LEGRAND Radiant Series Manuale utente

installation guide

Smart Switch

WTRL10

table of contents

before you start..................................3

what you need ...................................4

installation and setup ................ 6–19

getting to know your switch ......20-21

specifications...................................22

faqs ..............................................23

regulatory information......... 24–27

warranty.......................................28

support ........................................29

before you start

Review this guide in its entirety before beginning device installation. Consult an

electrician with any questions or if you are unsure of your abilities.

DWarning: Incorrect installation could

result in death, serious injury, and/or

damage to your home or devices.

DCaution: To reduce the risk of injury

and/or overheating and damage to other

equipment:

• For dry, indoor use only.

• Do not use to power medical equipment.

• Not suitable as a disconnecting means.

• Do not use with loads exceeding the

device load rating (see page 22).

• Connect the smart switch to a

120 VAC, 60 Hz power source ONLY.

• Always use copper wire to install the

smart switch and follow all applicable

local and national electrical codes.

• Install in a non-metallic electrical box

to protect wireless signal strength.

Visit the Legrand website at www.legrand.us/radiant/smart-lighting.aspx to learn more

about your smart device.

what you need

REQUIRED:

Phillips-head screwdriver

Flat blade screwdriver

YOU MAY ALSO NEED:

Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,

ﬂashlight, radiant®screwless wallplate (included), wiring leads (included), and

wire nuts (included)

NOTE: Exercise caution when using power tools. Overtightening the screws can

damage the device.

installation & setup

step one

turn off the power for your device at the

circuit breaker

Flip the existing light switch multiple times to conﬁrm the power is off.

NOTES:

• If there are multiple devices next to your existing light switch, make sure power is

off at the circuit breaker for all of those devices.

• For three-way installations using a remote switch, follow the instructions for the

remote device (WTRL20).

OFF

installation & setup

step two

remove the existing device

Check for the following wires:

1HOT or LINE: Receives power from the circuit box. Referred to as “Hot” for the

purposes of this guide.

2LOAD: Directs power to your light(s).

3NEUTRAL: Creates a path to return current to the power source when the

device is off. Required for your switch installation.

4GROUND: Provides a safe path for electricity in the event of a short circuit.

NOTE: Refer to “faqs” on page 23 if you are unsure of your wiring.

OFF

VOLTAGE

TESTER

Load

Supply

“Hot”

installation & setup

step three

wire the smart switch

When connecting each wire, loosen the terminal screw, insert the wire into a

terminal slot, and tighten the terminal screw until the wire is secured.

1Connect the neutral wires to the WHITE terminal slots.

2Connect the load wire to any LOAD terminal slot.

3Connect the hot wire to any HOT terminal slot.

4Connect the ground wire to the green wiring lead on the device. Use a wire nut

to secure the wires together.

NOTE: If you need extra length on your wires, wire leads are included in your packaging.

Altri manuali per Radiant Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LEGRAND Interruttore

LEGRAND

LEGRAND LEXIC AstroRex DY64 Manuale utente

LEGRAND

LEGRAND Wattstopper CS-50 Manuale utente

LEGRAND

LEGRAND adorne WNAL23W1 Manuale utente

LEGRAND

LEGRAND Wattstopper HDLS1SS Manuale utente

LEGRAND

LEGRAND Arteor 5720 83 Manuale utente

LEGRAND

LEGRAND 882 09 Manuale utente

LEGRAND

LEGRAND AM5659 Manuale utente

LEGRAND

LEGRAND PRO 21 7756 27 Manuale utente

LEGRAND

LEGRAND 036 12 Manuale utente

LEGRAND

LEGRAND radiant RCD113 Manuale utente

LEGRAND

LEGRAND DMX3 Manuale operativo

LEGRAND

LEGRAND PX3 Manuale utente

LEGRAND

LEGRAND Pass & Seymour OSR300S Manuale utente

LEGRAND

LEGRAND 0 488 07 Manuale utente

LEGRAND

LEGRAND Raritan Secure Switch Series Manuale utente

LEGRAND

LEGRAND 0 672 33 Manuale utente

LEGRAND

LEGRAND LEXIC 037 23 Manuale utente

LEGRAND

LEGRAND Luxul AGS-1024 Manuale utente

LEGRAND

LEGRAND 4128 58 Manuale utente

LEGRAND

LEGRAND radiant WWRL10WHCCV2 Manuale utente

LEGRAND

LEGRAND Wattstopper AS-100-A Manuale utente

LEGRAND

LEGRAND 300 W RF Manuale utente

LEGRAND

LEGRAND HKRL10 Manuale utente

LEGRAND

LEGRAND In One Plexo 695 10 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente