LaserLiner Quadrum Manuale utente

Quadrum / Quadrum Green

Laser

530-670 nm

auto auto man

IP 66

This is a precision instrument which must be handled with care. Avoid

impacts and jarring. Store and transport the instrument in its case!

Turn off the unit when it is not in use! Clean with a soft cloth and

glass cleaner.

Laser radiation!

Avoid direct exposure

to the eyes.

Laser class 3R

< 5 mW Ċ530 - 670 nm

EN60825-1:2007-10

Caution: Prior to using the laser, you must read the safety instructions for

laser class 3R thoroughly. Warning signs must not be removed from the laser

measuring device! Do not look directly into the beam. Lasers must be kept

out of reach of children. Never intentionally aim the device at people. This is a

quality laser measuring device and is 100% factory adjusted within the stated

tolerance. For reasons of product liability, we must also draw your attention

to the following: Regularly check the calibration before use, after transport

and after extended periods of storage. We also wish to point out that absolu-

te calibration is only possible in a specialist workshop. Calibration by yourself

is only approximate and the accuracy of the calibration will depend on the

care with which you proceed.

General safety instructions

Fully automatic rotary laser with red or green laser

technology.

– With additional red plumb laser

– Laser modes: spot, scan, rotary and hand receiver mode

– All functions can be controlled remotely.

– optional SensoLite 310: Laser receiver range up to 300 m radius

– optional SensoMaster 400 (Quadrum red only): Laser receiver range in

excess of 300 m radius. With longer laser receiver unit and millimetre exact

distance reading for laser level.

– 5° self-levelling range, precision 1 mm / 10 m

Quadrum / Quadrum Green

External influ-

ence

Adjustment phase

Sensor Automatic

ADS activation:

press the tilt

button; the tilt

LED flashes every

second.

The

laser

remains stationary as

a precaution, the laser

flashes and the tilt

LED is lit continuously.

ADS active after

30 seconds, rapid

flashing of the

tilt LED.

Rotation

begins

ADS function

The ADS does not activate the monitoring function until 30 seconds

after the laser levelling procedure has been completed (set-up phase).

The tilt LED flashes every second during the set-up phase, rapid

flashing, when ADS is active.

Special product features and functions

The rotary laser aligns itself automatically. It is set to the

required initial position (to within an operating angle of ± 5°) and the

automatic system then performs the necessary fine adjustment, with three

electronic measurement sensors detecting the X, Y and Z axes.

The anti-drift system (ADS) prevents erroneous or inaccurate

measurements. How it works: continuous monitoring of the alignment of the

laser is activated 30 seconds after the ADS is switched on. If the device

moves due to the influence of external factors or the laser loses its height

reference, the laser will come to a standstill. Additionally, the laser flashes

and the tilt LED is lit continuously. To continue working, press the tilt button

again or switch the device off then on again. Erroneous and inaccurate

measurements are thus prevented simply and reliably.

The ADS is not active following switch-on. Once the device has been set

up, press the tilt button to activate the ADS, enabling you to protect the laser

from changes in position caused by the device being disturbed by external

factors. The tilt LED flashes to indicate that the ADS function is active; see

the diagram below.

Quadrum Green: green laser technology

The distance at which a laser is visible to the naked eye depends on its colour

i.e. wavelength. This is because of the human eye's physiology – green

appears brighter to us than red. Depending on ambient light, green lasers

are therefore many times more visible than red lasers; in indoor areas this is

as much as 12 times brighter. This permits applications on dark surfaces, over

longer distances and work in very bright ambient light. A red laser with a 635

nm wavelength is used as a reference value for brightness differentiation.

In contrast to red lasers, green laser light can only be produced indirectly. This

is a source of potential characteristic fluctuations:

– The optimal operating temperature is 20°C. Outside its operating tempera-

ture range of 0 – 40°C Quadrum Green is darker. IMPORTANT: Allow the

unit enough time to adapt to the ambient temperature before switching the

unit on.

– Laser brightness may vary somewhat from one unit to another. This is a

natural phenomena and excluded from warranty claims.

– Green Laser will only work with certain Receivers. The maximum range of

the Receiver is shorter, please refer to technical details.

Horizontal

levelling

Vertical level-

ling

Slope function 90° angle Plumb

function

auto auto man

Space grids: These show the laser planes and functions.

auto: Automatic alignment / man: Manual alignment

Transport LOCK: The device is protected by a special motor

brake during transport.

IP 66

The device characterised by specific protection against

dustand rain.

Quadrum / Quadrum Green

–

AAA

–

AAA

–

Do not expose batteries to excessive heat such as sunshine, fire, etc.

Only rechargeable batteries must be charged. Used batteries must not

be disposed of as household waste. Please take them to a collection

point for used batteries or for special waste. Ask your local authority

for further details. Batteries with the recycling symbol can also be retur-

ned to our dealerships or to our Technical Service.

Battery charging

– Charge the device's battery completely prior to use.

– Connect the charger to mains power supply and the charging socket (I) of

the battery compartment (K). Please only use the charger supplied; using a

different charger will invalidate the warranty. The rechargeable battery can

also be charged when it is not inserted in the device.

– When the rechargeable battery is being charged, the LED on the charger

(M) lights up red. When the LED changes to green, charging is complete.

When the unit is not connected to the charger the power charger's LED

lamp will blink.

– Alkaline batteries (4 x type C) can be used as an

alternative. Insert them in the battery compart-

ment (J) as per the installation symbols.

– Insert battery (K) / battery compartment (J) into

slot (F) and secure it in place with fastening

screw (H). The electrical contacts (G) must be

connected.

– With the rechargeable battery inserted, the

device is ready to run even during charging.

– When all 3 LEDs (2, 4, 5) light up briefly and

the device switches off, the batteries must be

replaced or the rechargeable battery charged.

Insert batteries into the remote control

– Observing the correct polarity.

Vertical operation

Reference / plumb laser outlet

Prism head / laser beam outlet

Receiver diodes for remote con-

trol (4 x)

Control panel

5/8" thread /

Reference, plumb laser outlet

Slot for rechargeable battery /

battery compartment

Electrical contacts

Battery compartment / battery

fastening nut

Charging socket

Battery compartment

Rechargeable battery

compartment

Mains unit / charger

Operation indicator

red: battery is charging

green: charging process complete

Quadrum / Quadrum Green

34 56

Remote controlControl panel Quadrum

auto/man function

auto/man function LED

LED off: automatic alignment

LED on: manual alignment

ON/OFF button

Operation indicator

Tilt function LED

Tilt function

Rotary speed for selection, 600 /

300 / 120 / 60 / 0 rpm

Positioning button (rotate to the

right)

Positioning button (rotate to the

left)

auto/man. function: Y axis pro-

ceed as above

auto/man. function: Y axis pro-

ceed as below

auto/man. function: X axis pro-

ceed as above

auto/man. function: X axis pro-

ceed as below

Scan mode

Operation indicator

Infrared signal emitter

auto

± 5°

auto auto

If the auto/man. LED flashes, the maximum adjustment range of 5° has

been reached. Set up the device horizontally, turn it off and then on

again.

Positioning the vertical laser level

In vertical mode the laser level can be positioned exactly. "Sensor Automatic"

remains active and levels to the vertical laser level. Refer to the illustration

below.

auto/man function LED OFF: Automatic alignment

If the device has been placed on a surface with too much of a slope

(more than 5°), there is a warning sound, the prism head remains stati-

onary and the laser starts to flash. The device must then be placed on a

more even surface.

– The device levels itself automatically to within a range of ± 5°. During the

set-up phase, the laser flashes and the prism head remains stationary. When

levelling is complete, the laser lights up continuously and rotates at maxi-

mum speed. Refer also to the sections about "Sensor Automatic" and "ADS

Tilt".

Horizontal levelling and vertical levelling

– Horizontal: Position the device on a level surface or

on a tripod.

– Vertical: Set the unit on its side feet. The operator

panel should be at the top. With the optional wall

bracket (product ref. 080.70), the device can be

mounted on a tripod for vertical usage.

– Press the "ON/OFF" switch

Quadrum / Quadrum Green

± 5°

man

auto/man function LED ON: Manual alignment

Slope function > 5°

Steeper slopes can be set using the angle plate,

which is available as an optional extra (product

ref. 080.75). TIP: Allow the device to align itself

automatically and set the angle plate to the zero

position. Then press the auto/man button to switch

the automatic sensor off. Finally, incline the device

to the angle you require.

When the 5° maximum slope range has been reached, the laser will

stay fixed and blink. In this case, reduce the slope angle.

Slope function up to 5° – vertical

Slope function up to 5° – horizontal

This function deactivates the automatic sensor. To use the function, press the

auto/man button. The plus/minus buttons are used to re-adjust the slope by

means of a motor. In the process the X-and Y-axis can be adjust separately.

Refer to the illustrations below.

Working with the reference/plumb laser

The unit has two reference lasers. In horizontal

operation these lasers can be used to drop a per-

pendicular. In vertical operation these reference

lasers are used to align the unit. This is done by

adjusting the reference lasers parallel to the wall.

This aligns the vertical laser plane at a right angle

to the wall, see illustration.

Hand receiver mode

Working with the laser receiver (available as an

optional extra): Set the rotary laser to maximum

speed and switch on the laser receiver. Refer to

the operating instructions for the respective laser

receiver about this.

Scan mode

The scan button can be used to activate and set

a lightintensive segment in 4 different widths.

You position the segment via the direction but-

tons.

Spot mode

You access spot mode by pressing the rotary

button repeatedly until the laser stops rotating.

The laser can then be positioned exactly at the

measuring point by means of the direction but-

tons.

Laser modes

Rotary mode

The following speeds can be set using the rotary

button: 0, 60, 120, 300, 600 rpm

Altri manuali per Quadrum

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LaserLiner Livello laser

LaserLiner

LaserLiner MasterLevel Box Manuale utente

LaserLiner

LaserLiner DigiLevel Plus 40 Manuale utente

LaserLiner

LaserLiner HandyLaser Magnum Manuale utente

LaserLiner

LaserLiner SuperPlane-Laser 3D Manuale utente

LaserLiner

LaserLiner Greenline-Laser 3P Manuale utente

LaserLiner

LaserLiner HandyLaser Manuale utente

LaserLiner

LaserLiner Revolution Manuale utente

LaserLiner

LaserLiner SuperSquare-Laser 2G Manuale utente

LaserLiner

LaserLiner AL 22 Classic Manuale utente

LaserLiner

LaserLiner Greenline-Laser 1 Pro Manuale utente

LaserLiner

LaserLiner PowerCross-Laser 8 S Manuale utente

LaserLiner

LaserLiner AL 26 Plus Manuale utente

LaserLiner

LaserLiner DigiLevel Plus 40 Manuale utente

LaserLiner

LaserLiner AutoCross-Laser ACL 2C RX Manuale utente

LaserLiner

LaserLiner ActiveFinder XP Manuale utente

LaserLiner

LaserLiner CombiCross-Laser 5 DLD Manuale utente

LaserLiner

LaserLiner AutoCross-Laser ACL 3C Manuale utente

LaserLiner

LaserLiner DigiLevel Pro 40 Manuale utente

LaserLiner

LaserLiner CompactCube-Laser 3 Manuale utente

LaserLiner

LaserLiner DigiLevel Pro 120 Manuale utente

LaserLiner

LaserLiner PowerPlane-Laser 3G Manuale utente

LaserLiner

LaserLiner MultiBeam-Laser 5 Manuale utente

LaserLiner

LaserLiner SuperCross-Laser 2GP Manuale utente

LaserLiner

LaserLiner SmartCross-Laser Manuale utente

Manuali Livello laser popolari di altre marche

Nedo

Nedo ET-5 Manuale utente

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manuale utente

Spectra

Spectra LL300N Manuale utente

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manuale utente

Nedo

Nedo Crossliner 4 Manuale utente

Lasertec

Lasertec FX360G Manuale utente

Flex

Flex ALC 8 Manuale utente

Black & Decker

Black & Decker LZR5 Manuale utente

Johnson

Johnson 40-6692 Manuale utente

Cocraft

Cocraft HL 20-SG Manuale utente

Zircon

Zircon iLine Manuale utente

HWH

HWH 310 SERIES Manuale utente

Leica

Leica iCON robot 60 Manuale utente

DeWalt

DeWalt DW082 Manuale utente

imex

imex EL20 Manuale utente

Fixturlaser

Fixturlaser NXA D I-0912 Manuale utente

Wacker Neuson

Wacker Neuson PAL450 Manuale utente

Metrica

Metrica 33806 Manuale utente