Linksys PAP2 Manuale utente
Smart Member Services Linksys PAP2 Installation Guide
1 Adapter Description
The sections below briefly describe the PAP2 device.
1.1 PAP2 Overview
The PAP2 is a 2-port FXS phone adapter, which allows you to connect two (2) analog
phones.
PAP2 2-Port FXS Phone Adapter
1.2 Connectors and Pinouts
The image below displays the Ethernet (RJ-45) and analog (RJ-11) line pin-outs.
Ethernet (RJ-45) and Analog (RJ-11) Line Pin-Outs
1.3 Accessing the PAP2
1. Connect an analog phone to the RJ-45 connector on the PAP2.
2. Using the telephone keypad, press the star key (*) four (4) times: ****.
You will be prompted to enter a code.
3. Enter the appropriate code, followed by the pound (#) key. Refer to the PAP2
Menu Options table on the following page for codes.
PAP2 MENU OPTIONS
Action Code User Input Behavior Notes
Enter IVR Menu **** None Do not press any other keys
until you hear, “Configuration
menu. Please enter option
followed by the pound (#)
key, or hang up to exit.”
Check DHCP 100 None The system announces if
DHCP is enabled or disabled.
Set DHCP 101 Enter 1 to enable.
Enter 0 to disable. Enter the option, followed by
the pound (#) key.
Check IP
address 110 None
Set IP Address 111 Enter value using the
numbers on the
telephone keypad. Use
the star (*) key when
entering a decimal point.
Enter the value, followed by
the pound (#) key. DHCP
must be “Disabled,”
otherwise you will hear the
announcement, “Invalid
Option” if you try to set this
value.
Check Net Mask 120 None
Set Net Mask 121 Enter value using the
numbers on the
telephone keypad. Use
the star (*) key when
entering a decimal point.
Enter the value, followed by
the pound (#) key. DHCP
must be “Disabled,”
otherwise you will hear the
announcement, “Invalid
Option” if you try to set this
value.
Check Gateway 130 None
Set Gateway 131 Enter the value using the
numbers on the
telephone keypad. Use
the star (*) key when
entering a decimal point.
Enter the value, followed by
the pound (#) key. DHCP
must be “Disabled,”
otherwise you will hear the
announcement, “Invalid
Option” if you try to set this
value.
Check MAC
Address 140 None You will hear the phone
adapter’s MAC address.
Check Firmware
Version 150 None You will hear the phone
adapter’s firmware version.
Manual Reboot 7326668 None After you hear, “Option
successful,” hang up the
phone. The phone adapter
will automatically reboot.
PAP2 Menu Options
Smart Member Services Linksys PAP2 Installation Guide
2. Provisioning
2.1 General Configuration for Outbound Calling
To configure the PAP2 for outbound calling:
1. Connect to the PAP2 by entering the device’s IP address in the Web browser’s
Address bar. For instructions on obtaining the IP address, refer to section 2.3
Accessing the PAP2 on page 2 in this Guide.
2. Click on the Admin Login link in the upper right corner of the page, and then
click the advanced configuration link.
PAP2 Web Interface – Main Window
3. Click the System tab, and in the Internet Connection Type section, click the
DHCP drop-down menu, and select yes or no.
System Tab
4. If you set DHCP to no, enter the Static IP, NetMask, and Gateway information.
If you set DHCP to yes, continue to step 5.
5. Click the Submit All Changes button at the bottom of the page to save the
settings.
Smart Member Services Linksys PAP2 Installation Guide
2.2 Line-Specific Configuration
1. Click the Line1 or Line2 tab at the top of the page, and in the NAT Settings
section, change the following setting:
Field Value
NAT Keep Alive Enable no
2. In the Proxy and Registration section (see the screen on the following page),
change the following settings:
Field Value
Proxy byod1.net2phone.com
Use Outbound Proxy no
Use OB Proxy In Dialog no
Make Call Without Reg yes
Ans Call Without Reg yes
DNS SRV Auto Prefix no
3. In the Subscriber Information section (as shown in the Line1/2 Window screen on
the following page), enter a Display Name. This value can be any alphanumeric
string. Enter the following values for outbound only service:
Service Type Field Display Name
Value
Display Name (Line 1) NO_DID1
OUTBOUND SERVICE ONLY Display Name (Line 2) NO_DID2
4. Enter the User ID (account) and Password (PIN).
IMPORTANT You must have a different account and PIN for Line 1 and Line 2.
5. Click the Use Auth ID drop-down menu, and click no.
Smart Member Services Linksys PAP2 Installation Guide
Proxy and Registration and Subscriber Information Sections
6. Scroll to the Audio Configuration section (as shown in the Audio Configurations
and Dial Plan Sections screen on the following page), and change the following
settings:
Field Value
Preferred Codec G729a
Use Pref Codec Only no
G729a Enable yes
G723 Enable yes
G726-16 Enable no
G726-24 Enable no
G726-32 Enable no
G726-40 Enable no
DTMF Tx Method AVT
Smart Member Services Linksys PAP2 Installation Guide
Audio Configuration and Dial Plan Sections
7. In the Dial Plan section, change the Dial Plan to fit the dialing pattern in your
country. The dialed number must start with ‘1’ for US calls and ‘011’ for non-US
calls. Please read the PAP2 manual to customize your dial plan.
8. Click the Submit All Changes button to save the settings.
Smart Member Services Linksys PAP2 Installation Guide
Altri manuali per PAP2
14
Indice
Altri manuali Linksys Adattatore
Linksys
Linksys WUSB54GSC Manuale utente
Linksys
Linksys WPC54G EU Manuale utente
Linksys
Linksys WUSB54AG Manuale operativo
Linksys
Linksys WMP11 ver. 2.7 Istruzioni operative originali
Linksys
Linksys WAPPOE Manuale utente
Linksys
Linksys WPC54GX Manuale operativo
Linksys
Linksys PAP2 Manuale utente
Linksys
Linksys WPC55AG Manuale utente
Linksys
Linksys PLE200 - PowerLine AV EN Adapter Bridge Manuale utente
Linksys
Linksys WUSBF54G Manuale utente
Linksys
Linksys Small Business SPA2102 Manuale utente
Linksys
Linksys USB10T Manuale utente
Linksys
Linksys USB100TX - EtherFast 10/100 USB Network... Manuale utente
Linksys
Linksys SPA 2102 ATA Manuale utente
Linksys
Linksys WPC55AG Manuale utente
Linksys
Linksys PAP2T-NA Manuale di servizio
Linksys
Linksys WGA54AG Manuale utente
Linksys
Linksys WPC300N Manuale utente
Linksys
Linksys WPC51AB Manuale utente
Linksys
Linksys WPC55AG Manuale utente
