LEGRAND Daker DK 4.5-6 kVA Manuale utente

Part. LE08927AA-09/15-01 GF

Daker DK 4.5-10 kVA

Parallel installation quick start

ENGLISH 3

Daker DK 4.5-10 kVA

Index

Introduction 2

1 Important Safety Instructions 2

2 Parallel system installation 3

3 Single Unit Check 5

4 Parallel Setting 7

4 Parallel Mode Start up 8

5 Trouble Shooting 9

Introduction

1 Important Safety Instructions

This document is a reference guide to install the Daker DK UPS 4,5-10kVA in parallel for N+1

redundancy operation. The parallel installation and configuration procedure is divided in 4 phases :

Parallel system installation – To physically connect each unit.

Single Unit check – To verify and confirm that each unit works properly with the correct

parameters and output voltage

Parallel Setting – To setup each units’ parameters to work in parallel mode.

Parallel Mode Start up – To verify that the parallel system works normally.

• Only qualified and trained electricians are allowed to install the UPSs in single unit or parallel

systems.

• Please read the Installation guide carefully before installing these UPSs to avoid electrical

hazards or damages to the UPS and the loads connected.

• To prevent potential leakage current hazard, ensure that the AC main supply is securely grounded.

• Please note that the Parallel function of the UPS can be enabled only in“Normal Mode”operation.

• Before to set a parallel installation, ensure that the output voltage tolerance for each UPS at

zero-load condition is less than 0.5Vac.Please consult your authorized dealer if any of the UPS

output voltage has the tolerance over 0.5Vac.

• Ensure that the communication cables plugged into the UPS RJ45 connectors are connected

securely to avoid damage to both the UPS and the output devices.

• Ensure that two and only two UPS units of the parallel system have the terminal resistors on the

rear set in “On” position.

• Only UPS with the same rating and type can be installed in parallel.

• Please ensure to add a 40Arms/250Vac and 30Arms/250Vac NFB(Non-fuse Breaker)at the input

and output of each UPS respectively.

Daker DK 4.5-10 kVA

2 Parallel system installation

ACCESSORIES DESCRIPTION QUANTITIES

2 UPS 3 UPS 4 UPS

Standard cat5 cable

with Rj45 connector

(max length: 1050mm)

x 1 x 2 x 3

Standard cat5 cable

with Rj45 connector

(max length: 1900)

x 1

F1 Bracket to secure

C1 and C2 to the UPS box x 2 x 3 x 4

Accessories

The following accessories (included in the parallel kit) are requested to install the UPS in parallel mode.

• The design of the air flow for the convertible UPS is to flow in from the front ventilation holes

to the rear ventilation holes.

It is recommended to leave at least 30 cm around the UPS and Battery bank to allow good

ventilation conditions.

Please refer to the UPS manual for the detailed installation guide.

• To reduce noise interference do not cross or mix input , output, and battery cables.

• Please install the communication wires for parallel and control signal functions (including

cat5, serial, usb and EPO cables) keeping them away from input/output and battery cables.

• To prevent potential leakage current hazard, ensure that the AC main supply is securely

grounded.

• Please refer to the single UPS input/output current specifications and recommended conduc-

tors listed below:

AC input and output

MODEL MAXIMUM CURRENT CONDUCTOR SECTION

4,5-6KVA 33A AWG #9

10KVA 54,3A AWG #7

Battery Input

MODEL MAXIMUM CURRENT CONDUCTOR SECTION

4,5-6KVA 25A AWG #10

10KVA 41A AWG #10

Recommended Circuit Breakers to be installed at the UPS input/output

MODEL INPUT CBi OUTPUT CBo

4,5-6KVA 40A 30A

10KVA 63A 63A

The breaker type should be “C” or “D” with the following current ratings:

• Install and connect the UPS units according to the diagrams in figure 2, 3, 4, 5.

CAUTION

The MTBS is an optional for maintenance.

2 Parallel system installation

CBi : installation input breakers

CBo : installation output breakers

CB1 : UPS utility input breaker

Utility input

UPS output

Figure 1

Daker DK 4.5-10 kVA

1050mm RJ-45

communication

connecting wire

1900mm RJ-45

communication

connecting wire

Max. 25M; all Input

Power cables shall

be with the same

lenght

Figure 2 Figure 3

Figure 4

1900mm RJ-45

communication

connecting wire

• Connect the parallel CAT5E cables as a “Ring Network” (Figure 3) using the parallel kit plate to

fix them to the UPS rear panel (Figure 4)

2 units parallel

3 units parallel

4 units parallel

CAUTION

The maximum length of the communication connecting wires shall be less than 7M.

All the Input/ output power cable should have the same length (max 25m)

Parameters Check

CAUTION

The following operations have to be done on each UPS separately and independently.

• Ensure that all the circuit breakers at the input (Cbi) and output (Cbo) are set to off position.

• Ensure that all the utility input breakers (CB1) for each UPS is set to off position

• Turn on the AC input of the UPS to be checked :

Turn on only the input breaker CBi connected to the UPS to be checked, and the utility breakers

CB1 on the rear panel of the UPS itself. DO NOT TURN ON THE INVERTER !

Figure 5

• Enter in setting mode by pressing <On> & < > keys simultaneously for 3 seconds (Figure 6).

• Verify that all the UPS’s parameters match with the default values (Table 1)

3 Single Unit Check

Daker DK 4.5-10 kVA

Item

Press < >

to change

Display List

Default Press < > to change

Buzzer on/off

Self-Test

(Available in Line-Mode Only)

Bypass Voltage

Range

Inverter Synchronize

Frequency range

Inverter

Output Voltage *

Operation Mode

Output Voltage

Adjustment

Parallel ID

Number **

Parallel Function

On/Off ***

SAVE Press < > to Save

After Saved

UPS Locked Shut off AC input power to reset the UPS

Table 1

** Single unit ID number must be “01”, or UPS will have an Er17 error occurred.

*** Single unit Parallel function must be “OFF” (P 01), or UPS will have an Er21 error occurred.

3 Single Unit Check

CAUTION

“Bypass Voltage Range”, “Inverter Synchronize Frequency Range”, “Inverter Output Voltage”

and“Output Voltage Adjustment“ are adjustable parameters but for parallel function eve-

ry unit must have the same settings

• Change item by pressing < > until the display shows the text “Save”. Press < Enter > to save the

setting.

• Turn off the UPS utility input breaker (CB1) while the LCD shows “LINE OFF” to reset the UPS.

Basic Function Check

• Turn on the AC input (UPS utility input breaker) and then turn on the UPS inverter (press <ON>)

• Test the UPS switching from normal mode to stored energy mode and viceversa

• Verify that the LCD panel works normally and doesn’t display errors.

Output Error Voltages Check

• Verify the output voltage for each UPS unit (at 0 load), and make sure the voltage difference

between each unit is under 0.5Vac.

• If the voltage difference is between 0.5~1.0Vac, the parallel error current will be higher.

• If the voltage difference is over 1.0Vac, a calibration should be performed on the unit(s) which

has over-limit error voltage otherwise the parallel could fail (If this condition occurs please con-

tact your local dealer for technical support)

Turn off the inverter (press <off>) and then the AC input (Turn off CBi and the UPS utility input

breaker) and restart the process for the next unit.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LEGRAND UPS

LEGRAND

LEGRAND Keor SPE 750 Manuale utente

LEGRAND

LEGRAND PREMIUS Manuale operativo

LEGRAND

LEGRAND CS102 Manuale utente

LEGRAND

LEGRAND KEOR DC Manuale utente

LEGRAND

LEGRAND DAKER DK Plus 3 101 71 Manuale utente

LEGRAND

LEGRAND DAKER DK Plus Series Manuale utente

LEGRAND

LEGRAND KEOR MOD Manuale utente

LEGRAND

LEGRAND Niky 1000 Manuale utente

LEGRAND

LEGRAND KEOR TOWER SPE Manuale utente

LEGRAND

LEGRAND STARK 10 kVA Manuale utente

LEGRAND

LEGRAND Keor MOD Series Manuale utente

LEGRAND

LEGRAND NUMERIC Onfiniti Manuale operativo

LEGRAND

LEGRAND NUMERIC HP i 33 40 kVA Series Manuale utente

LEGRAND

LEGRAND Keor MOD Series Manuale

LEGRAND

LEGRAND KEOR PDU Series Manuale utente

LEGRAND

LEGRAND KEOR MOD Manuale utente

LEGRAND

LEGRAND Ekinoxe 327 13 Manuale utente

LEGRAND

LEGRAND MyHOME F455 Manuale utente

LEGRAND

LEGRAND Archimod HE 240 Manuale

LEGRAND

LEGRAND Keor MOD Top Entry Manuale utente

LEGRAND

LEGRAND DAKER DK Plus 3 101 73 Manuale utente

LEGRAND

LEGRAND KEOR LINE RT1500 VA Manuale utente

LEGRAND

LEGRAND KEOR SPE TOWER Series Manuale utente

LEGRAND

LEGRAND KEOR HP Series Manuale di installazione

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente

ZincFive

ZincFive BC Series Manuale utente