Leve
r
Rear Brake Leve
r
Ignition
Switch
Exhaust Pipe
Instruments
Frame Serial No.
R. Front Turn
Signal Light
R. Rear Turn
Signal Light
-5-
3. OPERATION INSTRUCTIONS
(1) IGNITION SWITCH/STEERING
HANDLEBAR LOCK
cON :At this position, power is connected to
start the engine. The key cannot be
taken out.
dOFF :At this position, power is cut off and the
engine stops. The key can be taken out.
eLOCK :At this position, the steering handlebar
is locked. The key can be taken out
《Locking Method》
Turn the steering handlebar left to the full and then
press to turn the ignition switch key to “LOCK”
position and the handlebar is locked.
《Unlocking Method》
Turn the key to “OFF” and the lock is released
automatically.
nCAUTION:
yAfter locking, turn the handlebar gently to make
sure that it is locked.
yDo not turn the ignition switch to “LOCK”
during riding, or the handlebar will be out of
control and cause accidents.
yDon‘t park your motorcycle at a place to hinder
the traffic.
c
d
e
-6-
(2) STARTER BUTTON
yRelease the steering handlebar lock before
starting the engine. Turn on the ignition switch
and then press the starter button. Make sure to
depress the gear shift pedal into the neutral
position to avoid engine damage.
nCAUTION:
yDuring engine running, do not push the starter
button to avoid engine damage.
yBefore starting the engine, please rebound the
side stand.
(3) HEADLIGHT SWITCH/ HORN BUTTON
zAt this position, the position light,
headlight, instrument lights and taillight go
out together.
P At this position, the position light, instrument
lights and taillight light together.
HAt this position, the position light, headlight,
instrument lights and taillight light together.
yWhen the ignition switch is turned “ON”, press
the horn button and the horn will sound.
yThe horn switch do not work when the ignition
switch is “OFF”.
y
-7-
(4) HEADLIGHT DIMMER SWITCH/
PASSING SIGNAL SWITCH
HI Switch to this position for using high beam.
LO When riding in downtown area or there is a
car coming from the opposite direction, use
low beam to avoid affecting the visibility of
coming cars.
PASSING When passing, if there are cars coming
from the opposite direction, press and
release the PASSING switch and the
headlight will wink to warn the
coming cars.
(5) TURN SIGNAL SWITCH
yThe turn signal switch do not work when the
ignition switch is “OFF”.
yWhen the winker lamp is used, both the winker
lamp on the panel will blink same time.
cÖFor turning to the right. dÕFor turning to
the left. ePush the turn signal switch button to
release it.
nCAUTION:
yThe turn signal light will not release
automatically. Be sure to reset it after use;
otherwise it may affect the traffic safety.
PASSING
c
d
e
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali KYMCO Motociclo
KYMCO
KYMCO Venox 250 Manuale utente
KYMCO
KYMCO G-Dink 125i Manuale utente
KYMCO
KYMCO XCITING 500 Manuale utente
KYMCO
KYMCO Quannon 150 Manuale utente
KYMCO
KYMCO Dink 50 Manuale utente
KYMCO
KYMCO K-XCT 125i Manuale utente
KYMCO
KYMCO 125 MOVIE S INJECTION Manuale utente
KYMCO
KYMCO X-Town 300 Manuale utente
KYMCO
KYMCO VISA R 110 Manuale utente
KYMCO
KYMCO Dink 50 Nota di rilascio
KYMCO
KYMCO DOWNTOWN 300i 2011 Manuale utente
KYMCO
KYMCO FILLY 50 Manuale utente
KYMCO
KYMCO MXU 300 - Manuale utente
KYMCO
KYMCO XCITING 500 Manuale utente
KYMCO
KYMCO CV3 Series Manuale utente
KYMCO
KYMCO Dink-R125 Manuale utente
KYMCO
KYMCO Venox 250 Manuale utente
KYMCO
KYMCO AGILITY300 Manuale utente
KYMCO
KYMCO K-PIPE 125 Manuale utente
KYMCO
KYMCO 125 ZING II QE - Manuale utente
