Larson Electronics SLEDB-110V-MS Manuale utente

SLEDB-110V-MS

Larson Electronics, LLC

Phone: (877)348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

1 of 5

Class II Strobe Light with Motion Sensor

110-120V AC - 54 Flashes Per Minute - 5 Color Options

Instruction Manual

Thank you for your purchase of the Larson Electronics SLEDB-110V-MS.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE. THE SLEDB-110V-MS MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

IMPORTANT

READ CAREFULLY BEFORE OPERATING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. IF UNSURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL

PROFESSIONAL.

WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT. DO NOT OPERATE IN CLOSE

PROXIMITY OF COMBUSTIBLE OR FLAMMABLE MATERIALS. NEVER LOOK DIRECTLY AT LIGHT WHEN ON.

WARNING: CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL/ELECTRICIAN TO INSTALL THIS DEVICE IN

ACCORDANCE WITH APPROPRIATE LOCAL AND NEC CODES AND REGULATIONS.

WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES

AND REGULATIONS.

WARNING: DEVICE IS SUITABLE FOR INSTALLATION IN WET LOCATIONS; GFCI PROTECTION

RECOMMENDED.

WARNING: ALTHOUGH FIXTURE IS WATERPROOF, IT IS NOT DESIGNED OR INTENDED TO BE SUBMERGED.

WARNING: DO NOT ALLOW LINE VOLTAGE WIRES TO BECOME SUBMERGED!

•ALL OUTDOOR INSTALLATIONS AND INDOOR INSTALLATIONS NEAR A WET LOCATION REQUIRE THE

USE OF A GFCI DEVICE FOR SAFETY, ACCORDING TO THE NATIONAL ELECTRICAL CODE® (NEC).

•KEEP AWAY FROM FLAMMABLE OBJECTS. DO NOT POSITION WITHIN ONE (1) INCH OF ANY

COMBUSTIBLE MATERIALS.

•IF DROPPED OR DAMAGED, THE UNIT MAY NO LONGER BE WATERPROOF AND SHOULD BE

REPLACED.

•TO AVOID HAZARDS TO CHILDREN, ACCOUNT FOR ALL PARTS AND DESTROY PACKING MATERIALS.

SLEDB-110V-MS

Larson Electronics, LLC

Phone: (877)348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

2 of 5

MOUNTING

Mount to any flat surface capable of holding the weight utilizing the predrilled

mounting holes. Mount in any direction as long as the motion sensor can still detect

motion.

WIRING

We strongly encourage a licensed electrician install this product, especially in outdoor locations

where weatherproofing may be required. Voltage driver permitsoperation at 110-120V AC.

Warning: Check product label for correct inputvoltage!

Attach supply line wires to the appropriate light fixture

wires as shown in the diagram

Take precautionary steps for weatherproofing all

connections if installed in a location where water may

come in contact with the unit. Ensure the unit is properly

grounded.

The Larson Electronics SLEDB-110V-MS Class II Beacon works on 110-120V AC, offers a choice of several colors

and is equipped with an aluminum base. The SLEDB-110V-MS comes equipped with a motion sensor that turns the

light on when movement is detected. The motion sensor has a user adjustable time delay.

INSTALLATION

This unit comes pre-assembled with the selected color from factory.Follow the steps below for installing and

maintaining the strobe light.

SLEDB-110V-MS

Larson Electronics, LLC Phone: (877)348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 3 of 5

MOTION SENSOR

Operating voltage

Rated load

HF system 5.8GHz±75MHz, ISM wave band

Transmitting power <0.5mW

Power consumption ≤0.5W(standby)

Detection zone Max.(D x H): 16m x 15m

Detection sensitivity /// 50%10%%%%%%

Hold time 5s / 45s / 5min / 15min

Daylight sensor 2Lux/10Lux/30Lux/Disable

Mounting height 15m Max.

Motion detection 0.5~3m/s

Detection angle 150°(wall installation)

360°(ceiling installation)

Operating temperature -25℃~60℃

IP rating IP20

Setting

ON ON

III

1 2

10%

50%

75%

100%

III

3 4

45s

5min

15min

10lux

2lux

30lux

III

By selecting the combination on the DIP switch, sensor data can be precisely set for each specific application.

DDetection Area

Detection area can be reduced by selecting the combination on the

DIP switches to fit precisely each application.

HHold Time

Refers to the time period the lamp remains at 100% illumination after

no motion detected.

DDaylight Sensor

The sensor can be set to only allow the lamp to illuminate below a

defined ambient brightness threshold.

When set to Disable mode, the daylight sensor will switch on the lamp

when motion is detected regardless of ambient light level.

30lux:twilight operation, 2lux, 10lux: darkness operation only.

Disable

OONN

5 6

SLEDB-110V-MS

Larson Electronics, LLC

Phone: (877) 348-9680

Fax: (903) 498-3364 www.larsonelectronics.com

4 of 5

MOTION SENSOR

The SLEDB-110V-MS operates like a standard on/off light switch. The

circuit is normally open when no motion is present. Once motion is

detected, the internal switch changes to a closed circuit, allowing

voltage to pass through the sensor and power the device(s) at the other

end.

The sensor is an active motion detector; it emits high-frequency

electro-magnetic waves (5.8GHz) and receives their echo. The sensor

detects the change in echo from even the slightest movement in its

detection zone. A microprocessor then triggers the “switch light ON”

command. Detection is possible through doors, panes of glass or thin

walls.

IMPORTANT: persons or objects moving towards the sensor are

detected best. NOTE: the high frequency of the output of this sensor is

<10Mw – that is just one 100th of the transmission power of a mobile

phone or the output of a microwave oven.

Malfunction Cause Remedy

The load will not work - wrong light control setting selected

- load faulty

- mains switch OFF

- adjust setting

- change load

- switch ON

The load is always working - continuous movement in the

detection zone

- check zone setting

Load works without and identifiable

movement

- sensor is not mounted for detecting

movement reliably

- movement occurred, but not

identified by the sensor (movement

behind a wall, movement of small

object in immediate vicinity etc.)

- securely mount enclosure

- check zone setting

The load will not work despite

movement

-rapid movements are being

suppressed to minimize

malfunctioning or the detection zone

you have set is too small

-check zone setting

SLEDB-110V-MS

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 5 of 5

MOTION SENSOR LOCATION

This unit uses a microwave sensor, which is more reliable than the standard PIR sensor. This sensor is

enclosed in a waterproof box below the light. The sensor DOES NOT need line of sight. The microwave sensor

is capable of sensing through the waterproof enclosure and detecting motion, which in turn activates the light.

Not seeing an external sensor may make you think that your unit is missing the motion sensor. It is not. The

sensor is included and will function as intended.

MAINTENANCE

If the lens becomes dirty, wipe down with a mild soap and water solution.

It isrecommended to occasionally inspect the unit for any defects and toensure the cable isnotfrayed and is gripping tightly in all

points ofcable contact.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The SLEDB-110V-MS is designed to provide years of reliable performance. Should the need for replacement parts arise,

please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SA[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Indice

Altri manuali Larson Electronics Attrezzatura di illuminazione

Larson Electronics

Larson Electronics EPL-EMG-LED-100W-RT Manuale utente

Larson Electronics

Larson Electronics HAL-RSL Series Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Manuale utente

Larson Electronics

Larson Electronics EPL-FL1524-25-1523 Manuale utente

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Manuale di istruzioni

Larson Electronics

Larson Electronics SPLED-QP-1X10WRE Manuale utente

Larson Electronics

Larson Electronics EPL-SBDL-150RT-72 Manuale utente

Larson Electronics

Larson Electronics EPLC2-PT-2X150LED-RT Manuale utente

Larson Electronics

Larson Electronics HALD-48-1X4-2X50LED-DIMM Manuale utente

Larson Electronics

Larson Electronics LEDP5W-30-TP1-50CR Manuale utente

Larson Electronics

Larson Electronics FRL-EMX-18-90W-FUVC-KT Manuale utente

Larson Electronics

Larson Electronics VPLHL-7WLED-PC-GR30 Manuale utente

Larson Electronics

Larson Electronics WAL-TJL-250W-LED-CPR Manuale utente

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-JB2-6-EPP Manuale utente

Larson Electronics

Larson Electronics LEDWP-600E-M-E2E-20C Manuale utente

Larson Electronics

Larson Electronics ORS-120-8M-4X150W-LED Manuale utente

Larson Electronics

Larson Electronics EPL-LED-150W-RT-140DB-480V Manuale utente

Larson Electronics

Larson Electronics VPLHL-15WLED-PC-GR30 Manuale utente

Larson Electronics

Larson Electronics HALD-48-1X4-2X50LED Manuale utente

Larson Electronics

Larson Electronics HAL-16C-185LED-CPR-100 Manuale utente

Larson Electronics

Larson Electronics WDL-12-70W-LED-SFC-WCM Manuale utente

Larson Electronics

Larson Electronics EPL-SL-4-50X-50LED-RT-MBC-EPP Manuale utente

Larson Electronics

Larson Electronics GAU-EMG-2X5W-LED-WP Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente