Larson Electronics EPLC2-LED-50W-RT-JB5 Manuale utente

EPLC2-LED-50W-RT-JB5

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

50W Explosion Proof LED Flood Light Fixture

C1D2, C2D1/C2D2 - Serviceable Junction Box - Cord

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a

conventional HID luminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any

nominal 100-277V AC 50/60 Hz or 11-25 Volts AC/DC power supply (depending on model) without

any variation in light output.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected

and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous

Atmosphere.

Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

For supply connections, use wire rated for at least 110°C

Recommended mounting height is 25-40 feet.

MOUNTING

This fixture offers an adjustable surface mounting system that allows this fixture to be mounted to any

flat surface including walls and ceilings. A single ½-13 bolt is used to mount the fixture to the

surface.

MOUNTING HOLE

ADJUSTMENT

SCREW

TIGHTEN ADJUSTMENT SCREW

ONCE IN DESIRED ANGLE

EPLC2-LED-50W-RT-JB5

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected voltage, and beam

angle. Position device near work area for operation. Run cable to

nearby power source. Insert and twist-lock explosion-proof plug

into a compatible receptacle within the hazardous environment.

See plug operation below.

PLUG OPERATION

Electrical connection between plug and compatible receptacle is

accomplished after plug fully inserts into receptacle and rotated

clockwise.

1. Lift receptacle door and locate polarization on mating plug

pin and receptacle face. Insert plug straight all the way into

receptacle until it cannot go further.

2. Rotate plug clockwise limit (37º), this closes internal

contacts and completes circuit. This also mechanically

locks plug into receptacle so it cannot be pulled out.

3. To remove plug, push plug inward and turn to

counterclockwise, pull plug straight out.

Follow all applicable NEC, local, and state electrical codes.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool

down before performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens

will void the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend

routine checks to be made on a yearly basis. Frequency of use and environment should

determine this. It is recommended to follow an Electrical Preventive Maintenance Program

as described in NFPA 70B: Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric

performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use

mild soap or a liquid cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions

or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE.

DAMAGE FROM IMPROPER

VOLTAGE MAY VOID

WARRANTY.

Indice

Altri manuali Larson Electronics Attrezzatura di illuminazione

Larson Electronics

Larson Electronics SLEDB-110V-MS Manuale utente

Larson Electronics

Larson Electronics MMLP-150LED-RT-12P Manuale utente

Larson Electronics

Larson Electronics LEDHWP-900-DNMS Manuale utente

Larson Electronics

Larson Electronics LEDSB-3XQF12V-1227-WF-3XKT Manuale di istruzioni per l'installazione

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Manuale utente

Larson Electronics

Larson Electronics WAL-ML-2XM-3G Manuale utente

Larson Electronics

Larson Electronics EPP-3P4W-30A-N7 Manuale utente

Larson Electronics

Larson Electronics HAL-MB-185LED-CPR-100 Manuale utente

Larson Electronics

Larson Electronics GSLEDIP6-C1D2 Manuale utente

Larson Electronics

Larson Electronics C1D1-2 Manuale utente

Larson Electronics

Larson Electronics EPL-HB-2X150LED-RT Manuale utente

Larson Electronics

Larson Electronics EPL-FL1524-LED-100 Manuale utente

Larson Electronics

Larson Electronics EPL-HB-150LED-RT Manuale utente

Larson Electronics

Larson Electronics SPLED-QP-1X10WRE Manuale utente

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manuale utente

Larson Electronics

Larson Electronics EPL-FL1524-25-1523 Manuale utente

Larson Electronics

Larson Electronics EPL-48-2L-T12VHO Manuale utente

Larson Electronics

Larson Electronics MMLP-1MLED-12P Manuale utente

Larson Electronics

Larson Electronics EPLC2-PT-2X150LED-RT Manuale utente

Larson Electronics

Larson Electronics EPL-EMG-LED-100W-RT Manuale utente

Larson Electronics

Larson Electronics HAL-RSL Series Manuale utente

Larson Electronics

Larson Electronics HALP-24-2L-LED-2XH Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Manuale utente

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Manuale di istruzioni

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente