Linksys 921 Manuale utente
1
IP Phone - Linksys 921
Installation, Set-up and User Guide
June 2008
2
Installation
Phone will arrive via FedEx after placing order from your online account.
The phone is pre-provisioned at our shipping office. Installation is easy:
1. Plug long straightened end of the
coiled phone cord into back of phone.
Plug short straightened end into the
handset (not shown).
2. Plug power cord into phone (only use
power supply that came in the box).
3. Plug Cat 5 Ethernet cable into the
phone, connected to your network.
Phone now has dial-tone and is ready
for use!
Note: The handset cord is tucked behind the cardboard insert on the front
side of the box. You have to dig in to find it!
3
2
1
PC port not
available
3
Installation
Firewall Ports to Open:
IP Phones/ATA Adapters need port 5060 UDP and the range of 16384-
16482 UDP inbound and outbound open.
In some cases, multiple IP Phones/ATA Adapters on the same
network/router will need to change the 5060 port number to another
available port [examples: 5062, 5064, 5090…). This will mainly happen
with older routers, but some newer models may still be affected as well
and require a different port for each IP Phone/ATA Adapter.
4
Installation
Tip for Best Voice Quality:
A good internet connection is needed to maintain good voice quality.
We recommend a high speed DSL, cable or fiber connection with an
upload speed of 90kbps or greater.
We provision DigitalLine service at the "High/ Automatic" bandwidth
setting for better sound quality. If your broadband connection speed is
less than 90kbps (and you experience choppy voice quality),
you should adjust the bandwidth setting to "Low." To change phone’s
bandwidth connection, log into your online account, click Preferences,
then DigitalLines. Click the View link associated with the phone and
change the “Bandwidth Usage” setting.
To test your PC’s speed, visit
http://www.voipreview.org/voipspeedtester.aspx
Click the button in your online account for the User Guide and
additional help on this RingCentral product.
5
Set-Up
After installation, the phone will be automatically listed in the
assigned extension’s Forwarded Numbers list.
Check the Active box and inbound calls will ring on this device.
(404) 555-3245
6
Set-Up To change phone’s name, extension assignment, or
other provisioning actions, log into your online account,
click Preferences, then DigitalLines. Click the View link:
(404) 555-3245
(404) 555-3245
7
Set-Up
Bottom half of the view panel:
Enable to activate the red light at top of
the phone when new message arrives.
4045553245
8
Answering a call to your Local RingCentral number on the IP Phone
saves you money!
Andy, a Plus Plan customer, has two RingCentral numbers:
Phone Number Location
Main: (888) 555-5462 Toll Free
(248) 555-2386 Pontiac, Mi.
1 minute inbound call, under three scenarios:
Dials Local Number
(248) 555-2386
Dials TollFree
(888) 555-5462
$0.059
(Plus plan)
$0.000 ( Free* )
Dials Local Number
(248) 555-2386
$0.059
(Plus plan)
*Subject to Fair Use Policy
9
User Guide
10
IP Phone User Guide – Volume and Speaker Buttons
Volume Adjustment
Speaker Button
Using the Handset, Speakerphone or Headset
Calls can be made or received using the handset, speakerphone or headset and
you can switch audio devices during a call. Adjust the volume for the device you are
using with the volume adjustment bar.
Using the Handset
To place and answer calls using the handset, simply lift the handset.
Using the Speaker
To place and answer calls using the speaker, press the speaker button.
The green light behind the button will illuminate.
Using the Headset
Plug an approved headset with a 2.5mm connector into the headset port on the right
side of the phone. Press the headset button and the green light behind the button
will illuminate. For information on the exact models of headsets that are supported,
see the IP phone information on http://www.linksys.com
Switching Between the Handset/Headset/Speakerphone During a Call
Any of the audio devices can be used during a call. Only one device at a time can
be used. The handset can be on the hook when using the speakerphone or headset
function. If switching from the handset, make sure the speakerphone or headset
light is illuminated before placing the handset back on the hook.
Indice
Altri manuali Linksys Telefono IP
Linksys
Linksys SPA-941 Manuale utente
Linksys
Linksys SPA942 - Cisco - IP Phone Manuale utente
Linksys
Linksys WIP310 - iPhone Wireless VoIP Phone Manuale utente
Linksys
Linksys CIT300 Manuale utente
Linksys
Linksys WIP300 - iPhone Wireless VoIP Phone Istruzioni operative originali
Linksys
Linksys PHM1200 - One VoIP Phone Manuale utente
Linksys
Linksys WIP300 - iPhone Wireless VoIP Phone Manuale utente
Linksys
Linksys SPA921-NA Manuale di servizio
Linksys
Linksys 900 Series Manuale di servizio
Linksys
Linksys SPA942 - Cisco - IP Phone Manuale utente
Linksys
Linksys SPA962 Manuale utente
Linksys
Linksys SPA901 Manuale operativo
Linksys
Linksys SPA942 - Cisco - IP Phone Manuale operativo
Linksys
Linksys WIP330 - iPhone Wireless VoIP Phone Manuale utente
Linksys
Linksys SPA921 - Cisco - IP Phone Manuale utente
Linksys
Linksys SPA942 - Cisco - IP Phone Manuale utente
Linksys
Linksys SPA-941 Manuale utente
Linksys
Linksys SPA962 Manuale operativo
Linksys
Linksys SPA922 - IP Phone With Switch Manuale utente
Linksys
Linksys CIT300 Manuale utente
