Lathem CT SERIES Manuale utente
THIS EQUIPMENT COMPLIES WITH FCC REQUIREMENTS
PURSUANT OF PART-15
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: Changes or modifications to this product not expressly approved by
the party responsible for compliance could void the user’s authority to operate this
equipment.
Lathem Time Corporation
200 Selig Drive, SW,
Atlanta, GA 30336
www.lathem.com
Copyright © 2016 Lathem Time Corporation. All rights
reserved. Revised 04-18-2017
Document number: USG0103C
Contents iii
Contents
Package Contents 1
Install the CT Series Clock 2
Wi-Fi or Wired Network Connection........................................... 4
PayClock Online 6
Adding a CT series clock.............................................................. 6
Step 1 - Adding a CT series Clock............................................. 6
Step 2 - Connect the Clock to PayClock Online......................... 6
Using the CT Clock 8
Employee Transactions ................................................................ 8
Clocking IN/Out - Finger Sensor (CT72).................................... 8
Clocking IN/Out - Badge............................................................. 8
Clocking IN/Out - PIN................................................................. 9
Department Transfers - Finger Sensor (CT72).......................... 9
Department Transfers - Badge................................................... 9
Department Transfers - PIN....................................................... 9
Amount Entries - Finger Sensor (CT72)................................... 10
Amount Entries - Badge........................................................... 10
Amount Entries - PIN................................................................ 11
Viewing Totals - Finger Sensor (CT72).................................... 11
Viewing Totals - Badge ............................................................ 11
Viewing Totals - PIN................................................................. 11
Supervisor Transactions 12
Viewing Punches...................................................................... 12
Adding Punches....................................................................... 13
Viewing Totals.......................................................................... 13
Send Message ......................................................................... 13
Override Lockout...................................................................... 14
Enrolling Fingers 15
Enrolling Employee Fingers ..................................................... 15
iv Contents
Administrator Functions 17
Network .................................................................................... 17
Wireless.................................................................................... 18
Sync Now ................................................................................. 18
Date/Time Setup ...................................................................... 19
Signal-Door Access.................................................................. 19
Device Info................................................................................ 20
Error Log................................................................................... 20
Check for Updates.................................................................... 20
Factory Reset...................................................................... 20
Troubleshooting the CT Series 22
General Troubleshooting ............................................................ 22
CT Series Troubleshooting......................................................... 22
Appendix A – Installing a Battery 25
Appendix B – Adjusting Finger Sensitivity 26
Appendix C – Bell Relay Connections 27
Appendix D – Access Relay Connections 32
Appendix E – Add/Edit/Delete Bell Events 34
Package Contents 1
Package Contents
Please verify that your package includes the following items. If your
package is missing an item, please call our help desk at (800) 224-1877.
Note: Remove the protective film on the clock bezel and touch screen by
pulling the white tabs in the upper right corner after the clock is installed.
Recommended Installation Tools
Online and Email Support
Lathem.com provides access to numerous support resources. Visit the
following link: http://kb.lathem.com for additional help or to submit a
question. You should receive a reply within 24 hours.
Telephone Support
The help desk is available between the hours of 8am and 6pm ET
Monday through Friday. Please call (800) 224-1877 to speak with our
help desk.
2 Install the CT Series Clock
Install the CT Series
Clock
Step 1: Select a site to install your clock that will be convenient to
employees clocking in and out. When deciding where the clock will be
installed, keep in mind that an 115vAC power outlet should be within
reach of the mounting location as well as either a wired or wireless
internet connection.
Step 2: After selecting the appropriate installation site, use the mounting-
plate to determine the appropriate height. Hold the mounting-plate on the
wall and mark the screw hole locations on the wall.
Install the mounting-plate to the wall using the supplied screws. For
sheetrock walls, drill a 3/16” diameter hole through each of the four
screw locations; each approx. 1-1/2” deep. Install the plastic “anchors”
included in the mounting screw packet.
Note: The bottom of the clock should be about 45 inches from the floor.
Install the CT Series Clock
•
3
If using a wired network connection plug the RJ 45 network cable into the
Ethernet port and the Power Adapter plug into the power adapter port
which is located in the compartment on the back of the clock.
Step 3: Align the CT clock with the tabs on the mounting-plate and
secure the two together with the 2 Philips head screws. Be careful not to
pinch the AC cord or network cable.
When finished, plug the power adapter into an AC wall outlet.
4 Install the CT Series Clock
Wi-Fi or Wired Network Connection
The CT series clock can communicate with PayClock Online via a Wi-Fi
or Wired Network Connection.
Wi-Fi Connection – With the power adapter connected and the clock
mounted follow these steps to set up the connection. Note: A wireless
access point on the network is required.
From the CT clock touchpad tap Settings and enter the
administrator password and tap OK.
The Administrator Menu will display.
Tap Wireless and select Wi-Fi Networking On if it isn’t already.
A list of available wireless networks will display.
Select the desired wireless network, the WIFI Passcode screen
will display.
Using the master buttons to select upper case letters, lower case
letters, number or symbols enter the passcode for the wireless
network. Note: You may need to contact your network
administrator for wireless passcode information.
Tap OK when the passcode has been entered. A confirmation
message will display when connected.
Tap back until you have reached the main screen.
ABC @&%abc 123
Altri manuali per CT SERIES
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Lathem Terminale touch
Lathem
Lathem PayClock PC400TX Manuale operativo
Lathem
Lathem PAYCLOCK PC50 Manuale utente
Lathem
Lathem FACEIN Manuale utente
Lathem
Lathem CT SERIES Manuale utente
Lathem
Lathem PayClock PC600 Manuale utente
Lathem
Lathem PC600 Series Manuale utente
Lathem
Lathem PC700 Manuale utente
Lathem
Lathem PCPROX Manuale utente
