Lenz Digital plus lh01 Manuale utente

B.B.10.0021

Information LH01

Art. no. 21010

2nd version 0515

2 Information LH01

Table of contents

1Welcome! ........................................................................................ 4

2Important advice, please read first! ................................................ 5

3Overview of the features of the LH01 ............................................. 6

4Operating elements of the LH01..................................................... 9

5Connection and initial operation ................................................... 10

6Emergency shutdown ................................................................... 12

7Controlling locomotives................................................................. 13

7.1 Changing the speed step....................................................... 13

7.2 Changing the direction of travel / Emergency stop................ 14

8Selecting locomotives ................................................................... 15

8.1 Selecting a locomotive address from the stack ..................... 15

8.2 Entering a new locomotive address into the stack ................ 16

8.3 Deleting a locomotive address from the stack....................... 18

9Locomotive functions .................................................................... 19

9.1 Switching locomotive functions with function keys ................ 19

9.2 Switching locomotive functions with the rotary knob ............. 20

9.3 Assigning locomotive functions to function keys ................... 21

9.4 Setting a locomotive function to permanent or temporary

operation ................................................................................ 22

9.5 Assigning function acronyms to locomotive functions ........... 24

9.6 Deleting a function acronym .................................................. 26

9.7 Changing a function acronym................................................ 27

9.8 Deleting all function acronyms............................................... 28

10 Double traction (Double Header).................................................. 29

10.1 Requirements to assemble a double traction ........................ 29

10.2 Assembling two locomotives in a double traction.................. 29

10.3 Deleting a double traction...................................................... 31

10.4 Error messages during double tractions................................ 32

11 Switching points and signals......................................................... 33

12 Setting (programming) locomotive decoders (PoM)..................... 34

12.1 Reading CVs via PoM and the address display LRC120...... 36

13 System settings............................................................................. 38

13.1 Setting and reading a locomotive address on the

programming track................................................................. 40

13.2 Setting and reading the XpressNet address.......................... 44

13.3 Setting the language.............................................................. 46

13.4 Resetting the LH01 ................................................................ 47

13.5 Resetting command stations (LZV100/LZ100)...................... 48

13.6 Displaying the version number of the LH01 .......................... 49

13.7 Displaying the version number of the command station........ 50

13.8 Setting the club mode ............................................................ 51

13.9 Displaying the hardware ID ................................................... 54

13.10Setting the brightness of the display...................................... 55

13.11Enabling/Disabling the displaying of function acronyms ....... 56

14 Technical appendix....................................................................... 57

14.1 Help in case of malfunction.................................................... 57

14.2 List of error messages ........................................................... 58

14.3 Display text / Languages ....................................................... 59

4 Information LH01

1 Welcome!

We would like to congratulate you on your acquisition of the LH01 by

Digital plus by Lenz®. We hope you will enjoy this model railway

control.

The purpose of this operating manual is to explain the use of the

LH01. If you still have questions after reading this manual, please

ways of contacting Lenz Elektronik GmbH:

Mail address:

Lenz Elektronik GmbH

Vogelsang 14

D-35398 Giessen

Phone:

+49 (0) 6403 900 133

A recorded message will

inform you of our

availability.

Fax:

+49 (0) 6403 900 155

E-mail:

[email protected]

If you encounter any problems with the LH01, please contact us,

providing a problem description as well as the following information:

Version number of the command station

Version number of the LH01

Designation, version number and service number of all connected

XpressNet devices (additional manual controls, Interface etc.).

This will help our service department solve the problem. Thank you.

1.1.1 All present?

Please check if all components have been delivered:

- LH01 device

- Connecting cable

- Operating manual (this booklet)

If any component is missing, please ask your specialist supplier for a

subsequent delivery.

2 Important advice, please read first!

The manual control LH01 is a component of the

Digital plus by Lenz

system and was submitted to intensive testing before delivery. Lenz

Elektronik GmbH guarantees fault-free operation if you follow the

advice below:

The LH01 may only be operated with

Digital plus by Lenz

system

components. Any use other than that described in this operating

manual is not permitted and all guarantees will be invalid if the LH01

is used inappropriately. Connect your LH01 only to devices that are

designated for such connection. This operating manual will tell you

which devices are suitable. Do not expose the LH01 to damp or direct

sunlight.

WARNING!

Do not leave your model railway system unsupervised

during operation! The heat generated by a short-

circuit creates a fire risk!

6 Information LH01

3 Overview of the features of the LH01

Locomotive

addresses

Locomotive addresses range from 1 - 9999.

Address 0 is used to control an analogue

locomotive.

Stack for

locomotive

addresses

The LH01 has a stack for locomotive addresses

that comprises 12 slots. The stack serves to

store the locomotive addresses as well as the

settings used most frequently.

Locomotive

functions and

configuration

Up to 29 functions are available for each

locomotive address.

Use of the LH01 with a command station LZV100

facilitates the independent setting of these 29

functions to permanent or temporary operation.

This setting is stored with the locomotive address

in the LZV100.

Permanent operation:

Press the key once to

enable this function and

again to disable this

function.

Temporary operation:

This function is enabled

as long as the

corresponding key is

pressed, and disabled

as soon as the key is

released.

Function

acronyms

You can assign an acronym to each of the 29

functions from among the list of acronyms

contained in the LH01. This facilitates finding a

desired function. You can enable and disable the

display of acronyms.

Speed steps

The LH01 supports 28 or 128 speed steps

depending on the mode set in the command

station for the respective locomotive address.

The mode cannot be changed.

Club mode

The LH01 has two so-called ‘club modes’in

which certain functions of the LH01 are disabled.

This allows operation by model railway fans who

are not fully familiar with the LH01.

Double traction

Two locomotives can be joined in a double

traction and controlled simultaneously.

Multiple traction

Multiple tractions that are already joined (by

means of the LH100 or LH90) can be controlled.

It is not possible to join a multiple traction with the

LH01.

Programming in

operational

mode (PoM)

PoM allows you to change the settings of the

locomotive that is currently being controlled. You

can change, for example, the starting delay,

maximum speed, or sound volume.

Changing a

locomotive

address

You can read or change a locomotive address on

the programming track of the LZV100.

Points, signals

and other

accessories

The address range for points, signals and other

accessories (for example, uncouplers) ranges

from 1 to 999.

XpressNet

Communication with the command station is

made through the XpressNet connection.

As is the case with all other XpressNet devices,

your LH01 can be disconnected and reconnected

during operation. The locomotive controlled last

will continue its operation with the last settings

stored. Once reconnected, this locomotive will

again be controlled.

Housing

Plastic

Dimensions

W 70 mm x H 125 mm x D 38 mm

8 Information LH01

Illustrations in the step-by-step instructions:

Key

Display

Explanation

In this booklet all entries in the LH01 are shown on the left.

All corresponding illustrations of the display after entry are

shown on the right.

All operating steps described in this booklet presume that the

LH01 is connected to the Digital plus by Lenz ®system and

that the system is turned on.

Illustration of displays and operating elements:

‘0001’'Esc'

The displays and operating elements of the LH01 are depicted

as illustrations. References to the display are indicated by

single quotes (‘’).

Cross references:

(p. 23)

This arrow refers to specific pages of the operating manual

that contain further information on a given subject.

Important information:

Text boxes contain important information or

advice.

4 Operating elements of the LH01

The rotary knob is

used to make

entries. Apart from

the rotary function,

the knob has five

key functions: up,

down, left, right,

and centre.

Function keys

A, B, and C:

For each locomotive

address in the stack,

locomotive functions

(F0 to F28) can be

assigned to these

keys.

Use the ‘Esc’ key to

go back one step in

the menu structure.

The LEDs

surrounding the

rotary knob indicate

when you are in one

of the menus.

10 Information LH01

5 Connection and initial operation

The LH01 can be used with the command stations LZ100 or LZV100.

The LH01 requires the software version 3.6 for the

command station LZ100/LZV100.

Update your command station, if necessary.

Insert the Western plug of the enclosed connecting cable

into the socket of the LH01.

Insert the five-pole DIN plug into the five-pole DIN socket

at the back of the LZ100/LZV100.

Altri manuali per digital plus lh01

Indice

Altri manuali Lenz Telecomando

Lenz

Lenz DIGITAL PLUS SET-02 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione

Lenz digital plus lh01 Manuale utente

Manuali Telecomando popolari di altre marche