Leister Hot-Jet S Manuale utente
1
LEISTER Hot-Jet S
Hot Air Welding Tool
Please read operating instructions carefully
before use and keep for further reference.
•Soldering and de-soldering of SMD thru-hole components.
•Welding of thermoplastic materials and also single-ply flexible plastics and
modified bitumen in the form of boards, tubes, profiles, lining membranes,
coated materials, films, foams, tiles, and sheets. The following procedures
are possible: overlap welding, welding with rod, with tape and fusion
welding by heat.
•Shrinking of heat-shrink sleeves, films, tapes, solder sleeves and moulded
parts.
•Activating/dissolving of solvent free adhesives and fusion adhesives.
•Drying of water-damp surfaces.
GB
OPERATING INSTRUCTIONS
APPLICATION
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41- 41 662 74 74 Fax +41- 41 662 74 16
www.leister.com [email protected]
®
Voltage V~
Power consumption W
Temperature °C
Air flow l/min.
Air pressure mbar
Noise level dB (A)
Weight g
Size mm
100, 120, 230, for 50/60 Hz
460, 460, 460
20 – 600, steplessly controlled
20 – 80, steplessly adjustable
max. 16
59
375 without cable, 580 with 3m cable
235 x 70, handle Ø 40
2
Mains voltage
cannot be
switched over
TECHNICAL DATA Electrical safety: double insulated
This tool is CCA certificated (CENELEC Certification Agreement).
Danger to life when opening the tool, as live compo-
nents and connections ar exposed. Unplug the tool
before opening it.
Incorrect use of hot air blowers can cause fire and
explosion hazard, especially near combustible materials
and explosive gases.
The tool must be operated with supervision. Warmth
can reach combustible materials, which are out of sight.
For personal protection on building sites we strongly
recommend the tool be connected to a GFCI (Ground
Fault Circuit Interrupter) or a RCCB (Residual Current
Circuit Breaker) .
The voltage rating stated on the tool must correspond to
the line/mains voltage.
Do not touch the element housing and nozzle when
they are hot as they can cause burns. Let the tool cool
down. Do not point hot air flow in the direction of
people or animals.
Protect tool from damp and wet.
FI
120
230
WARNING
CAUTION
APPROVAL MARKS
Description of tool
Operating condition
• As required, push-fit appropriate nozzle (9).
•Connect tool to the mains.
• The air flow is steplessly adjustable by use of the black potentiometer (4).
•The hot air temperature is steplessly adjustable by use of the red potentiometer (3).
•If required, earth the tool via the ESD-lead connection.
•Switch on (2) and allow to warm up for about 5 min.
Operation
•The Leister Company, as well as the Service Centres, offer free training courses in
all areas of application (see page 1).
Change of nozzles
• Before changing nozzles, allow the tool to cool down, or use only combination
pliers.
•Do not touch hot nozzle (9) and make sure to put it only on a heat resistant sur-
face, because of the fire hazard.
•The nozzles are easily pushed onto the tapered element housing (8) and are then
secured by fastening the screw on the clamp (10).
•Only Leister nozzles should be used.
3
USAGE LEISTER Hot-Jet S
1. Cable to mains
2. On/off switch
3. Potentiometer for
temperature adjustment
4. Potentiometer for
air flow adjustment
5. Air filter
6. Handle
7. Rubber stand
8. Element housing
9. Nozzle
10. Clamp with screw
to push-fit nozzle
11. ESD-lead connection
12. Tool stand (wich can
be rotated and fixed).
685
711 12 234
19
10
4
BA HOT-JET S/ 06.2001/GB
•The welding tool's airfilter (5) should be cleaned with a brush if nescessary.
•A wire brush should be used for cleaning the welding nozzle (9).
•Use only LEISTER accessories.
•The carbon brushes of the motor have to be checked by your Service Centre
after about 700 hours running time.
•Repairs should only be carried out by authorised LEISTER Service Centres.
They guarantee a specialised and reliable Repair Service within 24 hours using
original spare parts lists.
•Guarantee and liability are in accordance with the guarantee certificate as
well as with the currently valid general business and sales conditions.
•LEISTER Process Technologies rejects any guarantee claims for tools which are
not in their original condition. The tools must never be altered or changed.
Technical data and specifications are subject to change without prior notice.
Your authorised Service Centre is:
GUARANTEE AND LIABILITY
SERVICE AND REPAIRS
ACCESSORIES
MAINTENANCE
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41- 41 662 74 74 Fax + 41- 41 662 74 16
www.leister.com [email protected]
®
Altri manuali per Hot-Jet S
1
Indice
Altri manuali Leister Sistema di saldatura
Leister
Leister GEOSTAR G5 LQS Manuale utente
Leister
Leister SEAMTEK 2000 AT Manuale utente
Leister
Leister BITUMAT B2 Manuale utente
Leister
Leister VARIANT T1 Manuale utente
Leister
Leister VARIMAT V2 Manuale utente
Leister
Leister SEAMTEK 900 AT Manuale utente
Leister
Leister Uniplan Wedge Manuale utente
Leister
Leister VARIMAT V2 Series Manuale utente
Leister
Leister UNIROOF E 40 mm Manuale utente
Leister
Leister WELDPLAST S1 F Manuale utente
Leister
Leister TRIAC BT Manuale utente
Leister
Leister Twinny T Manuale utente
Leister
Leister FUSION 3C Manuale utente
Leister
Leister TRIAC BT Manuale utente
Leister
Leister PENWELD A Manuale utente
Leister
Leister FUSION 3 Manuale utente
Leister
Leister WELDY foiler Manuale utente
Leister
Leister FUSION 2 Manuale utente
Leister
Leister WELDPLAST S2 Manuale utente
Leister
Leister TAPEMAT Manuale utente
