Laguna Tools DAKE 33-672 Manuale utente

Dake Corporation Phone: 800.937.3253 www.dakecorp.com

1809 Industrial Park Dr

Grand Haven, MI 49417

150 TON ELECTRIC TIRE PRESS

Model 33-672

INSTRUCTIONAL MANUAL

WARNING!

Read and understand all instructions and responsibilities before operating. Failure to follow safety

instructions and labels could result in serious injury.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 1 REV032022

TABLE OF CONTENTS

SAFEGUARDING THE POINT OF OPERATION..........................................................2

SPECIFICATIONS ........................................................................................................ 3

SAFETY........................................................................................................................ 4

SET UP.........................................................................................................................5

OPERATION.................................................................................................................5

MAINTENANCE............................................................................................................6

LUBRICATION..................................................................................................... 6

REPLACING HYDRAULIC OIL............................................................................6

TROUBLESHOOTING..................................................................................................6

ELECTRICAL DIAGRAM ..............................................................................................8

HYDRAULIC DIAGRAM................................................................................................9

EXPLODED VIEWS & PARTS LISTS .........................................................................10

ORDERING INFORMATION....................................................................................... 16

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 2 REV032022

SAFEGUARDING THE POINT OF OPERATION

ANSI B11.2 - Hydraulic Power Presses -

Safety Requirements for Construction, Care, and Use

It is important that Dake press users have a clear understanding of their responsibility involving the care and

use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that

Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for

a more complete understanding of their responsibilities.

ANSI B11.2 states the following, relative to point of operation safeguarding:

“Normally, only the employer (press user) can determine the requirements of the press productions system

components, including the dies and methods for feeding. Therefore, the employer is ultimately responsible to

designate and provide the point-of-operation safeguarding system.”

The standard also discusses additional responsibilities of the employer. Some of the key responsibilities are:

•The employer is responsible for the safety, use, and care of the hydraulic power press production system.

•The employer is responsible to consider the sources of hazards for all tasks to be implemented on the

hydraulic power press production system.

•The employer is required to eliminate or control identified hazards in the scope of their work activity.

•The employer is responsible for the training of personnel, caring for, inspecting, maintaining, and operating

hydraulic press production systems to ensure their competence.

•The employer is responsible to provide and ensure that point-of-operation safeguarding is used, checked,

maintained, and where applicable, adjusted on every production operation performed on a press

production system.

A complete and current copy of the ANSI B.11.2 standard can be obtained by contacting the following:

American National Standards Institute

1430 Broadway

New York, NY 10018

AMT – The Association For Manufacturing Technology

7901 Westpark Drive

McLean, VA 22102

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 3 REV032022

SPECIFICATIONS

Model Number

933672

Capacity

150 Ton

Horsepower

10 HP

Voltage

220V/440V 3-Phase

Stroke

18”

Ram Travel

18” w/ limit switch

Head Channel Travel

15”

Width between Uprights

36”

Max Daylight

36”

Platen Diameter

25”

Ram Advance Speed

17 IPM

Return Speed

Gravity

Base

57” x 43”

Height

80”

Weight

3,600 lbs.

In the space provided record the serial number and model number of the machine. This information is

only found on the black and gold Dake tag shown below. If contacting Dake this information must be

provided to assist in identifying the specific machine.

Serial No.

Model No.

Install Date:

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 4 REV032022

SAFETY

This is the safety alert symbol. When you see this symbol on your press be alert to the

potential for personal injury.

Employer is responsible to perform a hazard/PPE assessment before work activity.

Follow recommended precautions and safe operating practices.

•Carefully read all safety messages in these instructions and on your press safety signs.

Keep safety labels in good condition. Replace missing or damaged safety labels.

•Do not alter this press from its original design.

•Do not make repairs or adjustments to any hydraulic system unless you are competent or

working under competent supervision.

•Only use Dake original parts.

•This machine is intended to be operated by one person. This person should be conscious of

the press ram movement not only for themselves but also for persons in the immediate area of

the machine.

Label Part No.

84401

Label Part No.

84487

Label Part No.

84395

Label Part No.

84399

Label Part No.

76462

Label Part No.

84396

Label Part No. 63565

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 5 REV032022

SET UP

1. Anchor press to floor using 5/8” holes on the base angles of the press.

2. Have an electrician connect starter to power source, pump can rotate in either direction.

CAUTION: Only a licensed electrician that follows local and state laws is authorized to

make an electrical connection to this machine.

3. Remove 3/4” pipe plug and 1/8” pipe plug from side of reservoir, fill with mobile DTE 26 or

equivalent hydraulic oil thru 3/4” pipe hole. Fill with oil it reaches the 1/8” pipe tapped hole.

4. CAUTION: Strainer or filter should be used to make sure no contaminants get into

reservoir. Replace both pipe plugs.

Oil capacity: 7 Gallons

OPERATION

RAM MOVEMENT

To raise the ram, turn the release valve handle clockwise, so that the release valve is closed. Then

press the raise button to raise the ram. The ram will raise as long as the operator presses the button.

Ram movement can be stopped at any time by releasing the raise button.

After the work has been contacted, the press will continue to build pressure as the ram advances,

until the press reaches its maximum tonnage. At this point the relief valve will open, allowing oil to

return to the reservoir.

To release pressure and lower the ram, turn release valve handle counterclockwise to open the

release valve. This permits the oil to return to the reservoir and the ram to lower.

HOIST

The hoist hand crank is provided to raise and lower the upper platen to the proper work height. To

change the vertical position of the upper platen, sufficient tension must first be applied to the hoisting

cable to permit removal of table pins. Then the upper platen may be raised or lowered to the desired

position. All table pins must be inserted once desired position is achieved.

CAUTION: Be sure all the table pins are in place and there is slack in the cable before

applying any pressure. It is advisable to lower the top platen opposed to running the lower

platen to the end of its stroke.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 6 REV032022

MAINTENANCE

LUBRICATION

•Keep all working parts of the press well-oiled for easier operation.

•Keep a light film of oil over the entire surface of the ram to prevent rust.

REPLACING HYDRAULIC OIL

Recommended to replace hydraulic oil every 6 months of machine use.

*Amount needed may vary dependent on machine use*

TROUBLESHOOTING

CAUTION:

A. Oil Leaks around the Piston

1. Oil above the piston leather: If rated stroke of the press is exceeded repeatedly by running

the piston past rated stroke, bypass hole in the side of the cylinder run bypass line that

connects above the piston leather. Eventually enough oil may accumulate so that when the

piston is raised to the top of it’s stroke, oil is forced out between the piston and piston guide.

This can be remedied by disconnecting the bypass tube line from the cylinder, then raising

the piston slowly, about 2-1/2” less than it’s rated stroke (rated stroke: 18”) allowing the oil

above the piston cap to overflow out the bypass hole into a clean bucket. Replace tube line.

Oil may be put back into reservoir by removing the fill plug on the top of the reservoir.

B. Press does not hold pressure

1. Loosen tube connections, check all connections and tighten any loose tube nuts.

2. Dirt under release ball.

Too correct this condition, remove the release valve rod packing nut, packing, and ball. Clean

out the valve seat, reseat the valve ball using brass rod as a drift, tapping lightly.

Reassemble valve.

If this occurs frequently, the oil should be drained from the reservoir, then flush the reservoir

to remove any dirt or contaminants. Refill reservoir with mobile DTE 26 or equivalent

hydraulic oil. Oil must be filtered carefully to removed and contaminants. Refill reservoir with

oil. See “SET UP” section of manual for instructions.

3. Worn leather cup

If neither of the previous conditions seem to be the cause of the pressure not holding the

piston leather may be worn or damaged. To inspect leather, remove the lower platen, then

remove cap screws that bolt the piston guide to the cylinder flange. Piston and piston guide

may be then listed out of the cylinder and inverted, the leather now can be inspected and

replaced in necessary. Reassemble the press, take care not to damage the lip of the leather

cup as it enters the cylinder.

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 7 REV032022

C. Press will not develop rated tonnage

1. Dirt under release valve ball. See B-2, previously.

2. Worm leather cup. See B-3, previously.

3. Relief valve set low.

The relief valve has been set at the factory to bypass oil back to the reservoir when the press

reaches its rated capacity. However, if the press does not develop rated tonnage and the 2

above conditions have been checked, the relief valve may need readjusting. To do this

remove the 1/4” pipe plug in the connector block. The valve adjustment screw should now be

accessible and should be adjusted with a 7/32” hex wrench. To increase the setting, turn the

adjustment screw clockwise, only adjust screw in small increments before testing tonnage.

Be careful not to adjust the valve over its rated tonnage or maximum operating pressure

(6000PSI).

CAUTION: Never exceed 150 tons or operating pressure of 6000 PSI

D. No ram movement

1. Release valve open.

Be sure release valve is firmly closed when operating press.

2. Insufficient oil

Check oil level in the reservoir when the ram is complete down (rest position). Remove 1/8”

pipe plug on side of reservoir. Oil level should reach this hole.

3. Pump loses its prime

Make sure all intake connections are tight.

Check to make sure there is enough oil in the reservoir

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 8 REV032022

ELECTRICAL DIAGRAM

Drawing No: 87489

Dake Corporation

1809 Industrial Park Dr

Grand Haven, MI 49417

www.dakecorp.com

933672 9 REV032022

HYDRAULIC DIAGRAM

With pump (2) running and valve (4) centered pump (2) delivery is returned to reservoir (7).

For Pressing: valve (4) is shifted, directing pump (2) delivery to bottom of cylinder (6). Ram advances until

contacting work, then builds pressure to rated capacity of the press, when press hits capacity then relief valve

(3) opens, returning pump delivery to reservoir (7).

For Release: With valve (4) centered, and piston in extended position, release valve (5) is opened, releasing

pressure from bottom of cylinder (6). Gravity returns ram to down position.

Item

Part Name

Part No.

Qty

Motor

70901

Pump

29608A

Relief Valve

within 29661

Manual 3-Way Valve

29661

Release Valve

710557

Workhead

707594A

Reservoir (7 gallons)

47343

Gauge

71268

Drawing No: 80490

Indice

Altri manuali Laguna Tools Utensili elettrici

Laguna Tools

Laguna Tools DAKE Y Manuale utente

Laguna Tools

Laguna Tools DAKE 1-1/2C Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools Platinum Series Manuale utente

Laguna Tools

Laguna Tools MRS5000-0280 Manuale utente

Laguna Tools

Laguna Tools DAKE SB-25V Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools DAKE 4 Manuale utente

Laguna Tools

Laguna Tools PP16 XC Pro Manuale utente

Laguna Tools

Laguna Tools DAKE Force 10DA Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools Dake SB-32V Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools DAKE 00 Manuale utente

Laguna Tools

Laguna Tools DAKE X Manuale utente

Laguna Tools

Laguna Tools Dake Force 150 Manuale utente

Laguna Tools

Laguna Tools MJOPL104200 Manuale utente

Laguna Tools

Laguna Tools T800i Manuale utente

Laguna Tools

Laguna Tools PP16 XC Pro Manuale utente

Laguna Tools

Laguna Tools MJO6405-0800 Manuale utente

Laguna Tools

Laguna Tools Dake 6-275 Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools DAKE 33-493 Manuale utente

Laguna Tools

Laguna Tools DAKE 75H Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools DAKE Force 50DA Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools DAKE 1-1/2 Manuale operativo e di manutenzione

Laguna Tools

Laguna Tools P12 10 Manuale utente

Laguna Tools

Laguna Tools SHEARTEC II Manuale utente

Laguna Tools

Laguna Tools Platinum Series Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale