Larson Electronics PML-15 Manuale utente
PML-15
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
1of 2
HID ControLight Permanent Mount Light
3200 Lumens, 35 Watt - 15 million candlepower - PML-15
Instruction Manual
Deuts
Thank you for your purchase of the Larson Electronics PML-15.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE PML-15 MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL
APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
Low Voltage DC
Connect power to power supply outputting low voltage at 12 Volts DC. This variable voltage allows greater versatility
without affecting light output. Ensure deutsch connectors are properly connected (If applicable)
DETACHABLE CORDS
•Cord is attached via a weatherproof 2-pin Deutsch connector.
•The cord is detachable by depressing the tab on the top of the connectors. This enables the
operator to remove and store the light while leaving the cord connected to the power source.
•Additional or replacement cords can be ordered from our website. Contact us or visit LarsonElectronics.com for more
information.
PML-15
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
2of 2
OPERATION
1. Use the handle on the backof the light totilt up/down and pan left/right.
2. Adjust the tightness of pivot/pan movement using the tightening bolts on the side of the base hinge.
3. Connect the Deutsch connector from power cord to light.
4. Connect power source and flip the switch on back of light to turn on.
NOTE: Check forproper voltage before first use!
5. Power transformers (DCP-11-DP)can be purchased through our website to run this spotlight from household wall
outlets.
The sealed beam in this unit pulls 13 amps continuously, so 15 amp fuse is required. A 15 amp fuse is typical
on most cigarette lighter sockets, however, it is not recommended that you attempt to run 2 of these lights on a
socket splitter without increasing the fuse capacity. This spotlight produces 1050 LUX at 25 feet, and projects a beam
700 feet. At its widest point, the beam is nearly 70 feet wide. The light is designed to project light at distance and the
beam pattern resembles a long cigar with its thickest point past the midway point.
MOUNTING
The light features a permanent mount base, measuring 4 inches square that is secured with 4 corner bolts. Mount
light securely; making sure bracket is square with surface.
ADJUST LIGHT
Light beam can be adjusted vertically/horizontally by the handle. The spotlight, will hold its position once the beam is
placed. Adjust the tightening bolt to increase or lessen the "position holding" tension based on the amount of vibration in
the environment. Should light adjustment become loose, tighten bolts on the base.
To change the lamp,remove the screws on the lens cover. Take the face ring off of the lamp
and pull the bulb out of the socket freeing it form the spring fasteners. Place the new bulb in its
socket and replace face ring.
Lens Screw
MAINTENANCE
Iis good practice to routinely clean and check the fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The PML-15 is designed to provide years of reliable performance. Should the need for replacement parts arise, please
contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Indice
Altri manuali Larson Electronics Attrezzatura di illuminazione
Larson Electronics
Larson Electronics PTB-1-50FT Manuale utente
Larson Electronics
Larson Electronics EPL-16C-150LED-RT Manuale utente
Larson Electronics
Larson Electronics EPEXC-1C-10.3-GFI-50C-BCE Manuale utente
Larson Electronics
Larson Electronics EXP-EMG-EXT-LE6-3L Manuale utente
Larson Electronics
Larson Electronics EPL-LED-50W-RT-JB2 Manuale utente
Larson Electronics
Larson Electronics FRL-4P-S1-60-1X-T5HO-130W-UVC Manuale utente
Larson Electronics
Larson Electronics EPL-FL1524-LED Series Manuale utente
Larson Electronics
Larson Electronics SPLED-QP-1X10WRE Manuale utente
Larson Electronics
Larson Electronics EPL-HB-150LED-RT-140DB-JB3 Manuale utente
Larson Electronics
Larson Electronics EPL-HB-150LED-RT-100-EPP Manuale utente
Larson Electronics
Larson Electronics EPL-LQP-2X150RT Manuale utente
Larson Electronics
Larson Electronics EPL-48-4L-LED-D-V2-100C Manuale utente
Larson Electronics
Larson Electronics XLE-UVC-XX-SGKT-2X Manuale utente
Larson Electronics
Larson Electronics HALD-EMG-24-1X150LED-V3 Manuale utente
Larson Electronics
Larson Electronics GVP-48-2L-LED-48VDC-R2 Manuale utente
Larson Electronics
Larson Electronics LEDB-4-IR Manuale utente
Larson Electronics
Larson Electronics EPL-QP-2X50LED-RT-100 Manuale utente
Larson Electronics
Larson Electronics GAU-HB-100LED-RT-UVA-10C Manuale utente
Larson Electronics
Larson Electronics EPL-FL1524-100 Manuale utente
Larson Electronics
Larson Electronics EPL-HB-150LED-RT-NSF Manuale utente
