LevelOne GSW-2692 Manuale utente

LevelOne

GSW-2692

24-Port 10/100M + 2G Combo

L2 Stackable Switch

Installation Guide

Version 1.0-0608

Compliances and Safety Warnings

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause interference to

radio communications. It has been tested and found to comply with the limits for a Class A

computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to

provide reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference, in which case the user, at his own expense, will be required to take whatever

measures may be required to correct the interference. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance could void

your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better

for 10 Mbps connections, Category 5 or better for 100 Mbps connections, Category 5, 5e,

or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/

125 micron multimode fiber or 9/125 micron single-mode fiber.

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this

device.

RFI Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electricalfasttransient/burstaccordingtoEN 61000-4-4:1995(AC/DCpower

supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993

(1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD: • EN 60950-1:2001

iii

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Please read the following safety information carefully before

installing the switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel

only.

• The unit must be connected to an earthed (grounded) outlet to comply with international

safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove

power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected

also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT†supplies. If your supplies are of IT type, this unit

must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the

secondary connection point labelled Neutral, connected directly to earth (ground).

When using a fiber optic port, never look at the transmit laser while it is

powered on. Also, never look directly at the fiber TX port and fiber cable

ends when they are powered on.

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß

und auf die Faserkabelenden schauen, während diese

eingeschaltet sind.

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

•

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA

5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard

DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted

with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Warnings and Cautionary Messages

Environmental Statement

The manufacturer of this product endeavours to sustain an environmentally-friendly policy

throughout the entire production process. This is achieved though the following means:

• Adherence to national legislation and regulations on environmental production

standards.

• Conservation of operational resources.

• Waste reduction and safe disposal of all harmful un-recyclable by-products.

• Recycling of all reusable waste content.

• Design of products to maximize recyclables at the end of the product’s life span.

• Continual monitoring of safety standards.

End of Product Life Span

This product is manufactured in such a way as to allow for the recovery and disposal of all

included electrical components once the product has reached the end of its life.

Manufacturing Materials

There are no hazardous nor ozone-depleting materials in this product.

Warning: This product does not contain any serviceable user parts.

Warning: Installation and removal of the unit must be carried out by qualified

personnel only.

Warning: When connecting this device to a power outlet, connect the field ground lead

on the tri-pole power plug to a valid earth ground line to prevent electrical

hazards.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers

are compliant with the requirements of a Class 1 Laser Product and are

inherently eye safe in normal operation. However, you should never look

directly at a transmit port when it is powered on.

Caution: Wear an anti-static wrist strap or take other suitable measures to prevent

electrostatic discharge when handling this equipment.

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this

device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC

standards.

Documentation

All printed documentation for this product uses biodegradable paper that originates from

sustained and managed forests. The inks used in the printing process are non-toxic.

Purpose

This guide details the hardware features of the switch, including Its physical and

performance-related characteristics, and how to install the switch.

Audience

This guide is for system administrators with a working knowledge of network

management. You should be familiar with switching and networking concepts.

Related Publications

The following publication gives specific information on how to operate and use the

management functions of the switch:

The Stackable Fast Ethernet Switch Management Guide

Also, as part of the switch’s firmware, there is an online web-based help that describes all

management related features.

vii

Contents

Chapter 1: Introduction 1-1

Overview 1-1

Switch Architecture 1-2

Network Management Options 1-2

Description of Hardware 1-2

10BASE-T/100BASE-TX Ports 1-2

1000BASE-T/SFP Ports 1-3

Stacking Ports 1-3

Port and System Status LEDs 1-4

Power Supply Receptacles 1-6

Features and Benefits 1-6

Connectivity 1-6

Expandability 1-7

Performance 1-7

Management 1-7

Chapter 2: Network Planning 2-1

Introduction to Switching 2-1

Application Examples 2-2

Collapsed Backbone 2-2

Network Aggregation Plan 2-3

Remote Connections with Fiber Cable 2-4

Making VLAN Connections 2-5

Application Notes 2-6

Chapter 3: Installing the Switch 3-1

Selecting a Site 3-1

Ethernet Cabling 3-1

Equipment Checklist 3-2

Package Contents 3-2

Optional Rack-Mounting Equipment 3-2

Mounting 3-3

Rack Mounting 3-3

Desktop or Shelf Mounting 3-5

Installing an Optional SFP Transceiver 3-6

Connecting Switches in a Stack 3-6

Connecting to a Power Source 3-8

Connecting to the Console Port 3-8

Wiring Map for Serial Cable 3-9

viii

Contents

Chapter 4: Making Network Connections 4-1

Connecting Network Devices 4-1

Twisted-Pair Devices 4-1

Cabling Guidelines 4-1

Connecting to PCs, Servers, Hubs and Switches 4-2

Network Wiring Connections 4-2

Fiber Optic SFP Devices 4-4

Connectivity Rules 4-5

1000BASE-T Cable Requirements 4-5

1000 Mbps Gigabit Ethernet Collision Domain 4-5

100 Mbps Fast Ethernet Collision Domain 4-6

10 Mbps Ethernet Collision Domain 4-6

Cable Labeling and Connection Records 4-6

Appendix A: Troubleshooting A-1

Diagnosing Switch Indicators A-1

Diagnosing Power Problems with the LEDs A-1

Power and Cooling Problems A-2

Installation A-2

In-Band Access A-2

Stack Troubleshooting A-2

Appendix B: Cables B-1

Twisted-Pair Cable and Pin Assignments B-1

10BASE-T/100BASE-TX Pin Assignments B-1

Straight-Through Wiring B-2

Crossover Wiring B-2

1000BASE-T Pin Assignments B-3

Fiber Standards B-4

Appendix C: Specifications C-1

Switch Features C-2

Management Features C-2

Standards C-3

Compliances C-3

Glossary

Index

Indice

Altri manuali LevelOne Interruttore

LevelOne

LevelOne KVM-0830 Manuale utente

LevelOne

LevelOne GEP-0823 Manuale utente

LevelOne

LevelOne FSW-0513 Manuale utente

LevelOne

LevelOne GSW-0503T Manuale utente

LevelOne

LevelOne GTL-2661 Manuale utente

LevelOne

LevelOne IGP-0432 Manuale utente

LevelOne

LevelOne Infinity IES-1611 Manuale utente

LevelOne

LevelOne KVM-0290 Manuale utente

LevelOne

LevelOne OfficeCon FSW-2420TX Manuale utente

LevelOne

LevelOne GSW-1675T Manuale utente

LevelOne

LevelOne FSW-2470 Manuale utente

LevelOne

LevelOne GTL-2880 Manuale utente

LevelOne

LevelOne GEP-2651 Manuale utente

LevelOne

LevelOne GEP-2652 Manuale utente

LevelOne

LevelOne IES-0840 Manuale utente

LevelOne

LevelOne GSW-1657 Manuale utente

LevelOne

LevelOne IGP-1271 Manuale dell'operatore

LevelOne

LevelOne GEL-2460 Manuale utente

LevelOne

LevelOne GSW-1676 Manuale utente

LevelOne

LevelOne IES-0883 Manuale utente

LevelOne

LevelOne GSW-2473 Manuale utente

LevelOne

LevelOne GTL-2690 Manuale utente

LevelOne

LevelOne GSW-5270 Manuale utente

LevelOne

LevelOne GTL-2880 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente