Larson Electronics EPS-PB10-2XC-M2-YR Manuale utente

EPS-PB10-2XC-M2-YR

Larson Electronics, LLC Phone: Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Explosion Proof Mushroom Push Button Switch

(2) Contact Blocks - Class I and II, Divisions 1 and 2 - Yellow Visibility Plate

Instruction Manual

Thank you for your purchase of the Larson Electronics EPS-PB10-2XC-M2-YR.

WARNING

TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK,THIS PRODUCT SHOULD BE INSTALLED,

INSPECTED AND MAINTAINED BY AQUALIFIED ELECTRICIAN ONLY,IN ACCORDANCE WITH ALL

APPLICABLE ELECTRICAL CODES.

TO AVOID ELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

(877) 348-9680

The EPS-PB10-2XC-M2-YR from Larson Electronics is an Explosion Proof Single Push Button Switch with Visibility Plate

that is designed for use in hazardous work areas, such as chemical plants, oil refineries, and settings where combustible

gases or dust may be present. This 10-amp device features the following explosion proof ratings: Class I Division 1 and 2;

and Class II Division 1 and 2. In industrial and commercial settings, the front-operated push button switch may be used to

support basic features of machines lacking electrical circuits for control. When ordering this unit, buyers may choose from

1/2" and 3/4", dead end and feed thru options. The EPS-PB10-2XC-M2-YR is equipped with a visibility plate.

CAUTION:

A nameplate is furnished on the cover reading "DISCONNECT THIS ENCLOSURE FROM

SUPPLYING CIRCUIT BEFORE OPENING". Be sure the flame paths (cover to box mating

surfaces and threaded openings) do not become damaged or out of tolerance (refer to back of

sheet for tolerances). Do not install in a corrosive area which will attack the" copper free"

aluminum alloy or stainless steel parts unless the castings and parts have been protected

against the specific corrosive environment.

DESCRIPTION:

The EPS-PB10-2XC series maintained contact, mushroom head, push/pull operator assemblies

are for use in hazardous location Class I, Groups B, C & D; Class II, Groups E, F & G;

Class III areas when used with deep style boxes. These units are heavy-duty, 600 V AC rated.

OPERATION:

The mechanical action of these devices is maintained push/pull operation. The electrical action is dependent upon the

contact block used.

EPS-PB10-2XC-M2-YR

Larson Electronics, LLC Phone: Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MAINTENANCE:

For detail ofparts, refer to graphic below.To prevent binding,

the knob and collar area should be cleaned periodically.

INSTALLATION

We recommend only a licensed electrician install this product. All applicable local and

national electrical and building code should be followed when installing.

EPS-PB10-2XC-M2-YR devices are for surface mounting in hazardous atmospheres, as defined in

the NEC Article 500. They contain an electrical device, and must have conduit sealing fittings (per

NEC article 50 1-5)on all conduit openings. Use Larson Electronics "EYM" series (or equivalent).

Mount the box using the cast mounting lugs provided. Install sealing fittings as required in Class I &

IT areas.

Thread conduit on to seals (NOTE: FOR CLASS I AREAS, CONDUIT MUST ENGAGE A

MINIMUM OF 5 FULL THREADS). The conduit threads should be lubricated with a non-electrical

insulating lubricant, or pipe joint compound which will not promote corrosion or chemically attack

aluminum.

After conduit system has been properly installed, pull the supply wires and make wiring

connections as required. The electrical circuits and ground continuity should be checked with an

instrument approved for the area.

A FLAME PATH IS MACHINED ON BOX & COVER SUCH THAT A 0.0015" FEELER GAUGE WILL

NOT ENTER THE JOINT MORE THAN 1/8" WHEN FULLY ASSEMBLED AND BOLTED. CARE

MUST BE TAKEN THAT MACHINED SURFACES AND THREADED AREAS ARE NOT

DAMAGED.

REMEMBER TO SAVE ONE OF THESE SHEETS FOR MAINTENANCE PERSONNEL.

(877) 348-9680

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Storeit in a secure place out of the reach of children

when not in use.Inspect for good working condition prior tostorage and before re-use.

REPLACEMENT PARTS

The EPS-PB10-2XC-M2-YR is designed to provide years of reliable performance. Should the need for replacement parts

arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Indice

Altri manuali Larson Electronics Interruttore

Larson Electronics

Larson Electronics EPSW-1PH-20 Manuale utente

Larson Electronics

Larson Electronics EPS-25A Manuale utente

Larson Electronics

Larson Electronics EPO-20A Manuale utente

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Manuale utente

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT Manuale utente

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Manuale utente

Larson Electronics

Larson Electronics EPSW-30A-WP Manuale utente

Larson Electronics

Larson Electronics EPL-SW Series Manuale utente

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Manuale utente

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP Manuale utente

Larson Electronics

Larson Electronics EPS-10HP-3PST Manuale utente

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-N4X-V3 Manuale utente

Larson Electronics

Larson Electronics EPS-PB20 Manuale utente

Larson Electronics

Larson Electronics EPS-2XPB-SG-DPMS Manuale utente

Larson Electronics

Larson Electronics EPCS-PB10-1XMPB-3PSW Manuale utente

Larson Electronics

Larson Electronics EPS-FS-B-2PSW Manuale utente

Larson Electronics

Larson Electronics EXP-RT-3PH-MIN.5-208V Manuale utente

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC Manuale utente

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series Manuale utente

Larson Electronics

Larson Electronics EPS-SW1-ESTP Manuale utente

Larson Electronics

Larson Electronics C1D2 Manuale utente

Larson Electronics

Larson Electronics EXP-EL-CSS-250A-R1-NO Manuale utente

Larson Electronics

Larson Electronics EPS-25A-3W Manuale utente

Larson Electronics

Larson Electronics EPS-3PSW-MMS Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente