Linksys PAP2 Manuale utente

Configuration Guide

for the

Linksys PAP2

Landose Configuration Guide for the Linksys PAP2

SET UP YOUR PAP2

1. Using a standard telephone cable (RJ-11), connect an analog phone to the Phone1 port on the PAP2.

2. Using a standard network cable (RJ-45), connect the LAN port on the PAP2 to your network

connection (e.g., LAN).

3. Power on the PAP2 by plugging its power supply into an AC outlet and then plugging the power

cable into the Power port on the PAP2.

The table below lists some useful IVR options for the PAP2.

PAP2 MENU OPTIONS

ACTION CODE USER INPUT BEHAVIOR NOTES

Enter IVR Menu **** N/A

Wait until you hear the announcement,

“Configuration menu. Please enter

option followed by the pound (#) key,

or hang up to exit.”

Check DHCP 100 N/A

You will hear the system announce the

DHCP status, either enabled or

disabled.

Set DHCP 101 To enable, enter 1.

To disable, enter 0.

Press the number corresponding with

the desired option, followed by the

pound (#) key.

Check IP address 110 N/A

Set IP Address 111

Use the phone’s keypad to

enter the IP address. Press

the star (*) key to enter the

“dots” in the IP address.

After entering the IP address, press the

pound (#) key. Ensure that DHCP is

“Disabled.” If it is “Enabled,” the

system announces, “Invalid Option” if

you try to set this value.

Check Net Mask 120 N/A

Set Net Mask 121

Use the phone’s keypad to

enter the Net Mask address.

Press the star (*) key to enter

the “dots” in the IP address.

After entering the Net Mask address,

press the pound (#) key. Ensure that

DHCP is “Disabled.” If it is “Enabled,”

the system announces, “Invalid Option”

if you try to set this value.

Check Gateway 130 N/A

Set Gateway 131

Use the phone’s keypad to

enter the gateway address.

Press the star (*) key to enter

the “dots” in the IP address.

After entering the gateway address,

press the pound (#) key. Ensure that

DHCP is “Disabled.” If it is “Enabled,”

the system announces, “Invalid Option”

if you try to set this value.

Check MAC Address 140 N/A The system announces the PAP2’s MAC

address.

Check Firmware

Version 150 N/A The system announces the PAP2’s

firmware version.

Manual Reboot 7326668 N/A

Once the system announces, “Option

successful,” you may hang up the

phone. The PAP2 reboots automatically.

Page 1

Landose Configuration Guide for the Linksys PAP2

CONFIGURE YOUR PAP2 FOR OUTBOUND CALLING

To connect to the PAP2 Web interface:

1. Pick up the handset of the phone connected to the PAP2, and then, using the phone’s keypad, press

the star key (*) four times: ****.

2. When you hear an Interactive Voice Response (IVR) prompt, press 110#. When the system

announces the PAP2’s IP address, write it down.

To configure the PAP2 to make outbound calls:

1. Using a PC on the same network as the PAP2, launch a Web browser, and in the Address bar, enter

the PAP2’s IP address (obtained in the previous section).

2. Click the Admin Login link, located in the upper right-hand corner of the page.

3. Click the switch to advanced view link.

4. Click the tab for Line1 or Line2 at the top of the page, depending on which line you are configuring.

5. In the NAT Settings section, change the value of the following field:

NAT Keep Alive Enable—no

6. In the Proxy and Registration section, change the value of the following fields:

Proxy— sip.landose.com

Use Outbound Proxy— no

Use OB Proxy In Dialog— no

Make Call Without Reg— yes

Ans Call Without Reg— yes

DNS SRV Auto Prefix— no

7. In the Subscriber Information, enter No_Number in the Display Name field.

8. Enter the User ID (account number) and Password (passcode).

Note:

Line 1 and Line 2 must have a different account number and passcode.

9. Change the value of the Use Auth ID field to no.

Page 2

Landose Configuration Guide for the Linksys PAP2

Line 1 Configuration Page – Top

10. In the Audio Configuration section, change the value of the following fields:

Preferred Codec— G723

Use Pref Codec Only—no

G729a Enable—no

G723 Enable—yes

G726-16 Enable—no

Page 3

Landose Configuration Guide for the Linksys PAP2

G726-24 Enable—no

G726-32 Enable—no

G726-40 Enable—no

DTMF Tx Method—AVT

Line 1 Configuration Page – Bottom

11. In the Dial Plan section, change the value of the Dial Plan field to match the dialing pattern used in

your country (where you are using the Landose service).

For US calls, insert “1” as the first digit. For non-US calls, insert “011” before the rest of the phone

number. For information on customizing your dial plan, refer to the PAP2 manual.

12. To save these settings, click the Submit All Changes button.

13. On the Line 1 and Line 2 configuration pages of the Linksys PAP2, please change the following

settings in the Supplementary Service Subscription section from "Yes" to "No":

Three Way Call Serv

Three Way Conf Serv

Attn Transfer Serv

Unattn Transfer Serv

Page 4

Altri manuali per PAP2

Indice

Altri manuali Linksys Adattatore

Linksys

Linksys WAPPOE Manuale utente

Linksys

Linksys PAP2 Manuale utente

Linksys

Linksys WUSB54GS EU Manuale utente

Linksys

Linksys PCM1000 - Cisco 10/100/1000 CARDBUS MOBILE... Manuale utente

Linksys

Linksys WPC54GS - Refurb Wrls-g Notebook Adr Spdbstr No... Manuale utente

Linksys

Linksys Wireless-G Manuale utente

Linksys

Linksys WMA11B - Wireless-B Media Adapter Manuale utente

Linksys

Linksys WPC600N - Ultra RangePlus Wireless-N PC Card Manuale utente

Linksys

Linksys WUSB12 Manuale utente

Linksys

Linksys WGA54G Manuale utente

Linksys

Linksys PAP2 Manuale utente

Linksys

Linksys WPC300N Manuale utente

Linksys

Linksys WUSB54GC EU Manuale utente

Linksys

Linksys PAP2-T Manuale utente

Linksys

Linksys WMA11B - Wireless-B Media Adapter Istruzioni operative originali

Linksys

Linksys WUSB54GP Manuale utente

Linksys

Linksys Instant PowerLine PLUSB10 Istruzioni operative originali

Linksys

Linksys PAP2 Istruzioni operative originali

Linksys

Linksys Small Business SPA2102 Manuale operativo

Linksys

Linksys WGA600N - Wireless-N Gaming Adapter Bridge Manuale utente

Linksys

Linksys WPC200 Istruzioni operative originali

Linksys

Linksys PAP2 Manuale utente

Linksys

Linksys Instant Broadband Series Manuale utente

Linksys

Linksys WPC4400N Manuale operativo

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente