LG SuperSign Elite-c Manuale utente
ENGENGLISH
Please read the safety information carefully before using the product.
SuperSign Elite-c
Owner's Manual
www.lgsupersign.com
ENG
ENGLISH
2Before You Begin
What is SuperSign Elite-c Software?
SuperSign Elite-c is a remote management software solution for digital signage monitors de-
veloped based on LG Electronics' proprietary technology. SuperSign Elite-c helps you easily
control the settings (e.g., screen settings, power on/off) of the monitors connected to a network
or serial ports.
Signage Monitor
LG Signage monitors can be controlled through a LAN connection or RS-232C serial ports.
For a complete listing of signature monitor models supported by the SuperSign Elite-c soft-
ware, see the [Help] > [Information] menu in the software.
yAdditional monitor models may be supported by SuperSign Elite-c software in the fu-
ture. Please make sure to add your correct monitor model. If you add a wrong monitor
model, it may cause the software to malfunction.
NOTE
ENGENGLISH
3
Before You Begin
System Requirements
Hardware
CPU: Intel Pentium 4 1.8GHz or higher is recommended
RAM: 1GB or greater
Disk: 400MB or greater
Software
Net Framework 2.0 required
System
Windows Platform
For Windows 2000, Service Pack 4 or higher
For Windows 2003, Service Pack 1 or higher
For Windows XP, Service Pack 2 or higher
For Windows XP, Professional or higher
For Windows 7, Professional or higher
Features
Integrated Management through LAN and Serial Connection
yProvides easy management of monitors connected to LAN or serial connection.
Wide Area Network (WAN) Control
yAllows you to manage the monitors even at remote sites through WAN such as Inter-
net.
Automatic Search for Monitors on the Same Network
yAutomatically searches, adds, and manages the monitors connected to the same
network as the computer where SuperSign Elite-c installed.
Power on/off Scheduling and Input Signal Settings
ySets the monitor to be turned on/off the automatically and sets an input signal to be
applied when the monitor is turned on.
Easy Tile Mode
yAllows you to set the tile mode with the easy-to-use and intuitive GUI design.
Firmware Upgrade over LAN (S7 Platform or More)
yUpdates the monitor firmware easily via network.
Instant Messaging (S7 Platform or More)
yAllows you to display a message you want on the screen.
ENG
ENGLISH
4Installation
SuperSign Elite-c Setup
Setting up SuperSign Elite-c involves establishing connections between the LG Electron-
ics’ signage monitors and their management program, SuperSign Elite-c software. Super-
Sign Elite-c connection setup supports the following two methods:
yLocal Area Network (LAN) connection
yRS-232 serial communications
Connecting Monitors to LAN
This method connects monitors to a network using a switch or a hub. Connect the network
cable from the LAN to the Ethernet port on the signage monitor.
ENGENGLISH
5
Installation
Setting IP Address for Network Monitor
Once the network cable is connected, set an IP address of the signage monitor to com-
plete the network connection. Follow the steps below to set the IP address of the monitor:
1Open the [Menu] window on the monitor.
2Select [Network] on the menu.
3Select [Network Setting] in [Network].
4Select IP setting mode in [IP Mode].
Case 1) IP Auto Setting
a. Click [Setting] to assign an IP address
automatically.
b. When IP setting is complete, click [EXIT] to exit the IP setting.
Case 2) IP Manual Setting
a. Assign an IP address, subnet mask, gateway, and DNS server address.
b. Click [Setting] to apply the IP setting.
c. When IP setting is complete, click [EXIT] to exit the IP setting.
5On the [Option] window, select [Product/Service Info] and then check whether the
IP address is properly assigned.
yA Local Area Network (LAN) is a network of computers in a short-range area such as
home, office and school.
NOTE
Example:
[Option]
window
Move OK
NETWORK
ꔋ
• Player Name
• Network Setting : Wired
• Network Status : Not connected
• Server IP Setting
• Server IP Status : Not connected
ENG
ENGLISH
6Installation
Connecting Monitors to RS-232C Serial Ports
For RS-232C serial port communication, use a RS-232C cable to connect a monitor directly to
the PC where SuperSign Elite-c software installed. To connect more than one monitor to the
computer, connect the first monitor to the computer with a RS-232C cable and then connect the
rest with a RS-232C cable as shown below.
yUp to 225 monitors can be connected using RS-232C serial cables.
CAUTION
Example: RS-232C connection
RS-232C Cable
(not included)
Monitor 1 Monitor 2 Monitor 225
Communication Parameter
yBaud Rate : 9600 buad Rate (UART)
yData Length : 8 bit
yParity Bit : None
yStop Bit : 1bit
yFlow Control : None
yCommunication Code : ASCII code
yUse a crossed (reverse) cable
yRS-232C cables need to be purchased separately.
ySee the pictures above for the configuration of RS-232C cables that can be connected to
the LG Signage products.
yWhen using 3-wire connections (non-standard), an IR daisy chain cannot be used.
RS-232C Configurations
RXD
TXD
GND
DTR
DSR
RTS
CTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
TXD
RXD
GND
DSR
DTR
CTS
RTS
TXD
RXD
GND
DSR
DTR
CTS
RTS
PC Set PC Set
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9 D-Sub 9
(Female) (Female)
D-Sub 9 D-Sub 9
(Female) (Female)
2
3
5
4
6
7
8
3
2
5
6
4
7
8
7-Wire Configurations (Standard RS-232C cable) 3-Wire Configurations (Not Standard)
NOTE
ENGENGLISH
7
Installation
SuperSign Elite-c Installation
Install SuperSign Elite-c software on the PC which will be connected to the signage moni-
tors through a network or serial cable. You can control signage monitors using SuperSign
Elite-c installed on the PC.
Installing SuperSign Elite-c
This section describes the procedure for installing SuperSign Elite-c on the PC.
1Insert the SuperSign Elite-c installation CD provided with the product into the CD-
ROM drive.
2Run Setup.msi in the ‘SuperSign Elite-c’ folder of the CD.
3When the Setup Wizard window appears, click [Next].
yWhen the popup below appears while running setup.msi, install .NET Framework 2.0 first
by referring to the “Installing .NET Framework 2.0” section. Then, continue to install the
SuperSign Elite-c software.
NOTE
ENG
ENGLISH
8Installation
Removing SuperSign Elite-c
This section describes the procedure for removing SuperSign Elite-c from the PC.
Select Start > Settings > Control Panel > Add/Remove Programs > SuperSignElite-c x.x to
remove the software.
4After selecting an installation folder and a user, click [Next]. Click the [Browse…]
button to change the default installation folder.
5Click the [Next] button to start the program installation.
6When the installation is complete, click the [Close] button.
ENGENGLISH
9
Installation
Installing .NET Framework 2.0
1Download .NET Framework 2.0 from the following site, and run it.
http://www.microsoft.com/en-us/download/details.aspx?id=1639
2After agreeing to the terms, click the [Install] button.
3When the installation is complete, click the [Exit]
button.
ENG
ENGLISH
10 SuperSign Elite-c
Touring the Software
SuperSign Elite-c program provides remote controlling of digital signage monitors through
a network or serial connection.
Start screen
In the Figure Item Description
A Menu Provides the menu for general functions.
BMonitor
viewer
Provides management functions for the registered
signage monitors.
CControl tabs Provides control functions for the selected monitor.
D Control panel Provides the information and configures settings for
the selected function in the one of the control tabs.
Item Description
File Allows you to exit the program.
Group Allows you to create, open, modify, save, and remove signage monitor
groups.
Monitor Allows you to add and remove the monitors connected through serial
cable or network.
Setup Allows you to set language, change login password, and set up
schedule.
View Allows you to view the log.
Help Allows you to check the SuperSign Elite-c version and supported
signage monitor models.
Menu
Provides the general functions used on SuperSign Elite-c.
A
BC
D
Indice
Altri manuali LG Software
Manuali Software popolari di altre marche
PS Audio
PS Audio PowerPlay Manuale del proprietario
Brady
Brady LOCKOUT PRO 3.0 Manuale di servizio
Avaya
Avaya Interaction Center Manuale utente
Texas Instruments
Texas Instruments TI-83 Plus Silver Edition Manuale
Novell
Novell GROUPWISE 8 - INTERNET AGENT Manuale utente
Oracle
Oracle Application 9i Manuale utente
Acer
Acer RDM Manuale utente
Canon
Canon Vixia HF21 Manuale utente
Canon
Canon ZR950 Manuale utente
Samsung
Samsung Auto Backup Manuale utente
Polycom
Polycom Vortex EF2201 Istruzioni per l'installazione e il funzionamento
Brocade Communications Systems
Brocade Communications Systems Brocade 8/12c Manuale utente