Lanpro SW2400S Manuale utente
www.lanpro.com
SW2400S
24-Port SFF 10/100Mbps
Fast Ethernet Switch
Up to 200Mbps full duplex
bandwidth capability
for high speed data
processing
Innovative Energy-Smart
technology saves power
up to 70%
Hassle free setup,
no configuration
required
200
Mbps
Small Form Factor,
can be installed on a
shelf or rack mount.
LPSW2400S_UG_ENB01W
Model: LP-SW2400S
User Guide
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
2
COPYRIGHT & TRADEMARKS
Specications are subject to change without notice. LanPro is a
registered trademark of LanPro Inc. Other brands and product names
are trademarks or registered trademarks of their respective holders.
No part of the specications may be reproduced in any form or by
any means or used to make any derivative such as translation,
transformation, or adaptation without permission from LanPro Inc.
Copyright © 2015 LanPro Inc. All rights reserved.
www.lanpro.com
Mark Warning
This is a class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
3
CONTENTS
Package Contents ...................................................................... 4
Chapter 1 Product Introduction...................................... 5
1.1 Product Overview ............................................ 5
1.2 Features .......................................................... 5
1.3 IEEE 802.1p QoS ............................................ 6
1.4 Priority levels Table .......................................... 7
Chapter 2 Identifying External Components ................ 7
2.1 Front Panel ...................................................... 7
2.2 Rear Panel ...................................................... 8
Chapter 3 Installation ..................................................... 8
3.1 Precautions ..................................................... 8
3.2 Installation ....................................................... 9
3.2.1 Desktop Installation ............................... 9
3.2.2 Rack Installation .................................... 10
3.3 Connect to Ground .......................................... 12
3.4 Power on ......................................................... 13
Appendix A: Specications ................................................ 14
Appendix B: Troubleshooting ............................................ 15
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
4
Package Contents
The following contents should be found in your box:
a.- One LP-SW2400S switch .
b.- One power cord .
c.- Installation Guide.
d.- 1 Set of screws for attaching two “L” brackets used for
mounting on 19 inch racks.
Make sure that the package contains the above items. If any
of the listed items are damaged or missing, please contact
with your distributor.
Note:
Figure 1. Package Contents
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
5
Chapter 1: Product Introduction
Product Overview
Features
1.1
1.2
This chapter describes the features of the model of LP-SW2400S 24-port
10/100Mbps Fast Ethernet Switch.
LP-SW2400S 24-port switch provides 24 10/100Mbps Auto-Negotiation
RJ45 ports. Each port of the LP-SW2400S supports auto MDI/MDI-X
function, eliminating the need for crossover cables or Uplink ports. The
switch is Plug-and-Play and any port can be simply plugged into a server, a
hub or a switch by using straight cable or crossover cable.
The LP-SW2400S 24-port 10/100Mbps Fast Ethernet Switch provides you
with a low-cost, easy-to-use, high-performance, seamless and standard
upgrade to improve your old network to a 100Mbps network. It will boost
your network performance up to full duplex data transfer.
The LP-SW2400S switch supports Energy-Smart technology, with power
saving features to help make your network environmentally friendly without
compromising performance. The switch automatically powers down ports
that have no link and budgets power output for different Ethernet cable
lengths. It can also reduce the power consumption in idle mode or with low
trafc mode.
►Complies with IEEE802.3, IEEE802.3u, IEEE802.3az, IEEE
802.1p standards.
►24 10/100Mbps Auto-Negotiation RJ45 ports supporting Auto-
MDI/MDIX.
►Supports IEEE802.3X ow control for full-duplex mode and
backpressure for half-duplex mode.
►Supports IEEE 802.1p QoS.
►Supports power saving features, with Energy-Smart Technology.
►LED indicators for monitoring power, link and activity.
►Desktop or 19 Inch Rack mountable 11.6 Inch wide Small Form
Factor (SFF) Steel case.
►Internal power supply.
►Plug and Play
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
6
IEEE 802.1p QoS
1.3
The LP-SW2400S switch supports 802.1p priority queuing Quality of
Service (QoS), which is an implementation of the IEEE 802.1p standard.
With 802.1p QoS function, you can reserve bandwidth for important
functions that require a large bandwidth or have a high priority, such as
VoIP (Voice-over Internet Protocol), web browsing applications or video
conferencing. The switch has separate hardware queues on every physical
port which packets from various applications are mapped to and assigned
a priority to. The illustration below shows how 802.1p priority queuing is
implemented on the switch.
The switch has four priority levels labeled TC0, TC1, TC2 and TC3. The
untagged packets and the eight IEEE 802.1p priority tags dened by the
standard are mapped to the four level queues used on the switch. TC3
has the highest priority of the four priority level queues while TC0 has the
lowest priority on the switch. The untagged packets and eight priority tags,
specied in IEEE 802.1p are mapped to the switch’s priority tags as follows:
The switch uses WRR (Weighted Robin Round) for scheduling. WRR
queue-scheduling algorithm schedules all the queues in turn and every
queue can be assured of a certain service time. The default weight value of
TC0, TC1, TC2 and TC3 is 1:2:4:8.
Figure 2. Mapping QoS on the Switch
►The untagged packets, packets with priority tag 1 and 2 are
assigned to the switch’s TC0 level queue.
►Packets with priority tag 0 and 3 are assigned to the switch’s
TC1 level queue.
►Packets with priority tag 4 and 5 are assigned to the switch’s
TC2 level queue.
►Packets with priority tag 6 and 7 are assigned to the switch’s
TC3 level queue.
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
7
Priority Levels Table
1.4
PCP Priority Acronym Trafc Types
1 0 (Lowest) BK Background
01 BE Best Effort
2 2 EE Excellent Effort
3 3 CA Critical Applications
4 4 VI Video, < 100 ms latency and jitter
5 5 VO Voice, <10ms Latency and Jitter
6 6 IC Internetwork Control
77 (Highest) NC Network Control
Figure 3. Switch Front Panel Sketch
►Power LED: This indicator will light solid green when the switch
powers up. If the LED is not lit, please check the power supply and
connection.
►Link/Act LED: The LED indicates Link/Active status. The
corresponding LED indicator will light solid green when connected to
a network device. It ashes green when data is being transmitted or
received on the working connection.
Chapter 2: Identifying External Components
This chapter describes the front panel, rear panel and LED indicators of
the switch.
Front Panel
2.1
The front panel of LP-SW2400S consists of switch model, switch LED
indicators, and 24 10/100Mbps RJ-45 ports.
The LED indicators include Power, Link/Act LED indicators, which are used
for monitoring and pre-troubleshooting of the switch. The following section
shows the LED indicators of the switch along with explanation of each
indicator.
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
8
Chapter 3: Installation
To ensure a long-term and stable performance of the switch, please pay
attention to the following before the installation.
Precautions
1) Safety Requirements:
3.1
▪Before cleaning the switch, cut off the power supply. Do not
clean it by the waterish cloth, and never use any other liquid
cleaning method.
▪Take waterproof measures during storage, transportation and
operation of the equipment.
▪Use only the power cord provided with the switch.
▪Make sure the voltage of the power supply meets the
requirement of the input voltage of the switch.
▪Do not push any objects into the openings of the switch.
▪Ensure the vent hole is well ventilated and unblocked.
▪Do not open or remove the cover of the switch.
Figure 4. Switch Rear Panel Sketch
►Grounding Terminal: LP-SW2400S already comes with Lightning
Protection Mechanism. You can also ground the switch through the
PE (Protecting Earth) cable of AC cord or with Ground Cable. For
detail information, please refer to section 3.3 Connect to Ground.
►AC Power Socket: Connect the female connector of the power cord
here, and the male connector to the AC power outlet. Please make
sure the voltage of the power supply meets the requirement of the
input voltage.
Rear Panel
2.2
The rear panel of LP-SW2400S features a power socket and a Grounding
Terminal (marked with ).
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
9
When you choose a location for the switch, please follow these
guidelines:
2) Location Requirements:
▪Install the switch on a at and stable surface that can support
the entire weight of the switch with all ttings.
▪Locate the switch far from strong electromagnetic eld
generators (such as motors), vibration, dust, and direct
exposure to sunlight.
▪To ensure adequate air ow around the switch, at least 10 cm
(4 inches) of space at the front and rear of the switch is needed
for ventilation.
▪Make sure that the switch will be accessible and that the
cables can be easily connected.
▪Position the switch away from water and moisture sources.
Be sure to provide an acceptable temperature and humidity
operating environment.
This switch can be either installed on the standard 19-inch mountable rack
or located on the desktop.
To install the switch on the desktop, please follow the steps:
Installation
Desktop Installation
3.2
3.2.1
1) Set the switch on a at surface strong enough to support the
entire weight of the switch with all ttings.
2) Remove the adhesive backing papers from the rubber feet.
3) Turnover the switch and attach the supplied rubber feet to the
recessed areas on the bottom at each corner of the switch.
Please unplug the power cord before installing or
removing the switch.
Caution:
LP-SW2400S ▪ 24-port 10/100Mbps Fast Ethernet Switch ▪ User Guide ▪ www.lanpro.com
10
To install the switch in an EIA standard-sized, 19-inch rack, follow the
instructions described below:
Rack Installation
3.2.2
1) Secure the supplied rack-mounting brackets to each side of
the switch with supplied screws, as illustrated in the following
gure.
4) Upturn the switch and connect it to the network devices while
keep enough ventilation space around.
5) Connect the switch to power source with the provided power
cord.
Please avoid any heavy thing placed on the switch.
Caution:
Figure 5. Attaching Rubber Feet
Indice
Altri manuali Lanpro Interruttore
