Link-m-technologies WILO 900 Manuale utente

WILO900 LOW RIDER REMOTE CONTROL SYSTEM

BY Link M Technologies

Owners Manual

Document 5.08.17-18

Revision 2.0

Introduction

Thank you for purchasing our product.

The WiLo 900 Low Rider Remote Control system was

designed with the input of low rider enthusiasts whose past

experiences with remote controls helped create a technical

wireless system into a simple form that will be a fun and

exciting addition to your pride and joy.

Link M Technologies

527 North Azusa Avenue #243

Covina, California 91722

http://www.linkmtechnologies.com

Table of Contents

CHAPTER 1..............................................1

GETTING STARTED ...................................1

CHAPTER 2..............................................2

SYSTEM OVERVIEW..................................2

Receiver Front Panel Controls.............2

Receiver Rear Panel.............................2

Interface Cable.....................................3

Transmitter Controls ............................4

CHAPTER 3..............................................5

INSTALLATION:QUICK .............................5

INSTALLATION:IN DEPTH.........................6

Suitable Location..................................6

Mounting ..............................................6

Connector Wiring List..........................7

Pump Example Wiring List...................8

Dump Example Wiring List ..................9

CHAPTER 4............................................10

SYSTEM OPERATION:QUICK ..................10

SYSTEM OPERATION:IN DEPTH..............11

Receiver Programming Setup.............11

Receiver Timing Setup........................11

Transmitter Operation........................12

Choreography Mode...........................12

Antenna Orientation...........................13

Transmitter Battery Replacement.......14

CHAPTER 5............................................15

TROUBLESHOOTING................................15

CHAPTER 6............................................16

SPECIFICATIONS .....................................16

LIMITED WARRANTY AND DISCLOSURE

STATEMENT............................................17

FCC NOTICE TO USER ............................18

INDEX.....................................................19

Getting Started

QuickreferencedwithIn Depth outlines.

his manual is outlined in two formats following the Overview section; “Quick” and

“In Depth”. The “Quick” format at the top of the chapter highlights the details of

the section for two purposes:

1. To provide the anxious user just enough information to get started right away

without having to glean the entire manual.

2. To refresh the memory of the one who has taken the time to read the entire manual.

The “In Depth” format provides all the operational details of the subject matter for the

enquiry minds as well as the product installers who need to know how the system

operates.

The System Overview section provides all the operating aspects of the transmitter and

receiver to briefly familiarize the user with the product.

Before You Begin

Parts Checklist

Make sure your package includes the following items:

1. WiLo 900TX handheld transmitter with antenna, batteries included.

2. WiLo 900RX receiver with right angle antenna.

3. 7’ Interface cable and assorted crimp terminals.

4. Two spare 3V size 2032 Lithium coin cell batteries.

5. Two spare mini blade 25 Amp fuses.

Chapter1

Chapter

System Overview

Receiver Front Panel Controls

Power

Push button On/Off switch lights up in center to indicate power.

Front

This variable timing control regulates how long the Front pump/s will stay ON minimizing over

extending the hydraulic cylinders. The pulse time can be adjusted from 35ms to 450ms.

Rear

Like the Front control, this variable timing control regulates how long the Rear pump/s will stay ON

minimizing over extending the hydraulic cylinders. The pulse time can be adjusted from 35ms to 450ms.

Program

Momentary push button switch used to “Learn” transmitter ID allowing system activation. See

Receiver Programming Setup for complete details.

Receiver Rear Panel

Fuses

Each solenoid control output is protected with a 25 Amp fuse that is shared between a respective

pump and dump pair.

Interface I/O connector

Output control signal and power input are provided via the interface connector.

Interface Cable

The Interface cables length is sufficient to mount the receiver in the trunk or on the rear

deck of the car.

Red 18AWG +12V input

Black 12AWG chassis GND

Red 10AWG +24V input

Brown Left Front Pump

Black Left Front Dump

Red Right Front Dump

Orange Right Front Pump

Yellow Left Rear Dump

Green Left Rear Pump

Violet Right Rear Pump

Blue Right Rear Dump

Figure 1: Interface cable length reduced for clarity.

Transmitter Controls

Function Switches

The transmitter has four 2 way Function switches labeled with the symbols; ♥♣♦♠.

Mode Switch

This slide switch on the bottom of the unit with the choice between “A” and “B”, changes

the action of the Function switches.

Power Switch

This switch is a momentary push button that turns the power ON to the unit as long as it is

held and is a safety feature to minimize accidental hydraulic activation.

Transmit LED

The LED below the antenna lights up when the Power switch is squeezed.

Chapter3

Installation: Quick

Someprideinworkmanship goes alongway for acleanandpresentable

installationto be proud of.

Important! Test your system before installation, then after installing the

Interface cable, then once more after connecting Interface cable to

WiLo900RX. Troubleshooting will be easier if a problem were to occur.

•Choose a suitable grounded location and mount the WiLo 900RX close

enough to the hydraulic control system so that the 7’ interface cable is

neatly routed between the two.

•Terminate the interface cable wires to power and the control solenoids

as illustrated in Figure 1.

•Plug the interface cable into the WiLo 900RX.

Power Program

Pumps

Pump Dump

Min Max Min Max

Los Controles

Pumpsolenoids

Dumpsolenoids

The receiver cable wiring

taps into the existing system at

the solenoid switches.

+24V

+12V

GND

Figure 2 Sample wiring diagram

Installation: In Depth

Therealnutsandbolts ofinstallations…

Suitable Location

The WiLo 900RX can be installed on the rear deck inside of the car or in the trunk, but

should be positioned such that:

•The interface cable neatly reaches the hydraulic control wiring or solenoids and

power source with enough slack left over to remove receiver should servicing be

needed.

•Mounting platform is grounded to vehicle chassis.

•The antenna is more than 6” horizontally from any metal such as batteries, pumps

and car chassis.

•The user can easily reach the unit to access controls.

Mounting

Always exercise caution and inspect underside trunk of a car checking for clearance to gas

tank and fuel lines before drilling holes and driving screws.

1. Mark the two mounting holes using the tabs as a guide.

2. Center punch and drill 1/8” holes on the vehicle chassis or a suitable grounded

platform.

3. Remove all metal shavings from holes before installing screws.

4. Position the receiver over the holes and drive one of the two supplied sheet metal

screws and washer to the right mounting tab (facing front).

5. Position interface cable Black ground wire over left mounting tab and drive second

screw and washer.

Connector Wiring List

Pin 12 Pin 3

Pin 10 Pin 1

The 12 pin male connector provides power to the receiver and output control signals to the

hydraulic control system via the 7’ interface cable.

Pin and Interface Cable wire list

Pin Wire color and function Pin Wire color and function

1 Red: Right Front Dump 7 Yellow: Left Rear Dump

2 Brown: Left Front Pump 8 Black 14AWG: Ground

3 Black: Left Front Dump 9 RED 10AWG: 24 Volt input

4 Orange: Right Front Pump 10 Green: Left Rear Pump

5 Red 18AWG: 12 Volt input 11 Blue: Right Rear Dump

6 RED 10AWG: 24 Volt input 12 Violet: Right Rear Pump

Note: Even though this system has been designed for a four pump four dump system,

controlling a single, double, or a three pump setup is just a matter of logical wiring.

See the Pump Example and Dump Example Wiring lists on the next two pages for various

single pump, two pump, and three pump wiring. These lists cover the basic and most

common setups because some systems are customized to the owners’ request.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente