Kyocera FS-5800C Manuale utente
69
Care and Maintenance
Cleaning
Periodic cleaning of the printer is recommended. The frequency of cleaning is dependent
upon the environment in which the printer is used. You should clean the printer:
• At least once a month.
•When the printer experiences frequent media jams.
•When print quality has deteriorated.
■External
1
Turn the power OFF.
2
Clean all the covers with a soft cloth. Use any mild commercial
cleaner.
Caution:
Do not use benzine, thinner, aerosol cleaners, or any abrasive powder.
■Internal
When using isopropyl alcohol with a lint-free cloth, make sure that the alcohol is at least
90% pure, obtainable from your local pharmacy. (Do not use rubbing alcohol; it can
damage the printer.)
Cleaning the paper-pick rollers
1
Slide the media tray out (you do not have to remove it) to allow
access to the paper-pick rollers.
2
Open the left side cover.
3
Use the green handles to pull out the paper feeder.
70
Care and Maintenance
4
Gently rotate the paper-pick rollers 180°(the paper-pick rollers are
D-shaped) and wipe them with a lint-free cloth that has been
moistened with isopropyl alcohol.
5
Reinsert the paper feeder ( (1) ) and close the left side cover ( (2) ).
6
Slide the media tray back into place.
Note:
If you have an optional paper feeder installed, you may also need to clean the rollers
for the middle and lower media trays, which are accessed through the lower left side
cover.
Cleaning the home sensor
1
Open the printer’s front cover.
(1) (2)
71
Care and Maintenance
2
Remove the imaging unit:
(1)Loosen the two thumbscrews by turning them counterclockwise.
(2)Turn the lower green lever 180°counterclockwise.
(3)Grasping the front green handle, slide the imaging unit out until
it catches.
(4)Lift up the left green handle. Pull the imaging unit out of the
printer and cover it to protect it from light exposure.
Important:
Do not touch the green surface (the right side) or the black belt (the underside).
Finger prints may affect the print quality.
Safety Caution:
The imaging unit weighs approximately 6.5 kg (14.3 lbs.). Always use the handles
when lifting it.
Cautions:
• Do not expose the imaging unit to artificial light for more than 45 seconds; or you
may damage the unit. Never expose it to direct sunlight.
• Do not leave the printer’s front cover open for an extended period of time (for
example, several hours).
(1)
(1)(2)
Green surface
Black belt
(3)
(4)
72
Care and Maintenance
3
Use a dry, lint-free cloth to wipe the slot of the sensor.
4
Reinsert the imaging unit into the printer, holding it by its green
handles.
Match the arrow on the right side of the imaging unit with the arrow on the
printer, and slightly push the imaging unit into the printer. Then release the left
handle and push the unit in until it stops.
5
(1)Turn the lower green lever clockwise 180°to insert the unit
completely and to lock it.
(2)Tighten the two green thumbscrews by turning them clockwise.
(3)Close the front cover.
Sensor
Slot
(3)
(1)
(2)
(2)
73
Care and Maintenance
User Replaceable Components
When the printer panel indicates that a supply needs to be replaced, make sure that you
have replacement supplies on hand. The printer may continue to print until the supply is
completely used up; then it stops until you replace the indicated supply.
Printer component Printer panel message Average life*1
Toner developers 10,000 pages
Toner low (CMY)*2
TD-80x (
Colour
)
Change the colour toner developer soon.
12,000 pages
Replace Toner (Black)*2
TD-80K (Black)
Change the black toner developer now.
Colour imaging unit Monochrome
Warning IU-80 57,000 pages
Imaging unit or
Colour
Change the Imaging unit soon. 14,250 pages
Monochrome
Replace IU-80 60,000 pages
Imaging unit or
Colour
Change the Imaging unit now. 15,000 pages
*1These figures are based on an average of 5% coverage of the printable area and standard density
for any one colour. The frequency of replacement will vary depending on the complexity of the
prints and the percentage of coverage and print density.
*2The starter developers that are shipped with the printer have an average life of approximately
3,000 pages, based on an average of 5% coverage.
Note:
If you print with high density when Toner low is displayed, you may get faded
printout before Replace Toner is displayed.
74
Care and Maintenance
Printer component Printer panel message Average life
Fuser unit *1 28,500 pages
(Oil supply roll Warning FK-80
installed) Fuser KIT
Change the Fuser unit soon.
31,000 pages
Replace FK-80
Fuser KIT
Change the Fuser unit now.
Oil supply roll 15,000 pages
Warning OS-80
Oil supply roll
Change the Oil supply roll soon.
15,500 pages
Replace OS-80
Oil supply roll
Change the Oil supply roll now.
Transfer unit 80,000 pages
Warning TU-80
Transfer roller
Change the Transfer unit soon.
*1Transparencies, coated paper, and other specialty media will result in shortening the life of a
consumable. When replacing the fuser unit, replace the oil supply roll as well. Do not insert the
used oil supply roll into the new fuser unit.
75
Care and Maintenance
Clearing a Jam
■Clearing a media jam
If the printer has frequent media jams, make sure that you follow these guidelines:
• Always use high-quality plain paper and transparencies. Refer to pages 111 and later.
• Make sure that you load specialty media only in the multi-purpose tray and that you
set the media thickness switch to the correct setting for the media used.
If a media jam occurs, the printer panel reports “Paper Jam.” It is followed by one of the
letters A through E that correspond to the various sensors throughout the paper path.
The following illustration shows the locations of the sensors that report media jams
(A through E).
Jam at A
Jam at C
Jam at D
Jam at E
( ☞P. 76)
( ☞P. 80)
( ☞P. 84)
( ☞P. 86)
Jam at B
( ☞P. 79)
Paper feeder (option)
76
Care and Maintenance
■Jam at A
1
A
(1)Open the left side cover corresponding to the selected media
cassette.
(2)Remove the jammed media.
(3)Close the left side cover.
— OR —
(4)Remove the media cassette.
(5)Remove the jammed media from inside the printer.
(6)Reinsert the media cassette.
(7)Open and close the front cover to clear the error message from
the message display.
(1)
(2)
(4)
(5)
77
Care and Maintenance
(Paper feeder)
1
B
(1)Open the lower left side cover.
(2)Remove the jammed media.
(3)Close the lower left side cover.
— OR —
(4)Remove the selected media cassette (middle or lower media tray).
(5)Remove the jammed media from inside the printer.
(6)Reinsert the media tray.
(7)Open and close the front cover to clear the error message from
the message display.
(1)
(2)
(4)
(5)
78
Care and Maintenance
(Muti-purpose tray)
1
C
Remove the jammed media from the multi-purpose tray.
2
C
Open and close the front cover to clear the error message from the
message display.
Altri manuali per FS-5800C
2
Indice
Altri manuali Kyocera Stampante
Kyocera
Kyocera ECOSYS M2030dn Manuale utente
Kyocera
Kyocera TASKalfa MA4500ci Manuale utente
Kyocera
Kyocera Ci1000 Manuale del prodotto
Kyocera
Kyocera FS FS-C8500DN Manuale utente
Kyocera
Kyocera ECOSYS FS-3920DN Manuale utente
Kyocera
Kyocera FS-1010 Manuale utente
Kyocera
Kyocera ECOSYS M2635dw Manuale di istruzioni
Kyocera
Kyocera FS-3700 Manuale utente
Kyocera
Kyocera Mita FS-1900 Manuale utente
Kyocera
Kyocera FS-2000D Manuale del proprietario
Kyocera
Kyocera ECOSYS MA4500ifx Manuale utente
Kyocera
Kyocera KM-4230 Manuale
Kyocera
Kyocera KM-6230 Manuale operativo e di manutenzione
Kyocera
Kyocera KM-3650W Guida
Kyocera
Kyocera FS-1100 Manuale utente
Kyocera
Kyocera ECOSYS M8130cidn Manuale utente
Kyocera
Kyocera ECOSYS P6230cdn Manuale utente
Kyocera
Kyocera ECOSYS FS-3140MFP Manuale utente
Kyocera
Kyocera FS-1800 Manuale utente
Kyocera
Kyocera ECOSYS P4140dn Manuale utente
