Leuze electronic HT3CI Manuale utente

HT3CI

Label sensor

Leuze electronic GmbH + Co. KG

[email protected]

In der Braike 1 D-73277 Owen Tel.: +49 (0) 7021 573-0

We reserve the right to make changes – 2019/09/24 – 50142030

www.leuze.com•

1Figure part

Installation and setting

The details on installation and on label sensor setting take into account a typical

application for detecting the label on a transparent container, e.g., mineral water in

a glass or PET bottle with paper label.

– Having a particularly strong influence on the function are color and surface

structure of the container, container contents, the geometrical arrangement

of the label sensor (angle to the horizontal as well as distance between label

sensor and container) and especially the label.

– The label sensor evaluates signal differences between the bare container

surface and the label surface. As long as there are clear signal differences

between the container surface and the label surface, the label sensor func-

tions very robustly. A predominantly white paper label on a white PET milk

bottle can, under some circumstances, not be detected due to the low signal

difference.

In the event of operating problems, change just one parameter and then observe

the effect of the measure. Necessary changes could be:

– Adjust the sensitivity via operational control (multiturn potentiometer)

– Increase or decrease the angle to the horizontal

– Increase or reduce the distance between label sensor and container

Mounting instructions

ÄAlign the label sensor at an angle of approx. 15°…20° to horizontal.

ÄIf possible, use the BTU200M-D12 mounting system (part no. 50117255).

AHT3CI label sensor

BBTU200M-D12 mounting system

CRod ⌀12mm

DContainer

Adjustment and alignment

ÄPush the BTU200M-D12 mounting system (B) without label sensor onto the

rod (C). Lightly tighten both screws.

ÄIncline the mounting plate of the mounting system approx. 15°…20°.

ÄAlign the label sensor (A) so that the optical outlet falls centrally on the con-

tainer (D).

ÄSecurely tighten both screws on the mounting system.

ÄScrew down label sensor (A) to the mounting plate of the mounting system

(B).

ÄCheck clearance (approx. 35mm) and setting of the label sensor.

Setting the label sensor

AAligning the label sensor

The label sensor evaluates the signal difference between a free glass surface

(specular reflection) and a surface with a label (diffuse reflection). For optimum

adaptation to the conditions, the sensitivity of the label sensor can be adjusted via

the operational control.

Application (typical) Clear signal difference

between the free glass

surface and the label sur-

face, e.g., paper label

Small signal difference

between the free glass

surface and the label sur-

face, e.g., foil label.

Adjustment via opera-

tional control

Gently turn the operational control (multiturn poten-

tiometer) on the device until the yellow LED no longer

illuminates.

Observation After adjustment, the label sensor is in a stable OFF

state and shows no faulty switching on the bare glass

surface without label.

If the label is turned into the detection range of the la-

bel sensor, the label sensor detects the label over the

entire length of the label.

NOTICE

Procedure in the event of faulty switching on the glass surface!

ÄRepeat the adjustment.

ÄCheck whether a stable switching behavior is achieved with a

slightly changed inclination.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Leuze electronic Accessori

Leuze electronic

Leuze electronic LA-78M Manuale utente

Leuze electronic

Leuze electronic LES 36 Manuale utente

Leuze electronic

Leuze electronic LPS Manuale utente

Leuze electronic

Leuze electronic GS 754B Manuale utente

Leuze electronic

Leuze electronic HTU318-300 M12 Series Manuale utente

Leuze electronic

Leuze electronic DMU318 W Series Manuale utente

Leuze electronic

Leuze electronic DMU318 Series Manuale utente

Leuze electronic

Leuze electronic rotoScan ROD4plus Manuale elenco delle parti

Leuze electronic

Leuze electronic SRK 96 Manuale utente

Leuze electronic

Leuze electronic BPS 34 Manuale elenco delle parti

Leuze electronic

Leuze electronic LRS Manuale elenco delle parti

Leuze electronic

Leuze electronic GS 61 Manuale utente

Leuze electronic

Leuze electronic HTU418B Series Manuale utente

Leuze electronic

Leuze electronic HT25CL2 Manuale utente

Leuze electronic

Leuze electronic SLS 78/R Guida rapida

Leuze electronic

Leuze electronic MC3 Series Manuale utente

Leuze electronic

Leuze electronic KRTM 3B Series Manuale utente

Leuze electronic

Leuze electronic CML 730i Manuale utente

Leuze electronic

Leuze electronic LCS-1 Series Manuale utente

Leuze electronic

Leuze electronic Line Profile Sensor Manuale elenco delle parti

Leuze electronic

Leuze electronic MLD-M00a Manuale utente

Leuze electronic

Leuze electronic Set-AC Manuale utente

Leuze electronic

Leuze electronic RotoScan Series Manuale elenco delle parti

Leuze electronic

Leuze electronic MC3x Series Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente