INSTR,INST,DXS-10/EC
LINEAR P/N: 220134 A
MATERIAL: 20 LB. MEAD BOND
SIZE: 8.500" x 11.000"
INK: BLACK
SCALE: 1-1
DXS-10/EC
WIRELESS
KEYPAD
For Use With DVS-2400/EC
Security Console
Installation
Instructions
1. KEYPAD DETAIL 2. TYPICAL WIRELESS KEYPAD PLACEMENT
KEYPAD FOR
ENTERING YOUR
USER CODE
PRESS THE STAR
KEY TO RESET THE
KEYPAD IF YOU ENTER
THE WRONG CODE
MODE BUTTONS
FOR CHANGING
MODES
GREEN
OPERATION
LIGHT
EMERGENCY
BUTTON TO
SOUND SIREN
AT ANY TIME
FIRE BUTTON
TO SOUND
SIREN AT ANY
TIME
KEY TO ACTIVATE
HOME AUTOMATION
OUTPUT (A)
PRESS AND
HOLD FOR
2 SECONDS
TRANSMITTERS
BEDROOM
MAIN
CONSOLE
WIRELESS
KEYPAD
WINDOW
KITCHEN
FRONT
ROOM
FRONT
DOOR
3. OPENING KEYPAD 4. TABLE-TOP USE 5. WALL MOUNTING (INDOORS ONLY)
6. CLOSING KEYPAD 7. PROGRAM KEYPAD INTO CONSOLE INTERNATIONAL WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12)
months. The Warranty Expiration Date is labeled on the product. This warranty extends only to
wholesale customers who buy direct from Linear or through Linear’s normal distribution
channels. Linear does not warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or
liabilities on the part of Linear Corporation for consequential damages arising out of or in
connection with use or performance of this product or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the
product. This Linear Corporation Warranty is in lieu of all other warranties express or
implied. For warranty service on Linear equipment return product, at sender’s expense to:
Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong
Attention: Repairs Department
REPAIRS POLICY
Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged
by the effects of lightning, water, fire, or other abnormal happenings.
Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured
equipment at Linear’s discretion.
The customer is always responsible for shipping and handling charges to the repairs facility. Linear
will pay return shipping and handling charges on “in warranty” products shipped back to the
customer. The customer will be billed for the return shipping and handling charges on “out of
warranty” products.
There will be a 50% expedite fee for any express requests.
The International Sales Manager must be notified prior to the return of product to Linear. All
international returns must have an International Repair Authorization number (IRA#). The number
must be marked on all packages. Failure to do so will cause delays in processing.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable
wireless signaling. However, there are some limitations which must be observed. The radios are
required to comply with local rules and regulations as radio devices. As such, they have limited
transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void regulatory compliance. Infrequently used radio
links should be tested regularly to protect against undetected interference or fault. A general
knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2002 Linear Corporation 220134 A
USE THE FOUR SCRATCH
DETERRENT PADS PROVIDED
FOR TABLE-TOP USE
CONNECT BATTERY
TO BATTERY CLIP
FROM TOP OF CASE TWIST
SCREWDRIVER BETWEEN
CASE HALVES UNTIL IT
POPS OPEN
ATTACH REAR CASE TO WALL
WITH THE TWO SCREWS PROVIDED
MOUNT AT A CONVENIENT
LOCATION NEAR PRIMARY
ENTRY/EXIT DOOR
FIRST HOOK BOTTOM
EDGE TOGETHER
THEN, SNAP CASE SHUT
2
1
HOLD OFF BUTTON FOR
3 SECONDS WHEN FINISHED
TO EXIT LEARN MODE
PRESS STAR KEY
TO SEND SIGNAL
ENTER MASTER
USER CODE
PRESS
TEST
ENTER AN
UNUSED SENSOR
NUMBER
SEND SIGNAL
FROM KEYPAD
START IN
TEST MODE
TEST
R&TTE VAEE 27833, EMC, SFT, ETS
Linear Corporation declares that the
apparatus DXS-10/EC complies with the
essential requirements and other relevant
provisions of Directive 1995/5/EC
BY
(760) 438-7000 • FAX (760) 438-7043
www.linearcorp.com
