Lippert Components Solera 795354 Istruzioni per l'installazione

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

Solera®Slide Topper

Access Kit

Installation and

Owner’s Manual

(For Aftermarket Applications)

Solera Slide Topper Access KitSolera Slide Topper Access Kit

Part #Part # Description

795354 Access Kit, Black

795355 Access Kit, White

NOTE: If the unit came with a pre-installed Solera® Slide

Topper Access Plate (Fig.1A or 2A),shown, it will require the

Solera Slide Topper Access Bracket (Fig.3A) provided in

this kit.

If the Solera Slide Topper Access Kit was purchased

then utilize these instructions for the Solera Slide Topper

installation process.

To reference components of the Solera Slide Topper,

please visit www.lci1.com under “Awnings.”

Table of Contents

Introduction ........................................... 2

Safety Information .................................... 2

Resources Required .................................. 2

Parts List ............................................... 3

Solera Slide Topper Access Kit ....................... 3

Prior to Installation .................................... 3

Installation ............................................. 3

Installing the Awning Rail ............................. 3

Assemble the Extension Rod and Cap ............... 4

Installation of the Access Plate if NOT Already installed

on the Unit ............................................ 4

Installing the Solera Slide Topper Access Bracket ... 5

Securing the Fabric ................................... 7

Troubleshooting ....................................... 7

Maintenance ........................................... 8

Fabric Care .......................................... 8

Notes ................................................... 8

NOTE: If the unit came with a pre-installed Solera® Slide

Topper Access Plate shown below (Fig.1A or 2A), the access

plates, part number 768004 or 768005 and screws part

number 793617 will not be needed for this installation.

Fig.1 Fig.2

Fig.3

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

Introduction

The Solera Slide Topper Access Plates are being utilized

by specific OEMs for prepping the unit to make installing

the Solera Slide Topper quicker and easier.

The Solera®Slide Topper is a high-quality, cost-effective

way to help keep slide-outs free of dirt, leaves and debris.

The Solera®Slide Topper is permanently attached to the

slide-out and retracts/extends with the room. The easy-

to-install kits are designed to fit rooms from 66” to 192” in

length.

The Solera®Slide Topper Access Kit comes complete with

mounting hardware.

Additional information about this product can be obtained

from lci1.com/support or by using the myLCI app.

Replacement kits can be ordered from https://store.lci1.

com/ or by using the myLCI app.

The myLCI app is available for free on iTunes®for iPhone®

and iPad®and also on Google Play™for Android™users.

iTunes ®, iPhone®, and iPad®are registered trademarks of

Apple Inc.

Google Play™and Android™are trademarks of Google Inc.

Safety Information

Read and fully understand all instructions before installing

or operating this product.

Adhere to all safety labels.

This manual provides general installation procedures.

Many variables can change the circumstances of the

procedure, i.e., the degree of difficulty involved in the

service operation and the ability level of the individual

performing the operation.

This manual cannot begin to plot out procedures for every

possibility, but will provide the general instructions for

effectively installing the system. In the event the skill level

required is too advanced or the procedure too difficult,

a certified technician should be consulted before

performing the necessary installation. Failure to correctly

install the system may result in voiding the warranty,

inflicting injury or even death.

FAILURE TO FOLLOW THE INSTRUCTIONS

PROVIDED IN THIS MANUAL MAY RESULT IN DEATH,

SERIOUS INJURY, UNIT DAMAGE OR VOIDING OF

THE COMPONENT WARRANTY.

ALWAYS WEAR EYE PROTECTION WHEN

PERFORMING SERVICE OR MAINTENANCE TO THE

UNIT. OTHER SAFETY EQUIPMENT TO CONSIDER

WOULD BE HEARING PROTECTION, GLOVES AND

POSSIBLY A FULL FACE SHIELD, DEPENDING ON

THE NATURE OF THE SERVICE.

MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP

CLEAR AND USE CAUTION.

Resources Required

• 1-2 people, depending on task

• Cordless or electric drill or screw gun

• Appropriate drive bits

• Screwdriver

• (2) #6 x ½” hex head screws

• 1/8” Hex key wrench

• Tape measure

• Silicone sealant or butyl tape

• Silicone lubricant

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

Prior to Installation

The unit will be equipped with a removable, cosmetic

access plate cover (Fig.4A) on the access plate (Fig.4B).

This cover snaps on and off and must be removed prior to

installation of the access bracket.

Parts List

NOTE: Part numbers are shown for identification purposes

only. Not all parts are available for individual sale. All parts

with a link to the Lippert Store can be purchased.

Solera Slide Topper Access Kit

For units with the Solera Slide Topper Access Plate

already attached.

Solera Slide Topper Access Kit - WhiteSolera Slide Topper Access Kit - White

LetterLetter PNPN DescriptionDescription QtyQty

A 768008 Access Bracket 2

B 768005 *Access Plate 2

C 786718 Set Screw, 1/4” - 20 x 1/2” 4

D 793617 *Screw, #10 - 13 x 1 1/4” 10

Solera Slide Topper Access Kit - BlackSolera Slide Topper Access Kit - Black

LetterLetter PNPN DescriptionDescription QtyQty

A 768007 Access Bracket 2

B 768004 *Access Plate 2

C 786718 Set Screw, 1/4” - 20 x 1/2” 4

D 793616 *Screw, #10 - 13 x 1 1/4” 10

Fig.4

Installation

All screws supporting the awning assembly MUST have a

backer within the structure of the wall of the unit. Refer to

unit manufacturer for proper location.

Installing the Awning Rail

Awning rail included.

1. Position the awning rail along the line where the roof and

wall meet or a minimum of 3” above the upper edge of the

slide room the Solera®Slide Topper will cover. The awning

rail must be level and parallel with the top of slide room box

of the unit.

NOTE: If mounting the Solera Slide Topper access plate

on the T-molding, see (Fig.2), the awning rail must be a

minimum of 4 ½” above the upper edge of the slide room

the awning will cover.

2. After determining the awning rail’s proper location, mark

its position with a non-permanent method of marking.

3. Apply sealant along the horizontal length of the back

(Fig.5A) of the awning rail.

4. Align the awning rail on the wall and secure with

#8 - 18 x 1” screws, using all fastener holes.

* If the Access Plate is already installed on the unit these

parts will not be needed for this installation.

Fig.5

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

Fig.6

Fig.7

Assemble the Extension Rod and Cap

1. Slide the extension rod (Fig.6A) into the spring head

assembly torsion arm (Fig.6B), aligning the fastener

locations (Fig.6).

2. Slide the spring head assembly torsion arm end cap

(Fig.6C) into the extension rod (Fig.6A), aligning all three

fastener locations (Fig.6). Fasten using the provided

 screw (Fig.7).

3. Repeat steps 1 and 2 for the opposite end.

fastener locations

Fig.8

Installation of the Access Plate if NOT Already

installed on the Unit

1. If The access plate (Fig.8) has NOT already been

(Fig.8A) at

the top or bottom, depending on which option allows for a

more square installation on the unit.

2. Install the access plate below the T-molding (Fig.9) or on

the T-molding (Fig.10).

Fig.9 Fig.10

A. If installing below the T-molding, start on one side of

the front of the slide-out by placing one of the two access

brackets (Fig.11A) against the bottom of the T-molding at

the top corner of the slide-out (Fig.11B) as close to the

corner as possible. Keep the mounting bracket parallel

with the bottom edge of the T-molding.

Fig.11

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

1. Slide an access bracket onto an access plate at the

appropriate position (Fig.14 or Fig.15) at both ends of the

slide room.

NOTE: There might be a slight gap between the T-molding

side and the side of the mounting bracket (Fig.11C) if the

corner does not have a 90 degree angle.

B. If installing on the T-molding, start on one side of

the front of the slide-out by placing one of the two

access brackets (Fig.12A) at the very bottom corner of

the T-molding, (Fig.12B) as close to the outside of the

T-molding as possible without going over the corner mold

(Fig.12C).

NOTE: Make sure the screws do not go over the roof line.

Fig.14

Fig.12

3. Fasten the mounting bracket to the slide-out exterior

¼” recessed

square head screws (Fig.13).

Fig.13

FALLING SLIDE TOPPER ACCESS BRACKETS

CAN CAUSE PERSONAL INJURY, PRODUCT AND/

OR PROPERTY DAMAGE. SLIDE TOPPER ACCESS

BRACKETS ARE INSTALLED LOOSE ON THE ACCESS

PLATE UNTIL FINAL INSTALLATION. MAKE SURE

ACCESS BRACKETS ARE SECURE ENOUGH TO

PREVENT FALLING FROM THE ACCESS PLATE.

Installing the Solera Slide Topper Access Bracket

NOTE: The Solera Slide Topper Access Bracket can be

installed in two different positions. The lower position

(Fig.14A), first extrusion from the top of the access bracket,

is used for regular clearance. The higher position (Fig.15A),

second extrusion from the top of the access bracket, is

used if the slide topper requires extra clearance.

NOTE: If installing the slide topper access plate on the

T-molding, see (Fig.2), use the first extrusion from the top of the

access bracket method (Fig.14A).

access

plate

access

plate

Fig.15

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

4. Remove packaging from the roll tube and unroll a small

portion of fabric, no more than one turn.

Fig.17

NOTE: The original extension rod brackets in the Solera

Slide Topper Kit will not be needed

Installing the Solera Slide Topper Assembly

1. To prepare for fabric installation, use a screwdriver to

spread open either end of the awning rail on the installation

end (Fig.16A).

2. To protect the fabric from damage during installation,



3. Spray the inside of the awning rail channel with silicone

lubricant (Fig.16B).

Fig.16

UNROLLING THE FABRIC MORE THAN ONE TURN

WILL CAUSE THE SLIDE TOPPER TO LOSE TENSION

AND CREATE SLACK WHEN CLOSING THE SLIDE

ROOM. MAKE SURE TO LEAVE THE SLIDE ROOM

CLOSED OR NOT TO EXTEND MORE THAN 6”.

fabric

5. Using at least two people, feed the polycord (Fig.17A) on

the fabric through the awning rail channel (Fig.17B).

6. Feed one of the extension rods (Fig.18A) into an access

bracket (Fig.18B). By pulling the extension rod all the way

into the access bracket, the opposite end extension rod

can now slide into the access bracket at the opposite end.

Fig.18

NOTE: If needed, the access brackets can slide left or right

to assist in getting both extension rods into the access

brackets.

7. Position the extension rod so that the roll tube will not

be touching the slide room.

8. Install the two provided ¼” - 20 x ½” set screws in the

top two holes of the access bracket (Fig.19) if using the

lower position (Fig.7). Install two set screws in the lower

two holes of the access bracket (Fig.20) if using the higher

position (Fig.8).

Fig.19

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

9. Center the Solera®Slide Topper over the slide room

using a tape measure.

Troubleshooting

What’s Happening? What Should Be Done?

Rub marks appear on the fabric. Check that there is no debris in the track where fabric goes into the case.

Fabric sags or is loose. Check tension on springs.

Make sure the end caps are properly secured.

Fabric will not roll up. Check tension on springs.

Make sure there are no debris or foreign objects in the fabric opening or case.

Fabric will not unroll. Make sure the spring clip that lock the tension for install have been removed

from both ends of the end caps.

Fabric appears to roll up

at an angle.

Make sure the rail that is mounted to the unit is square with the main housing

of the slide topper.

Make sure fabric is cut square.

Securing the Fabric

1. Extend and retract the room several times to ensure

that the fabric is square on the roll tube.

2. Secure the fabric (Fig.22A) in the awning rail (Fig.15B) no

more than 1” inside the edge of the fabric on both ends

using a #6 x ½” hex head screw (Fig.22C). Install the screw

(Fig.15C) down through the awning rail (Fig.22B) into the

fabric (Fig.15A) and the polycord (Fig.15D).

outer edge

of fabric

Fig.22

ROLL TUBE SPRINGS ARE UNDER TENSION.

IMPROPERLY SECURED ROLL TUBE SPRINGS CAN

CAUSEPERSONALINJURYAND/OR PRODUCTDAMAGE.

SLOWLY RELEASE SPRING TENSION TO AVOID

PERSONAL INJURY AND/OR PRODUCT DAMAGE.

Fig.20

Fig.21

10. Fasten the extension rods (Fig.21A) to the access

brackets (Fig.21B) by installing two of the provided

#10 - 16 x ¾” self-drilling hex washer head screws (Fig.21).

11. Firmly hold the roll tube when removing the spring clip

to relieve spring tension.

lci1.com 574-537-8900 Rev: 09.17.20

Solera®Slide Topper

Access Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0002640

Manual information may be distributed as a complete

document only, unless Lippert Components provides

explicit consent to distribute individual parts.

All manual information is subject to change without

notice. Revised editions will be available for free

download at lci1.com. Manual information is considered

factual until made obsolete by a revised version.

Please recycle all obsolete materials and contact

Lippert Components with concerns or questions.

NotesMaintenance

Fabric Care

If the Slide Topper is retracted while wet, extend the

Slide Topper and let it dry as soon as conditions allow

before retracting. This will help prevent the formation of

mildew and add greatly to the life of the awning. Mildew

does not form on the fabric itself, but on the accumulated

dust, dirt and grime.

Periodically clean vinyl or woven acrylic fabric using a

mixture of ¼cup of dish soap and five gallons of warm

water. Liberally apply the mixture on the top of the fabric

and retract the Slide Topper for five minutes. This will

apply the mixture to the bottom of the fabric as well.

Extend the Slide Topper and hose off with fresh water.

Repeat if necessary. Allow fabric to dry before retracting.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lippert Components Accessori

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera 3000WS Series Manuale utente

Lippert Components

Lippert Components Solera Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera 674282 Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Classic Manuale utente

Lippert Components

Lippert Components Awnbrella Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera 434718 Manuale utente

Lippert Components

Lippert Components Solera Classic Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components SURESHADE ATF Guida rapida

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Smart Arm Manuale utente

Lippert Components

Lippert Components Solera Smart Arm Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Edge Awning Manuale utente

Lippert Components

Lippert Components Solera 759516 Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Power Awning Manuale utente

Lippert Components

Lippert Components Solera Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente