Larson Electronics HALS-48-2L-LED Manuale utente

HALS-EMG-48-2L-LED

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Hazardous Location LED Lighting

4' 2 Lamp Fixture - LED Bulb - Multi-voltage - C1D2 & C2D2

Instruction Manual

Thank you for your purchase of the Larson Electronics HALS-48-2L-LED Hazardous Location LED Light. Please follow

the steps below in order to operate and maintain this product.

WARNING!

1. TO PREVENT RISK OF ELECTRICAL SHOCK DEACTIVATE/DISCONNECT POWER SUPPLY BEFORE

INSTALLING, MAINTAINING OR RELAMPING FIXTURE.

2. DO NOT INSTALL WHERE THE MARKED OPERATING TEMPERATURE EXCEEDS THE IGNITION

TEMPERATURE OF THE HAZARDOUS ATMOSPHERE(S). KEEP TIGHTLY CLOSED WHEN IN OPERATION.

3. THIS FIXTURE SHOULD BE INSTALLED BY QUALIFIED TECHNICIANS IN STRICT ACCORDANCE WITH THE

NATIONAL ELECTRICAL CODE AND ANY LOCAL REQUIREMENTS.

INSTALLATION

This fixture can be installed directly to any flat surface using the mounting brackets provided. For installation on structural

members like beams, angles or channels, it may be necessary to install beam clamps on the mounting brackets.

1. Install fixture to mounting surface at mounting locations (mounting hardware not included).

2. For supply connection, use wire suitable for at least 90°C

3. Connect black lead to the incoming line lead, white lead to incoming neutral and green lead to incoming ground lead.

Voltage must match product label!

4. Use the wiring diagram printed on the ballast label for reference.

To change lamp, release latches to remove front lens from fixture. Keep hold of lens when removing!

Remove old lamps and replace with compatible lamps matching fixture ratings. Tighten latches.

MAINTENANCE

Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by

the environment and frequency of use. It is recommended that inspection be performed a minimum of once a year.

WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND

MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND

COMPETENT ELECTRICIAN.

1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible

problem and should be thoroughly investigated and repaired as necessary.

2. Inspect contacts for signs of wear and replace if necessary.

3. Clean exterior surfaces making sure nameplates remain legible.

If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This

condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the

proper replacement part(s) before continuing service.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

These instructions may not cover all details or variations of this product for your equipment or installation requirements.

Should further information not covered by these instructions be required, please contact Larson Electronics at 1-800-369-

6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

HALS-EMG-48-2L-LED

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

EMERGENCY BACKUP BALLAST OPERATION

During normal operation, AC power is supplied to the ballast through the backup micro inverter and the inverter charges

the battery. Connecting the inverter wires (red and white) enables the emergency circuit and supplies power to the

control/monitor circuit. The backup micro inverter detects AC input voltage (120-277V AC) and automatically set the

output voltage during emergency operation.

When AC power fails, the backup micro inverter automatically switches to emergency mode, keeping the load illuminated

for a minimum of 90 minutes. When AC power is restored, the backup micro inverter returns to charge mode to recharge

the battery. The backup micro inverter consists of a low- battery voltage disconnect which is reset when AC power is

restored. The unit can also detect an abnormal load condition (open or shorted load) during emergency mode operation

and will protect the inverter from damage.

Indice

Altri manuali Larson Electronics Apparecchio di illuminazione

Larson Electronics

Larson Electronics HAL-RSLED-240W Manuale utente

Larson Electronics

Larson Electronics EPLC2-BS-70LED-100 Manuale

Larson Electronics

Larson Electronics RCL360-LED-40 Manuale utente

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Manuale

Larson Electronics

Larson Electronics HALP-48-2L-LED-DNMS Manuale utente

Larson Electronics

Larson Electronics EPL-QP-1X150-100 Manuale utente

Larson Electronics

Larson Electronics EPL-AMB-150LED-200 Manuale utente

Larson Electronics

Larson Electronics EPLC2-24-50LED Manuale utente

Larson Electronics

Larson Electronics LED25WRE-LENSCOVER Manuale utente

Larson Electronics

Larson Electronics IND-AHC-CR-12-UVC-R1-120V Manuale utente

Larson Electronics

Larson Electronics EPLC2-WPLED-100W-RT Manuale utente

Larson Electronics

Larson Electronics HALD-24-1X150LED-V3-DIMM Manuale utente

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT Manuale utente

Larson Electronics

Larson Electronics LED T Series Manuale utente

Larson Electronics

Larson Electronics GVP-48-2L-LED-G3 Manuale utente

Larson Electronics

Larson Electronics EPLC2-LB-40LED-RT-CM Manuale utente

Larson Electronics

Larson Electronics HAL-PRM-150W-LED-100 Manuale utente

Larson Electronics

Larson Electronics WAL-QP-4XWP60E-25-1227 Manuale utente

Larson Electronics

Larson Electronics LEDWL-STRB-RED-1227 Manuale utente

Larson Electronics

Larson Electronics EPL-PM-1X30LED-120XLV-100 Manuale

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM Manuale utente

Larson Electronics

Larson Electronics ATEX-EPL-TL-3X10W-C Manuale utente

Larson Electronics

Larson Electronics EPL-HB-3X150LED-RT Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-4L Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente