Larson Electronics HALP-48-2L-LED-DNMS Manuale utente

HALP-48-3L-LED-DNMS

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

84 Watt Class 1 Division 2 LED for Corrosion

Resistant Requirements - Motion + Day/Night Sensor

Instruction Manual

Thank you for your purchase of the Larson Electronics HALP-48-2L-LED-DNMS Corrosion Resistant light

fixture. Please follow the steps below in order to operate and maintain this product.

WARNING!

1. TO PREVENT RISK OF ELECTRICAL SHOCK DEACTIVATE/DISCONNECT POWER SUPPLY BEFORE

INSTALLING, MAINTAINING OR RELAMPING FIXTURE.

2. TO REDUCE RISK OF FIRE OR EXPLOSION, DO NOT INSTALL WHERE THE MARKED OPERATING

TEMPERATURE EXCEEDS THE IGNITION TEMPERATURE OF THE HAZARDOUS ATMOSPHERE(S).

3. THIS FIXTURE SHOULD BE INSTALLED BY QUALIFIED TECHNICIANS IN STRICT ACCORDANCE WITH THE

NATIONAL ELECTRICAL CODE AND ANY LOCAL REQUIREMENTS.

INSTALLATION

1. Install fixture to surface with preinstalled mounting brackets (mounting hardware not included).

2. Remove lens by releasing 8 latches that secure the lens. Start with one side and continue to the other side.

Keep hold of the lens as this will be free once brackets are removed.

3. There are clips on both sides holding the ballast tray to the fixture base. Pinch the clips on both sides to

release the tray and access the underside.

4. Electrical voltages and frequency are listed on the product nameplate for reference. This fixture comes

preconfigured to work with the selected voltage. Check product nameplate to ensure proper voltage to the

fixture before energizing!

5. For supply connections use conductors suitable for min. 90° C.

6. Connect internal wires per wiring diagram, and according to NEC requirements.

7. Replace the ballast tray until the clips snap in to secure it.

8. Replace lens and secure all 8 latches.

To replace lamps, remove the lens from the fixture (step 2) and rotate each lamp until they can be slid out from

each connection point. Replace with matching lamp and reverse the process.

MAINTENANCE

Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by

the environment and frequency of use. It is recommended that inspection be performed a minimum of once a year.

WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND

MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND

COMPETENT ELECTRICIAN.

1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible

problem and should be thoroughly investigated and repaired as necessary.

2. Inspect contacts for signs of wear and replace if necessary.

3. Clean exterior surfaces making sure nameplates remain legible.

If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This

condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the

proper replacement part(s) before continuing service.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

HALP-48-3L-LED-DNMS

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MOTION + DAY/NIGHT SENSOR

The sensor can be configured to work for the environment installed. Features such as Sensitivity, Time on, and

LUX can be configured. De-energize fixture prior to making adjustments in order for them to take effect!

DIP SWITCHES

IMPORTANT: persons or objects moving towards the sensor are detected best.

NOTE: The high frequency of the output of this sensor is <10Mw – that is just one 100th of the transmission

power of a mobile phone or the output of a microwave oven.

Detection Area

Detection area can be reduced by selecting the combination on the DIP

switches to fit precisely each application.

Hold Time

Refers to the time period the lamp remains illuminated after no motion is

detected.

Daylight Sensor

The sensor can be set to only allow the lamp to illuminate below a defined

ambient brightness threshold. When set to Disable mode, the daylight sensor

will switch on the lamp when motion is detected regardless of ambient light

level. 30lux, 50lux, 100lux,: twilight operation, 5lux, 15lux: darkness operation

only.

These instructions may not cover all details or variations of this product for your equipment or installation requirements. Should further

information not covered by these instructions be required, please contact Larson Electronics at 1-800-369-6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Indice

Altri manuali Larson Electronics Apparecchio di illuminazione

Larson Electronics

Larson Electronics EPL-AMB-150LED-250 Manuale utente

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM Manuale utente

Larson Electronics

Larson Electronics ATEX-EHL-1123-LED-50-EPP Manuale utente

Larson Electronics

Larson Electronics EPL-LP-12-LED-SFC.LP Manuale utente

Larson Electronics

Larson Electronics EPLC2-LB-40LED-RT-CM Manuale utente

Larson Electronics

Larson Electronics HALD-24-1X100LED-DIMM Manuale utente

Larson Electronics

Larson Electronics EPLC-48-432 Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-400W Manuale utente

Larson Electronics

Larson Electronics EPL-HB-150LED-PND Manuale utente

Larson Electronics

Larson Electronics EPLC2-LB-50LED-RT-CM Manuale utente

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Manuale

Larson Electronics

Larson Electronics RCL360-LED-40 Manuale utente

Larson Electronics

Larson Electronics EPL-16BS-1X150LED-X24I-C1D1-200 Manuale

Larson Electronics

Larson Electronics GVP-48-2L-LED-G3 Manuale utente

Larson Electronics

Larson Electronics GAU-HB-12L-LED-WP-WCM Manuale utente

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-SP0122 Manuale utente

Larson Electronics

Larson Electronics EPL-PT-150LED-RT-100-EPP Manuale utente

Larson Electronics

Larson Electronics IND-AHC-CR-12-UVC-R1-120V Manuale utente

Larson Electronics

Larson Electronics LED T Series Manuale utente

Larson Electronics

Larson Electronics EPL-AMB-150LED-200 Manuale utente

Larson Electronics

Larson Electronics HAL-PT-LED-CPR-C-100 Manuale utente

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-ASM-JB2-40C-BCE Manuale utente

Larson Electronics

Larson Electronics EPL-MBC-1MLED-2023 Manuale

Larson Electronics

Larson Electronics CL1B-SS-PM-1227 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente