Lectrosonics DMTH4 Manuale utente

DMTH4

Digital Telephone Hybrid

INSTALLATION and QUICK START GUIDE

Rio Rancho, NM, USA

www.lectrosonics.com

Fill in for your records:

Serial Number:

Purchase Date:

DMTH4

LECTROSONICS, INC.2

Installation Guide

Rio Rancho, NM 3

Important Safety Instructions

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the

enclosure -- voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the

accompanying literature. Please read the manual.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and third grounding prong. The wider blade or

the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electri-

cian for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

15) WARNING -- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

DMTH4

LECTROSONICS, INC.4

Table of Contents

Important Safety Instructions .................................................................................................................................................................. 3

Table of Contents ...................................................................................................................................................................................... 4

Introduction ................................................................................................................................................................................................ 5

Unpacking the unit ................................................................................................................................................................................... 5

Controls and Features .............................................................................................................................................................................. 6

Front Panel ............................................................................................................................................................................................... 6

POWER On/Off Switch ........................................................................................................................................................................ 6

USB Port .............................................................................................................................................................................................. 6

Status LED ........................................................................................................................................................................................... 6

Rear Panel ............................................................................................................................................................................................... 6

POWER Plug........................................................................................................................................................................................ 6

RS232 Port ........................................................................................................................................................................................... 6

USB Port .............................................................................................................................................................................................. 6

Programmable Input and Output Ports ................................................................................................................................................ 6

Mode Switch ......................................................................................................................................................................................... 5

DANI ..................................................................................................................................................................................................... 5

TEL/CODEC RC .................................................................................................................................................................................. 5

Audio Inputs and Outputs .................................................................................................................................................................... 5

Telephone Set/Line .............................................................................................................................................................................. 5

Hardware Installation ................................................................................................................................................................................ 7

Installing the DM system into a rack ........................................................................................................................................................ 7

Cables ...................................................................................................................................................................................................... 7

Audio Connections ................................................................................................................................................................................... 7

Audio Inputs (AUX and CODEC) ............................................................................................................................................................. 7

Unbalanced Sources ............................................................................................................................................................................ 7

Balanced Sources ................................................................................................................................................................................ 7

Audio Outputs (AUX and CODEC) .......................................................................................................................................................... 8

Telephone Line Jack ................................................................................................................................................................................ 8

Programmable Inputs .............................................................................................................................................................................. 8

Programmable Outputs ............................................................................................................................................................................ 8

Expansion I/O ports ................................................................................................................................................................................. 9

CODEC and TEL Remote Control Ports ................................................................................................................................................. 9

Installing LecNet2™ Software and USB Driver ................................................................................................................................... 10

Installing LecNet2™ Software ............................................................................................................................................................... 10

Installing the LecNet2™ USB Driver ..................................................................................................................................................... 10

USB driver installation Windows XP ...................................................................................................................................................... 10

First Time Installation ......................................................................................................................................................................... 10

Installation of Additional Units (or LecNet 2™ devices) .................................................................................................................... 11

USB Driver Installation (Windows 2000) ............................................................................................................................................... 12

First Time Installation ......................................................................................................................................................................... 12

Basic System Setup ................................................................................................................................................................................ 13

Control System Interconnections .......................................................................................................................................................... 13

Initial Setup ............................................................................................................................................................................................ 13

Master/Slave Configuration ................................................................................................................................................................... 14

Using the DMTH4 Control Panel to Change Master/Slave Mode ......................................................................................................... 14

Initial Setup Hints ................................................................................................................................................................................... 15

Example Teleconferencing Setup .......................................................................................................................................................... 16

Setting up the DMTH4 Main Matrix ....................................................................................................................................................... 17

Setting up the DM1624 Main Matrix ...................................................................................................................................................... 17

Setting up the DM1624 Expansion Matrix ............................................................................................................................................. 17

Setting up the DMTH4

Output Source Multiplexer ................................................................................................................................................................. 18

Basic System Operation ......................................................................................................................................................................... 19

Making a Phone Call ............................................................................................................................................................................... 19

Make a Telephone Call Using a Telephone Set ..................................................................................................................................... 19

Make a Telephone Call Using the Activity Tab ...................................................................................................................................... 19

Using the Touch Tone Pad ..................................................................................................................................................................... 19

Use the “Type the number to dial” box ................................................................................................................................................... 20

Use the Phone Book .............................................................................................................................................................................. 20

Setting Up Automatic Telephone Answer and Automatic Disconnect ................................................................................................... 20

Connecting to the CODEC Interface using the Activity Tab .................................................................................................................. 21

FCC Part 68 Compliance ....................................................................................................................................................................... 22

FCC Part 15 Compliance ....................................................................................................................................................................... 22

Warranty .................................................................................................................................................................................. Back Cover

Installation Guide

Rio Rancho, NM 5

Introduction

The purpose of this guide is to assist in the setup and

operation of a typical DMTH4 system. This guide

assumes familiarity with the DM Series Digital Audio

Processors, its components and software menus and

setup screens. To get the most out of the DMTH4

system, it is suggested to review the information

presented in the DMTH4 Series Reference Manual.

A detailed Help is also available to assist in the setup

and operation of a DMTH4 system using the USB

interface and a Windows® 2000 or Windows®XP

computer system. In addition to assistance setting up

and operating the DMTH4 system, the Help files include

a complete listing of the DMTH4 Serial Commands.

These commands can be used to setup and operate

the DMTH4 system via external devices using either the

USB or RS232 serial port.

Unpacking the unit

Compare the packing list enclosed with the unit with the

original order. Inspect all items for damage. Immedi-

ately call 1-800-821-1121 to report any items that are

missing or damaged. The sooner we get notified, the

sooner we can get any needed replacement items

shipped to your location.

DMTH4

LECTROSONICS, INC.6

TELEPHONE

SET LINE

EXPANSION TEL RC

1: GND

2: IN 1

3: IN 3

4: IN 5

5: IN 7

25

13

14

1

6: IN 9

7: IN 11

8: GND

9: OUT 1

10: OUT 3

11: OUT 5

12: OUT 7

13: GND

14: +5V

15: IN 2

16: IN 4

17: IN 6

18: IN 8

19: IN 10

20: +5V

21: OUT 2

22: OUT 4

23: OUT 6

24: OUT 8

25: +5V

PROGRAMMABLE

INPUTS / OUTPUTS

RS-232

LecNet 2

USB

POWER

90-240V 50/60Hz 15W

AB

TELEPHONE HYBRID

MADE IN U.S.A.

TX RX

RX TX

CODEC RC

CODEC AUX CODEC AUX

U.S. Patent Number: 5,414,776

LINE

INPUTS

MIC/LINE

OUTPUTS

LECTROSONICS, INC.

Complies with Part 68 FCC rules.

Registration Number:4J3BR09BDMTH4

Ringer Equivalence: 0 . 9 B

This device complies with

Part 15 of the FCC rules.

Operation is subject to the

following two conditions: (1)

This device may not cause

harmful interference, and (2)

this device must accept any

interference received, including

interference that may cause

undesired operation.

Controls and Features

POWER On/Off Switch

The Power On/Off Switch is used to turn the DMTH4 on

(1) or off (0).

USB Port

Standard USB connector for the setup and control of a

DMTH4 from an Windows 2000 or Windows XP com-

puter system with USB interface.

Status LED

The DMTH4 is normally configured as the end slave

unit in a DM Series stack. In this configuration, the

Status LED glows steadily when power is applied and a

Master unit has been detected. The STATUS indicator

will blink to indicate that it has not found the Master unit

or some other error exists.

Note: The DMTH4 is shipped from the factory

configured as a Master unit. In this mode, the

Status indicator glows steadily when power is

applied.

Mode Switch

If a unit configured to run in Slave mode doesn’t detect

a master unit on powerup, it will refuse to boot up and

the Status LED will blink rapidly. In this case, pressing

the Mode switch will force the unit to boot up tempo-

rarily in Master mode to allow settings to be examined

or changed. Cycling the power returns the DMTH4 to

Slave mode.

Pressing the Mode switch while powering up the

DMTH4, places the unit in Software Update mode. The

Status LED blinks slowly while the firmware is updated,

then extinguishes when the process is complete.

Cycling power exits Software Update mode.

Front Panel

Rear Panel

POWER Plug

Standard NEMA 5-15 three-pin power plug capable of

accepting 100-240 VAC, 47-63 Hz.

RS232 Port

A serial RS232 interface provided for setup and control

via computer serial port, or for connecting RS-232

serial control devices from other companies.

USB Port

Standard USB connector for the setup and control of a

DMTH4 from an Windows 2000 or WIndows XP com-

puter system with USB interface.

Programmable Input and Output Ports

Programmable inputs or outputs used to enable control

over a variety of parameters or to indicate the current

state of a programmable input.

DANI

DANI, or Digital Audio Network Interface, is used to

route the digital audio signals passing between the

master and slave units in stacked configurations.

TEL/CODEC RC

These interfaces are used to connect RCWTH4 remote

control units.

Audio Inputs and Outputs

Analog audio input and output connectors for Codec

and Aux ports .

Telephone Set/Line

RJ11 jacks for connecting a standard telephone line

and a single-line telephone set to the DMTH4.

POWERUSBSTATUSMODE

TELEPHONE HYBRID INTERFACE

R

POWER On/Off SwitchUSB PortStatus LEDMode Switch

POWER Plug RS232 USB Programmable

Input and Output

Ports

DANI

Tel RC

Line Inputs

(Codec/Aux)

Telephone

Set/Line

Mic/Line Oututs

(Codec/Aux)

Codec RC

Installation Guide

Rio Rancho, NM 7

DM In

+

-

Source

+

Unbalanced source to DM input

(3-Wire)

Shield

DM In

+

-

Source

+

Unbalanced source to DM input

(2-Wire)

Shield

Balanced source to DM input

(3-Wire)

DM In

+

-

Source

+

-Shield

Installing the DM system into a rack

The DMTH4 occupies a single space. There are no

special ventilation requirements. Mount with 4 rack

screws using the appropriate mounting holes. It is

recommended to use nylon washers to prevent damage

to the front panel’s finish when tightening the screws.

For North American installations, connect the Power

Cable supplied with the unit between the DMTH4 and a

stable power source. All DM processors have internal

switching power supplies that can tolerate voltages

ranging from 100 VAC to 240 VAC. Use an approved

power cable for installations outside North America.

Cables

It is recommented to use lacing bars for cable strain

relief when mounting in a rack. Use only professional

audio cable with proper shielding - typically, two con-

ductor plus ground/shield.

Audio Connections

The analog audio inputs and outputs are connected

through 5 pin de-pluggable connectors. Strip the

insulation back 1/8 to 3/16" but do not tin (apply solder

to) the leads. Insert the wire into a de-pluggable

connector, leaving less than 1 mm of bare wire ex-

posed, then tighten the retaining screw.

Caution: Do not over tighten the retaining

screw.

Note the labeling on the DMTH4 Chassis for the

positive and negative leads. Ground is shared between

two connections (the center pin).

Note: The DM Series does not have a “pin 1

problem.” Inputs and outputs are true differential

connections.

Audio Inputs (AUX and CODEC)

Unbalanced Sources

Unbalanced audio sources (positive and ground)

include items such as consumer VCR’s, DVD players,

etc., and may use both two wire and three wire cables.

In either case, the positive output from the source

should be connected to the appropriate positive (+)

input on the DMTH4. The shield or negative (–) output

should be connected the DM’s negative (–) input. Two

wire cables should have a jumper between the DMTH4

negative input and ground. Three wire cables should

have the shield connected to the DMTH4’s ground input

and the shield and negative (–) leads joined together at

the unbalanced source end.

Balanced Sources

Balanced differential sources from external equipment

and microphones should be wired according to Bal-

anced source to DM input (3-Wire). (See illustration.)

When connecting balanced sources to the DMTH4, it is

important to not connect chassis ground (shield) to

either signal conductor.

Hardware Installation

5-pin depluggable

connector

Do not leave more than 1

mm of exposed wire

beyond the connector.

Do not apply

solder to leads

Retaining Screw

(Do not overtighten)

DMTH4

LECTROSONICS, INC.8

LED ison when the programmable output isactive

380 Ohms

Programmable Output Pin

380 Ohms

LED isoff when the programmable output isactive

Programmable Output Pin

Gnd (from Programmable I/O

Pins1, 8, 13)

1N4001

or equiv.

External

DC Voltage

Source

(<40VDC)

Relay Coil

Coil current <100mA

Programmable Output Pin

Gnd (from Programmable I/O

Pins1, 8, 13)

Relay ison when the programmable output isactive

+5VDC (from Programmable I/O

Pins14, 20, 25)

+5VDC (from Programmable I/O

Pins14, 20, 25)

10K Linear Potentiometer

CCW CW

+5V

To Programmable Input Pin

Gnd

Contact Closure as Programmable Input

To Programmable Input Pin

Gnd

DC Voltage Source as Programmable Input

To Programmable Input Pin

0VDC (Off) to +5VDC (On)

Gnd

Potentiometer Connection for

Analog Control of Gain

Output RP Gain Control

on the Programmable

Inputs control tab in the Control Panel GUI. See the

Rear Panel Ctrl tab in the Control Panel software Help

for setting all programmable input parameters.

Programmable Outputs

Programmable outputs are used to indicate the current

state of a programmable input, monitor activity on

telephone or codec interfaces, and monitor active

preset changes. Each programmable output is the

electrical equivalent of a contact closure to ground.

When a programmable output is “active”, it conducts

current to ground. When the programmable output is

“inactive”, no current flows to ground. The maximum

usable voltage for the programmable outputs is 40 V

and they will safely conduct up to 100 mA DC continu-

ous. Following are some typical uses for the program-

mable outputs.

Audio Outputs (AUX and CODEC)

The AUX and Codec outputs are a balanced differential

configuration and include an attenuator to reduce the

signal to mic level. Wire these outputs as indicated in

the following illustration.

Telephone Line Jack

Connect a standard telephone cable with RJ11 connec-

tors between the back panel Telephone Line Jack and

the host telephone system.

Programmable Inputs

Programmable inputs are provided to enable external

control over a variety of parameters. Each input can

respond to a contact closure, a DC voltage source, or

the variable voltage output from a potentiometer. The

following illustrates common connections to the pro-

grammable input pins. (See also Programmable

Inputs and Outputs Wiring Example.)

No external pull-up resistors are necessary because

each programmable input is internally pulled up through

a 100K resistor to +5V. When using a continuous

voltage with one of the programmable inputs, the

function of the programmable input must be set to

either

Analog Input RP Gain Control

or

Analog

DM Out

+

-

Destination

+

-

DM Out to Balanced Input

(3-Wire)

Shield

DM Out

+

-

Destination

+

DM Out to Unbalanced Input

(3-Wire)

Shield

DM Out

+

-

Destination

+

DM Out to Unbalanced Input

(2-Wire)

Shield

Installation Guide

Rio Rancho, NM 9

Note: The diagram shows an external DC source

powering the relay coil. This is necessary

whenever coil voltages exceed 5 V.

Both LEDs and 5V relay coils can be powered by the +5

V DC pins on the programmable input connector, as

long as the maximum combined current for all LEDS

and relay coils does not exceed 100 mA.

Expansion I/O ports

The four RJ45 connectors on the rear panel are used to

interconnect LecNet2™ units together. These ports are

only used to transfer digital audio information via the

Digital Audio Network Interface (DANI) between the

units.

PROGRAMMABLE INPUTS/OUTPUTS

1 - GND

2 - IN 1

3- IN 3

4 - IN 5

5 - IN 7

6 - IN 9

7 - IN 11

8 - GND

9 - OUT 1

10 - OUT 3

11- OUT 5

12 - OUT 7

13- GND

14 - +5V

15 - IN 2

16 - IN 4

17 - IN 6

18 - IN 8

19 - IN 10

20 - +5V

21 - OUT 2

22 - OUT 4

23- OUT 6

24 - OUT 8

25 +5V

113

ccw cw ccw cw

ON OFF

OUT 3

OUT 4

OUT 1

IN 1

IN 2

IN 3

500 Ohms

LED

Potentiometer

Switch

Programmable Inputsand

OutputsWiringExample

Three Programmable Inputs:

2 - 10 K linear potentiometers

for volume control

1 - Tobble switch for muting

3Programmable Outputs:

LEDSfor function indicators

(380 to 500 Ohm resistorsin-line

to avoid burning out LEDS)

NOTE

Common Connectionscan be used for

all voltage and ground connections

amongall devices.

CODEC and TEL Remote Control Ports

WARNING:

The Expansion I/O connectors are

NOT

Ethernet, CobraNet or any other network

based device interconnects. Connecting them

to Ethernet, CobraNet or other network based

device may cause damage to either unit.

In a stacked configuration, one unit must be configured

as the Master unit and the others as Slave units. The

DMTH4 is normally configured as the last Slave unit in

a DM Series chain.

To connect the Master/Slave units, plug one end of a 12

inch Cat5e cable (two are supplied with each with unit)

to the transmit (TX) port on the Master unit, and con-

nect the other end to the corresponding receiver (RX)

port on the Slave unit immediately below the Master.

Repeat this procedure with the second Cat5e cable.

CAUTION: Do not connect these ports to each

other on a single unit, and to not cross the

cables between the units.

1 GND

2 Connect Button

3 Privacy Button

4 Volume Up Button

5 Volume Down Button

6 Privacy LED

7 Connect LED

8 GND

Expansion I/O Ports (DANI Bus)

CODEC and TEL Remote Control Ports

Expansion Port Digital Audio Network Interface

Interconnection Diagram

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

LINE OUT

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

LINE OUT

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

LINE OUT

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

PROGRAMMABLE

INPUTS/ OUTPUTS

1- GND

2- IN 12

3-IN 14

4- IN 16

5- IN 18

6- IN 20

7- IN 22

8- GND

9- OUT 9

10- OUT 11

11-OUT 13

12- OUT 15

13-GND

14- +5V

15- IN 13

16- IN 15

17- IN 17

18- IN 19

19- IN 21

20- +5V

21- OUT 10

22- OUT 12

23-OUT 14

24- OUT 16

25- +5V

- + - +

TX

RX

1- GND

2- IN 1

3-IN 3

4- IN 5

5- IN 7

6- IN 9

7- IN 11

8- GND

9- OUT 1

10- OUT 3

11-OUT 5

12- OUT 7

13-GND

14- +5V

15- IN 2

16- IN 4

17- IN 6

18- IN 8

19- IN 10

20- +5V

21- OUT 2

22- OUT 4

23-OUT 6

24- OUT 8

25- +5V

A B

EXPANSION

15

16

13

14

17

18

19

341 2 5 6 7

LINE OUT

MasterSlaveMasterSlave

DMTH4

LECTROSONICS, INC.10

Installing LecNet2™Software and USB Driver

LecNet2™ is a Graphic User Interface (GUI) designed

to allow easy setup and monitoring of DM components

using Windows®2000 or XP computer systems.

LecNet2™ includes the necessary Control Panels to

configure and monitor all the DM series products plus

the Venue Modular Receiver system.

Installing LecNet2™Software

1. Use the computer system’s control panel to remove

any previously installed versions of LecNet2™

software. (This will ensure you are using the latest

release.)

2. Insert the LecNet2™ program disk supplied with

your system into the computer system’s CD-ROM

drive.

3. The CD should automatically start the installation

procedure. If it doesn't, click "Start" on the

WIndows Task Bar then click "Run..." Enter the

Drive number followed by "Setup.exe" then click

OK.

4. Follow the on-screen instructions to install the

LecNet2 software.

Installing the LecNet2™USB Driver

There are two methods of connecting a Windows®-

based computer system to the DM component, either

via a USB cable or an RS-232 cable. Although the USB

port offers significantly increased speed and conve-

nience over standard RS-232 links, it does require the

installation of a LecNet2™ USB driver.

The LecNet2 USB driver is not part of the standard

Windows®2000 and XP driver libraries. As a result,

connecting a computer system to a DM system for the

first time is different than subsequent installations.

There are a few minor differences between installing

the LecNet2 USB drivers on a Windows 2000 versus a

Windows XP system.

USB driver installation Windows XP

First Time Installation

When a LecNet2™ device is connected to the PC for

the very first time, the Windows Found New Hardware

Wizard automatically opens. Use the following proce-

dure to install the LecNet2™ USB driver using the

Wizard.

1. Place the LecNet2™ Installation Disk in the PC’s

CD-ROM drive.

2. On the first page of the Wizard, select the option

Install from a list or specific location (Ad-

vanced) and click Next> to continue.

3. Select "Search for the best driver in these

locations", then check "Search removable media

(floppy, CD-ROM...)" and click Next> to continue.

4. Windows searchs the CD for the driver and when it

has found it, it is likely that a dialog will open

warning you that the driver has not passed Win-

dows Logo Testing, click Continue Anyway.

Lectrosonics DMTH4 Manuale utente

Manuali Sistema telefonico popolari di altre marche