LevelOne FEP-0931 Manuale utente
1
FEP-0931
User Manual
Brief introduction
Many thanks for purchasing Fast Ethernet POE Switch! This
product supports IEEE802.3U/100Base-Tx protocol, as well
as full duplex and half duplex mode. It provides 8 TX ports
and a UPLINK port, which can suit for most 10/100M
networks. This manual is for 100M converters. The
following purchasing guide is for your reference.
Purchasing guide for optical media converters
Model
Specifications
9 x UTP
10/100M adaptive, with 8 PSE ports
Packing list
Please check the following items in the package before
installing the converter.
FEP-0931 1 piece
AC/DC adapter 1 piece
User manual 1 copy
Please contact the dealer immediately for any missing or
damaged items.
Interface
RJ-45 interface
1. Interface
All RJ-45 copper interfaces support Auto-Negotiation
for optimal speed detection through RJ-45 CAT5 UTP cables
with a maximum length of 100 meters (or 328 feet). They
also support standard Auto-MDI/MDI-X that can detect the
type of connection to any Ethernet device without requiring
special straight or crossover cables.
2. Connection
Fig.1 Basic Network Connection
All ports support 802.3af compliant Power Devices (PD)
and other network devices (e.g. work station, hub or switch).
Connect one end of the standard UTP CAT5 network cable
to the 10/100Mbps RJ-45 ports on the front panel of the
switch. Connect the other of the cable to the typical network
devices.
Panel
1. Front
2. Back
2
Explanation for LED indicator lamp
The LED indicator lamps serve as device monitoring and
error display. The following explains each LED indicator.
LED
Status
Explanation
PWR
Green
Lit when Power is available.
POE
P1~P8
Yellow
Lit when the connected port(s) is/are PSE
starts to supply power
OFF
Off when the connected port(s) is/are PSE
stop power supply
L/A
P1~P9
Green
Lit when there is/are network device(s)
connect the corresponding port(s)
Blink
Blink when the corresponding ports is(are)
transmitting data flows
SPD
P9
Green
Data rate is 100Mbps
OFF
Data rate is 10Mbps
Two bits
DIP
switch
Auto-mode
Automatically adjust the network
transmission rate according to the length of
network cable.
10M
Forced downlink port rate is 10M，Support
250 meters long distance transmission
VLAN&
Auto-mode
Automatically adjust the network
transmission rate according to the length of
network cable. Support downlink port
isolation, only uplink port communication
VLAN&
10M
Forced downlink port rate is 10M,Support
downlink port isolation and 250 meters
long distance transmission, only uplink port
communication
Installation
1. Turn off the power of the device/station in the network in
which the converter will be installed.
2. Ensure that there is no activity in the network.
3. Attach a UTP cable from the 100Base-TX network to the
RJ-45 port on the converter.
4. Connect the power cord to the converter.
5. Turn on the power of the converter and check that the
Power LED lights up. The TP Link will light when all the
cable connections are satisfactory.
6. When the P1~P9 LINK/ACT LED is green, the
corresponding port is running under 10/100Mbps.
Technical parameters:
1. Standard Protocol:
IEEE 802.3 10 Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x flow control
IEEE 802.3af POE
IEEE 802.3at POE+
2. Connectors:
8×UTP RJ-45 connector with PSE function
1×UTP RJ-45 connector
3. Operation mode:
TX: 10/100 Mbps auto-negotiation mode
4. Power supply:
5. PSE Pinout: PIN1/2: Pos(+), PIN3/6:Neg(-)
6. Operation temperature: -20℃~70 ℃
7. Storage temperature: -20℃~70 ℃
8. Operation humidity: 5%-90% non-condense
9. Storage humidity: 5%-90% non-condense
10. Twisted Pair cable: Cat5 UTP cable
11. Dimensions: 30×170.5×80.5mm (H x W x D)
Note:
Uplink port supports automatic detection of network
cable length to adjust network transmission rate.
Warning:
1. This product is suitable for indoor application.
2. The appliance inlet is used as the disconnect device and
shall remain readily operable at all time.
Trouble shooting:
1. Device is not connecting. Please check that the
corresponding network device is using the same transfer rate
as the media converter (10Mbps or 100Mbps).
Altri manuali per FEP-0931
1
Altri manuali LevelOne Interruttore
LevelOne
LevelOne GEP-2651 Manuale utente
LevelOne
LevelOne OfficeCon GSW-0841 Manuale utente
LevelOne
LevelOne Infinity IES-1080 Manuale utente
LevelOne
LevelOne GEL-5261 Manuale utente
LevelOne
LevelOne 20 GE PoE-Plus Manuale utente
LevelOne
LevelOne GEL-2870 Manuale di programmazione
LevelOne
LevelOne INFINITY IES-0520 Manuale utente
LevelOne
LevelOne IGP-1061 Manuale utente
LevelOne
LevelOne 55051007 Manuale utente
LevelOne
LevelOne GEP-0523 Manuale utente
LevelOne
LevelOne FEP-0812v4 Manuale utente
LevelOne
LevelOne FEP-0840 Manuale utente
LevelOne
LevelOne ViewCon KVM-0850 Manuale utente
LevelOne
LevelOne FEU-0812 Manuale utente
LevelOne
LevelOne FSW-0507TX Manuale utente
LevelOne
LevelOne GTP-2881 Manuale utente
LevelOne
LevelOne KVM-0211 Manuale utente
LevelOne
LevelOne FSW-2106 Manuale utente
LevelOne
LevelOne GSW-2470TGX Manuale utente
LevelOne
LevelOne GSW-1657 Manuale utente
