Lindsay GrowSmart Multi-Control Manuale utente

Multi-Control

Operation Manual

P/N 1604010 Rev D (ECN 35207)

GS-1 Standard Controls

General Safety Instructions

General Safety Instructions for Controls

WARNING

Personal Safety: Through out this manual and on all safety signs, the precautionary statements

(“DANGER”, “WARNING”, “CAUTION” and “NOTICE”) can be found, followed by a hazard description

and preventative actions to be taken. These precautions are intended for the personal safety of the operator and

those within the vicinity of the machinery. Please take time to read these precautions.

Hazard Severity Panels

Background

Color of

Panel

Contrast

Color

Meaning/Use Hazard Severity Panel Illustration

Red White Indicates a hazardous situation, that, if not

avoided, will result in death or serious injury.

Orange Black Indicates a hazardous situation, that, if not

avoided, could result in death or serious injury.

Yellow Black Indicates a hazardous situation, that, if not

avoided, could result in minor or moderate

injury.

Blue White Indicates information considered important, but

not hazard- related (e.g. messages relating to

property damage).

NOTICE

Machine Integrity: Additional precautionary statements (“ATTENTION” and “IMPORTANT”) are intended

for machine integrity and are followed by specic instructions.

ATTENTION: The word “ATTENTION” is used to warn the operator of potential machine damage if a certain pro-

cedure is not followed.

IMPORTANT: The word “IMPORTANT” is used to provide the reader with information necessary to prevent minor

machine damage if a certain procedure is not followed.

WARNING: All maintenance and service must be performed by a Lindsay Dealer.

GS-2 Standard Controls

General Safety Instructions

WARNING

Lock Out/Tag Out: Disconnect all sources of energy and lock out machine before doing any

maintenance or repairs to the machine. Proper Lock Out procedures will prevent the energy source from

starting the machine or allowing parts to move unexpectedly

as well as prevent the machinery from being accidentally

turned on or restarted. Shut off and Lock Out all sources of

potential or kinetic energy. These may include, but are not

limited to, electrical, mechanical or hydro energy sources.

Lock Out is a procedure used for placing an actual locking de-

vice on the power source, preventing unexpected start up or

accidental release of energy. Lock Out is the preferred method

of accident prevention.

Tag Out procedure is used when the power can not be discon-

nected. Tag Out’s do not shut down the power source, Tag

Out’s only provide a warning about the danger of activating the machine.

Never try to operate machinery that is locked out or tagged out. Never attempt to remove these locks or tags on

machinery. Doing so will result in injury to personnel working on the machine. Only the initiator of the Lock Out or

Tag Out procedure may remove locks and tags.

WARNING

Main Disconnect: The main power disconnect is located at the main service breaker or

generator. The disconnect at the panel is not the main disconnect. A fusible service disconnect device

must be placed previous to this panel with the fuses sized for the load being supplied and installed in

accordance to NEC codes.

It is important to understand the differences between the Pivot Enable switch (if installed), High Voltage On/Off

switch and the service breaker On/Off throw switch.

The power company service disconnect provides the ability to turn off or return full service to the equipment from

the power company service line. This switch must be turned off and locked out when performing maintenance and

repairs on the system.

The High Voltage On/Off provides the ability to turn off or return power to the equipment from the service discon-

nect. This switch must be turned off and locked out in conjunction with the service disconnect switch. The High

Voltage switch only disconnects the power in the control panel, as energy is still coming in from the main power

line.

The Pivot Enable switch (if installed) provides power to the system controls. When enabled, the entire system and

the controls will power up. When turned off, the controls and system will not be energized. However, there will be

power in the panel circuitry. The Pivot Enable switch is NOT a disconnect and should not be treated as such.

GS-3 Standard Controls

General Safety Instructions

WARNING

Training: All individuals involved in the installation, operation or maintenance of this equipment must

receive and understand training in the safe and proper methods of performing all duties assigned to them

at the time of the initial assignment and at least annually thereafter. Safety messages and appropriate

response procedures to emergencies or other situations which may arise should be fully understood.

WARNING

Follow Safety Instructions: Carefully

read all safety messages in this manual and safety

signs on the machinery. Keep safety signs in legible

condition. Replace any missing or damaged safety signs.

Learn how to operate the machine and controls properly. Do

not allow anyone to operate the machinery without proper

instructions.

Keep the machine in proper working condition. Only have the

machine serviced by a trained service technician on a routine basis. Unauthorized modications to the machine

may impair the function and/or safety and reduce the life of the machine.

CAUTION

Practice Safe Maintenance: Understand maintenance procedures before doing work.

Always follow proper Lock Out/Tag Out procedures before performing any maintenance.

Never lubricate or service machine while it is moving. Keep hands, feet and loose clothing from power-driven

parts. Disengage all power and operator controls to relieve pressure. Allow all heat-generating units to cool.

Keep all parts in good condition. Remove any build up of grease, oil and debris. Ensure that all parts have been

properly installed by a certied technician.

Tower alignment, pressure switch adjustment and tower control switch adjustment must be performed by a quali-

ed service technician.

WARNING

Electric Shock: Follow these precautions to prevent serious injury or death.

DO NOT allow moisture to enter the main panel. Moisture can allow voltage to conduct across surfaces, creating a

shock potential.

Dangerous voltage potential may be present at lightning arrester. Visually inspect arrester before each operation.

If lightning arrester shows signs of impairment, contact a Lindsay Dealer.

WARNING

Electrical Connections: Keep all sparks and ames away from battery, as gases given off by

electrolyte are explosive. Avoid sparks by connecting the ground cable last and disconnecting it rst.

CAUTION

Weather Conditions: Always be aware of weather conditions (extreme heat/cold, snow, rain,

sleet, heavy precipitation and high winds). Schedule work or maintenance only when the weather condi-

tions are mild and dress appropriately for the climate.

GS-4 Standard Controls

General Safety Instructions

CAUTION

Lightning Strikes: Do not attempt to access the system if lightning or thunder have been de-

tected in the area. Wait 30 minutes after the last sighting of lightning or sound of thunder before access-

ing the system.

WARNING

Inspecting the System Prior to Operation: Always inspect the system before

operation. If the system appears impaired, do not operate the machinery and contact a Lindsay Dealer.

CAUTION

Wear Proper PPE: Always wear appropriate (NFPA 70E and

OSHA Compliant) Personal Protective Equipment (PPE) for the task

being performed. At a MINIMUM, the following are required equipment:

Ear Protection:

Prolonged exposure to loud noise can cause impairment or loss of hearing.

Wear a suitable hearing protective device such as earmuffs or earplugs to pro-

tect against uncomfortably loud noises.

The A-weighted emission sound pressure level at the pivot point does not ex-

ceed 70 dB.

Eye Protection:

Sharp Objects, debris and explosions can cause severe eye damage or blind-

ness. Wear Safety Standard approved protection that fully shields the eyes.

Additionally, wear a clear plastic face shield that fully surrounds the face from

brow to chin and covers the entire width of the face.

Foot Protection:

Prevent damage from falling or dropped objects on the feet by wearing steel-

toe shoes/boots with metatarsal protection.

Head Protection:

Prevent damage from falling or dropped objects on the head by wearing a Class G Hard Hat for head protection.

Gloves

Prevent electrical shock hazards, cuts and burns to the hands by wearing protective rubber gloves-class 0 with

leather protector and cloth liner.

CAUTION

Proper Work Platform: Provide a good work/standing platform for personnel to access the

machine. Elevated platforms and ladders must have restraints or railings in place before climbing or

lifting.

CAUTION

Proper Area Lighting: The owner shall provide area lighting as may be required.

GS-5 Standard Controls

General Safety Instructions

WARNING

Repairing the System: In the event that the Zimmatic System needs to be repaired;

disconnect the power source, depressurize the system and contact the Lindsay Dealer.

Only a Lindsay Dealer should make necessary repairs to the system.

Ensure that only Genuine Lindsay Parts are used on the system.

WARNING

Overhead Maintenance: Overhead maintenance should be performed by a Lindsay Dealer.

Never attempt to climb on an irrigation machine for any reason.

WARNING

Lifting Components: Extreme care is needed for lifting components during installation/

assembly. Only a Lindsay Dealer using the proper lifting equipment may perform this task.

Use caution when lifting heavy objects. Components weighing in excess of 50 lbs. (22.7 kg.) must be lifted with

the assistance of another individual or mechanical lifting device.

Do not work or stand under system or components during assembly. Due to the weights involved, severe injury or

death can result if components should fall.

WARNING

Dismantling the System: If it is ever necessary to dismantle a Zimmatic System, extreme

care must be taken. As with installation and assembly, dismantling must only be performed by a Lindsay

Dealer.

WARNING

Impaired Safety Protection: Do not attempt to operate if protection may be impaired. If the

equipment appears to have been changed or operates abnormally, protective devices may be impaired.

Do not attempt to operate and have the equipment serviced by a Lindsay Dealer.

WARNING: Ensure that power is turned off/disconnected before removing any protective covers.

WARNING: Do not use this product in a manner not specied in this manual.

CAUTION

Prepare for Emergencies; Be prepared for any emergency that may occur. Keep emergency

numbers for doctors, hospital, ambulance service and re department near your telephone.

GS-6 Standard Controls

General Safety Instructions

Earth Ground Protective Earth Ground Frame or Chassis Ground

The following symbols indicate grounding connections that can be found on irrigation systems.

P/N 1604010 Rev D (ECN 35207) Multi-Control Operation Manual

Table of Contents

General Safety Instructions for Controls .............GS-1

Section 1- Specications and Compliance ............. 1-1

Requirements for Electrical Service ......................................................1-1

Compliance Standards.................................................... 1-1

Federal Communications Commission (FCC) Statement ....................1-1

Industry Canada Compliance Statement...............................................1-1

WEEE Statement......................................................................................1-1

Product Specications............................................................................1-2

Dimensional Data and Weight ................................................................1-3

Service .............................................................................. 1-4

Panels & Panel ID Locations........................................... 1-5

Micro-Controller Panel ............................................................................1-5

Expansion Panel ......................................................................................1-6

Wireless Switch .......................................................................................1-7

Section 2 - Operation ................................................ 2-1

Introduction to Multi-Control (MC) ................................. 2-1

Panel Controls.................................................................. 2-2

Section 3 - Service..................................................... 3-1

System Alerts ................................................................... 3-1

Seasonal Maintenance .................................................... 3-3

Start of Season ........................................................................................3-3

End of Season..........................................................................................3-3

P/N 1604010 Rev D (ECN 35207) Multi-Control Operation Manual

Table of Contents

Indice

Altri manuali Lindsay Sistema di irrigazione

Lindsay

Lindsay GROWSMART Manuale utente

Manuali Sistema di irrigazione popolari di altre marche

Hunter

Hunter Institutional Series Manuale utente

Cellfast

Cellfast 52-305 Manuale utente

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuale utente

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuale utente

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuale utente

Reliable

Reliable F1-300 Manuale utente

Tyco Fire Product

Tyco Fire Product Gem F892 Manuale utente

Netafim

Netafim NETBEAT Manuale utente

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuale utente

Tyco

Tyco CC3 Manuale utente

Reliable

Reliable F4FR Manuale utente

OpenSprinkler

OpenSprinkler OSPi Manuale utente

EINHELL

EINHELL GE-WW 5537 E Manuale utente

Valley

Valley Bender160 Manuale utente

Reliable

Reliable F1FR42 Series Manuale utente

Reliable

Reliable F1FR-300 Manuale utente

Toro

Toro 730 Series Guida rapida

Eden

Eden 97063-EDAMZ Manuale utente