Leviton POENS-8PT Manuale utente
PoE
Link/ACT
PoE 1X PoE 2X PoE 3X PoE 4X PoE 5X PoE 6X PoE 7X PoE 8X
8-Port 10/100 Mbps
Ethernet PoE Switch
IEEE802.3af 15.4W
8-Port PoE Network Switch
Cat. No. POENS-8PT
User’s Guide
DI-000-POENS-05D-W
WEB VERSION
WARNINGS AND CAUTIONS
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never push objects
of any kind into this product through openings, as they may touch dangerous voltages.
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never touch
uninsulated wires or terminals unless the wiring has been disconnected at the network
interface.
• Read and understand all instructions. Follow all warnings and instructions marked on
the product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or
laundry tub, in a wet basement, or near a swimming pool.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the components are
designed specifically for use in wet locations.
• Use caution when installing or modifying communications wiring or components.
• Use only the supplied AC adapter. The use of any incompatible adapter may cause
damage to the equipment and void the warranty.
• For indoor use only.
• SAVE THESE INSTRUCTIONS.
For Technical Assistance Call: 800-824-3005 - www.leviton.com Page 3
WEB VERSION
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC COMPLIANCE
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Page 4
WEB VERSION
Table of Contents
Introduction …………………………………………………………………… page 6
Power Over Ethernet (PoE) ……………………………………..…………… page 7
Installation …………………………..………………………………………… page 8
Connecting Network Cables ………………………………………………… page 9
Front Panel ……….………………………………………………………… page 10
Front Panel LED Indicators .………………………………………………. page 11
Rear Panel ……………………………..…………………………………….. page 12
Technical Specifications ……..…………………………...……………… page 13
Page 5
WEB VERSION
INTRODUCTION
The POENS-8PT combines a small, high efficiency 8-Port 10/100Mbps Ethernet switch
with IEEE 802.3af Power over Ethernet (PoE) capability on all 8 ports. It can be used to
provide power to up to 7 Leviton®OmniTouch™ 7 touchscreens
(one port must be connected to the network).
The POENS-8PT is a Power Source Equipment (PSE) device that is fully compatible with
Powered Devices (PD) that comply with the IEEE 802.3af standard. The PoE ports on the
POENS-8PT can also be used to power other Powered Devices (PD), such as the Leviton
BitWise™ BC4, Leviton Door Station, Leviton PoE IP cameras, PoE Wireless Access
Points, PoE Printer, etc., without requiring additional power on the network. Each of the
PoE ports can provide 15.4 Watts of power as well as 10/100M data transmission through
the traditional UTP cable to the Powered Device.
The POENS-8PT is supplied with an external 48 VDC power adapter. No configuration
is required and installation is quick and easy. Support for automatic MDI / MDI-X on all
of the ports eliminates the need for a crossover connection to another switch or hub.
Auto-negotiation on each port senses the link speed (100 Mbps or 10 Mbps) of a network
device and intelligently adjusts for compatibility and optimal performance.
NOTE: This device is designed for indoor use. Do not use outdoors.
Page 6
WEB VERSION
POWER OVER ETHERNET (PoE)
Power Over Ethernet (PoE):
Power over Ethernet (PoE) integrates 48V power and data onto one single cable,
eliminating the need to have power available at the equipment locations. Power and data
are integrated onto the same cable, up to 100 meters (328 feet).
Features:
• 8 x 10/100Mbps Auto-negotiation Ethernet RJ-45 ports with PoE on all 8 ports.
• Compliant with IEEE 802.3af specification.
• Supports PoE power up to 112 W total, for all PoE ports.
• Supports PoE IEEE 802.3af compliant Powered Device (PD).
• Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
• Full/half duplex transfer mode for each port.
• Wire speed reception and transmission.
• Up to 1000 unicast address entities per device, self-learning, and table aging.
• 64K Byte packet buffer.
Page 7
WEB VERSION
INSTALLATION
Unpacking:
Open the shipping carton of the POENS-8PT and carefully unpack its contents:
• POENS-8PT (8-Port PoE Network Switch)
• AC Power adapter
• User’s Guide
Installation:
• The surface must support at least 4.4 lb and a power outlet should be within 5 feet of
the switch.
• Visually inspect the DC power jack and make sure that is fully secured to the power
adapter.
• Make sure that there is proper heat dissipation from and adequate ventilation around
the switch.
NOTE: DO NOT place heavy objects on the switch.
Page 8
WEB VERSION
CONNECTING NETWORK CABLES
Connecting Network Cables:
The POENS-8PT has 8 10/100Mbps Ethernet ports. Each port incorporates 10/100Mbps
support using traditional UTP cables. Each of the 8 PoE ports will automatically activate
when a compatible device is identified. The POENS-8PT will supply power through the
port to the connected PoE device (PD).
Legacy devices that are not compatible will not be supplied power. This feature allows
users to freely and safely mix legacy and PoE compatible devices connected to switch.
This Switch supports 10Mbps Ethernet or 100Mbps Ethernet and runs both in half and
full duplex mode using two pairs in the cable.
All ports are automatic MDI ports. The switch can auto negotiate to MDI or MDI-X, so
you can connect either a standard network or crossover cable.
When connecting an OmniTouch 7 touchscreen to the network, a UTP Cat-5/5e
(4-pair) cable is required for operation. Run the cable between the location of the
POENS-8PT and the location of the OmniTouch 7 touchscreen.
Page 9
WEB VERSION
FRONT PANEL
There is an LED power indicator and 8 RJ-45 ports with LED status indicators on the front
panel of the POENS-8PT. The LED status indicators provide status for each of the ports.
Ports:
PoE Ports: PoE1X to PoE8X
• All ports are 10/100Mbps 802.3af PoE enabled ports.
• All ports will automatically activate when a compatible PoE device is identified. The
POENS-8PT will supply power through the Ethernet port to the connected PoE device
(PD).
• The POENS-8PT also supports legacy devices that are not PoE compatible. In this
case, the PoE ports will not supply power to those devices. This feature allows users
to freely and safely connect legacy and PoE compatible devices to the switch.
These RJ-45 ports are Auto-MDI ports. This switch can auto negotiate to MDI or MDI-X,
so you can connect the RJ-45 cable regardless of whether it is a standard network or
crossover cable.
PoE
Link/ACT
PoE 1X PoE 2X PoE 3X PoE 4X PoE 5X PoE 6X PoE 7X PoE 8X
8-Port 10/100 Mbps
Ethernet PoE Switch
IEEE802.3af 15.4W
Page 10
WEB VERSION
FRONT PANEL LED INDICATORS
The LED status indicators provide status for each of the ports and can be used for
monitoring and troubleshooting when required.
PoE
Link/ACT
PoE 1X PoE 2X PoE 3X PoE 4X PoE 5X PoE 6X PoE 7X PoE 8X
8-Port 10/100 Mbps
Ethernet PoE Switch
IEEE802.3af 15.4W
Power LED
LED on: Power On; LED off: Power off
LINK/ACT
LED on: this port is Linked and Active
LED off: this port is not Linked or inactive
PoE (1x to 8x)
LED on: A PoE Powered Device (PD) is connected and the port is
supplying power
LED off: A PoE Powered device (PD) is not connected; the port is
not supplying power
Page 11
WEB VERSION
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Leviton Interruttore
Leviton
Leviton RZS15-1L Manuale utente
Leviton
Leviton 1755 Manuale utente
Leviton
Leviton DT115 Manuale utente
Leviton
Leviton Vizia-RF Istruzioni per l'installazione
Leviton
Leviton powerswitch MDS3 Manuale utente
Leviton
Leviton 5655 Manuale utente
Leviton
Leviton SS0AV-091 Manuale utente
Leviton
Leviton 5-Port Gigabit Manuale utente
Leviton
Leviton Decora 6696 Manuale utente
Leviton
Leviton 1221-2KL Manuale utente
Leviton
Leviton Decora Plus 56021 Manuale utente
Leviton
Leviton 1463 Manuale utente
Leviton
Leviton HCS08 Manuale utente
Leviton
Leviton 1080 Manuale di istruzioni
Leviton
Leviton 91A00-1 Manuale utente
Leviton
Leviton Lumina ZS10S Manuale utente
Leviton
Leviton 2653 Manuale utente
Leviton
Leviton decora plus 56021 Manuale utente
Leviton
Leviton powerswitch MDS3-AC Manuale utente
Leviton
Leviton HCS10 Manuale utente
