Larson Electronics HAL-16C-185LED-CPR-100 Manuale utente

HAL-16C-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

The Larson Electronics HAL-16C-185LED-CPR-100 hazardous location LED light cart provide operators

with a powerful and energy efficient alternative to other hazardous area luminaries such as high pressure

sodium (HPS), metal halide (MH), and halogen lights. LED technology and a sturdy design make this light

perfect for a wide variety of illumination needs. The durable wheelbarrow cart design can be adjusted for

angle and provides a sturdy and rugged stand for portable illumination, temporary hazardous area lighting,

and other hazardous location lighting needs.

WARNING

To avoidthe riskof fire,explosion or electric shock, thisproduct should be installed, inspectedand

maintained by a qualified electricianonly, in accordance with all applicableelectrical codes.

To avoidelectric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

•Make sure the supply voltage is within the luminaires’ voltage rating.

•Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

The light fixture on this wheelbarrow cart is factory sealed.

CART OPERATION

The wheelbarrow cart assembly consists of 2 parts:

1. Light head

2. Wheelbarrow cart base

To assemble cart, insert light head over center hole of wheelbarrow cart and tighten hand screw. The

wheelbarrow cart is now ready for use.

Tilt cart using both handles and maneuver like a wheelbarrow. Simply roll entire assembly to a new location

once assembled. Make sure light head is secure prior to maneuvering cart.

WARNING: Be sure all hand screws are tight before transporting! Use caution when maneuvering near

inclines or drop offs.

Run power cord to a nearby receptacle outputting voltage listed on product label.

WARNING: check nameplate for proper voltage. Damage from improper voltage may void warranty.

To adjust light head vertically, loosen hand screws on either side. Once desired angle is achieved, tighten

both hand screws to secure light in its place. Loosen the single hand screw holding light head to rotate

horizontally. Be sure all hand screws are tight before transporting!

185 Watt Hazardous Location LED Light - Wheelbarrow Cart - C1D2 -

ATEX - 100 foot Cord w/ EXP Plug

Instruction Manual

HAL-16C-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

WIRING(see attached wiring diagram)

This unitcomes preconfigured with selected cord cap. The is outfitted with 100` of 16/3 chemical and abrasion

resistant SOOW cord that is fitted with an explosion proof cord cap for easy connection to explosion proof

outlets. Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20

20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for

use with 220-240V explosion proof outlets. **PLEASE NOTE** voltage ratings on plugs and outlets are

MAXIMUM voltage. For low voltage applications, proper voltage must be applied to the outlet or damage to the

light fixture will occur.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

WARRANTY

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 or sales@larsonelectronics.com for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE MAY

VOID WARRANTY.

Indice

Altri manuali Larson Electronics Attrezzatura di illuminazione

Larson Electronics

Larson Electronics GL-2051-M Manuale utente

Larson Electronics

Larson Electronics HALD-48-1X100LED Manuale utente

Larson Electronics

Larson Electronics TPM-2XWP60E-25C Manuale utente

Larson Electronics

Larson Electronics WCDE-11-6HPS-MR Manuale utente

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Manuale utente

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manuale utente

Larson Electronics

Larson Electronics PTB-1-50FT Manuale utente

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Manuale utente

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-JB2-6-EPP Manuale utente

Larson Electronics

Larson Electronics C1D2 Manuale utente

Larson Electronics

Larson Electronics IND-HVAC-ACS-R1-DP-24-2L-XB Manuale utente

Larson Electronics

Larson Electronics FRL-EMX-18-90W-FUVC-KT Manuale utente

Larson Electronics

Larson Electronics EPLC2-HB-50LED-RT Manuale utente

Larson Electronics

Larson Electronics WDL-12-70W-LED-SFC-WCM Manuale utente

Larson Electronics

Larson Electronics VPLHL-7WLED-PC-GR30 Manuale utente

Larson Electronics

Larson Electronics LEDB-4-IR Manuale utente

Larson Electronics

Larson Electronics WAL-TL-3XTL-C-SOL-100C Manuale utente

Larson Electronics

Larson Electronics SOL240-2XWP50E2X200A-RMBB-DNS-7.63SQ Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Manuale utente

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-EB Manuale utente

Larson Electronics

Larson Electronics HID-35-RC-W Manuale utente

Larson Electronics

Larson Electronics EPL-50W-120x12-50 Manuale utente

Larson Electronics

Larson Electronics VPLHL-7WLED-GR30 Manuale utente

Larson Electronics

Larson Electronics LM Multi Stage Series Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente