Lattice Semiconductor MachXO5-NX Development Kit Manuale utente

QuickART

MachXO5™-NX Development Kit

This document provides a brief introduction to the MachXO5™-NX Development Kit.

Check Kit Contents

The MachXO5-NX Development Board kit contains the following items:

MachXO5-NX Development Board

12 V AC/DC Adapter and International Plug Adapters

USB Cable for Programming via PC (USB-A to Mini-B)

Quick Start Guide

Lattice Radiant software download information

Using the MachXO5-NX Development Board

The MachXO5-NX Development Board as shipped supports Internal Flash boot-based

conguration. The internal Flash Conguration Memory is pre-loaded with a LED blink-

ing demonstration program.

Installing the software

The MachXO5-NX Development Board is pre-programmed with a basic demonstration.

To develop your own solutions, download and use the Lattice Radiant design software

(version 3.1 or later) in www.latticesemi.com/software.

If you only need to re-program the board, you can use the Radiant Programmer Stand-

alone software (version 3.1 or later).

Power

Switch

(SW6)

DIP

Switches

(SW1)

User LEDS

(D1~D8)

VS8 (J23)

VIOS (J25)

VS7 (J22)

VS6 (J21)

VS5 (J20)

VS3 (J26)

Power LED

(D18)

INIT LED

(D11)

Done LED

(D10)

Segment

LED Displayer

(D20)

MachXO5-25

Device (U3)

VS4

(J29)

Cong USB

Header (J11)

MachXO5™-NX Development Kit

Powering the Boards and Observing the Demo Program

Make sure that the following jumpers are installed already for selected power suppliers.

The USB cable should be connected from backside Mini-USB header J11 to a PC, and

switch LEFT the SW6 to power on the board. The following LEDs will light up indicating

the board is powered.

Conguration of the MachXO5-25 (U3) from the internal Flash memory is completed

almost immediately. After conguration.

Doing More with the MachXO5-NX Development Board

Check the Lattice website at www.latticesemi.com/MachXO5-NX-Development-Board

to download the full User’s Guide, the full source code of the default demo, and other

resources. You can use the Lattice Radiant software to develop and program your own

demos.

Additional Terms and Conditions Applicable to Lattice Programming and Development Hardware

Lattice device programmers, programming cables, socket adapters, and other hardware sold for use in conjunction with Lattice

software (“Programming Hardware”) and Lattice evaluation boards and development kits sold for use in conjunction with

evaluating Lattice products (“Development Hardware”) are designed and intended for use solely with semiconductor components

manufactured by Lattice Semiconductor Corporation. Programming and Development Hardware is warranted to meet Lattice

specications only for a period of ninety (90) days; in all other respects the terms and conditions of sale of Programming and

Development Hardware shall be Lattice’s standard terms and conditions set forth in Lattice’s Sales Order Acknowledgment.

Additionally, Lattice specications for Programming and Development Hardware limit their use to low-volume engineering

applications only, and not for volume production use. The warranty for Programming and Development Hardware will not apply to

any Programming or Development Hardware used in production, used with worn or improperly installed hardware, or used with

incompatible systems or components.

MachXO5TM-NX Development Kit

Jumper Pins to Connect

J20 Pin 1 to Pin 2 (VCCIO5 to 1.2 V)

J21 Pin 1 to Pin 2 (VCCIO6 to 1.2 V)

J22 Pin 1 to Pin 2 (VCCIO7 to 3.3 V)

J23 Pin 1 to Pin 2 (VCCIO8 to 3.3 V)

J25 Pin 1 to Pin 2 (VCCIO0/VCCIO2 to 3.3 V)

J26 Pin 1 to Pin 2 (VCCIO3 to 3.3 V)

J29 Pin 2 to Pin 3 (VCCIO4 to 1.2 V)

LED D18 Blue Light

LED D10 Green light indicate boot done

LED D11 Not light indicate no failure during boot

LED D1~D8 Red light illuminated in a repeating pattern

LED D20 All segments are blinking

Technical Support

www.latticesemi.com/support

(design) are either registered trademarks or trademarks of Lattice Semiconductor Corporation in the United States and/or other

countries. Other product names used in this publication are for identication purposes only and may be trademarks of their

respective companies.

QS067 V1

May 2022

Altri manuali per MachXO5-NX Development Kit

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lattice Semiconductor Microcontrollore

Lattice Semiconductor

Lattice Semiconductor MachXO2 Pico Manuale utente

Lattice Semiconductor

Lattice Semiconductor MachXO2-4000HC Manuale utente

Lattice Semiconductor

Lattice Semiconductor LatticeXP2 Manuale utente

Lattice Semiconductor

Lattice Semiconductor MachXO LCMXO2280C-4FT256C Manuale utente

Lattice Semiconductor

Lattice Semiconductor MachXO5T-NX Manuale utente

Lattice Semiconductor

Lattice Semiconductor HDR-60 Manuale utente

Lattice Semiconductor

Lattice Semiconductor HM01B0 UPduino Shield Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente