Lippert Components Solera Manuale utente

Rev: 09.19.2016 Page 1 TI-147

SOLERA®MANUAL AWNING INSTALLATION INSTRUCTIONS

TI-147

AWNINGS

Prior To Installation

NOTE: All screws/rivets supporting awning assembly MUST have a backer within the structure of the wall of

the coach.

Resources Required

• Three people

• Drill or cordless screw gun

• #2 square screwdriver bit

• ⁄" nut driver bit and/or rivet gun

Installation

NOTE: If installing a Pull Strap Awning, refer to TI-163 for instructions to mount heads to roll tube.

1. Attach the awning heads to the support arm assemblies by screwing the ⁄”-18 x 2 ¼” bolts (266148) into the

ends of the support arms and tightening the bolts (Fig. 1).

2. With two people holding the support arms, one at either end of the awning assembly, a third person needs

to line up the fabric cord with the awning rail that has been installed on the coach. Slide the fabric cord the

length of the awning rail.

NOTE: Do not unravel fabric more than one full revolution for installation or the tension will be too weak to retract

properly.

3. Set the awning assembly to the desired height and attach it to the side of the coach with two #14 x 1 ½” screws

(286576) at the top (Fig. 2) and two #14 x 1 ½” (286576) screws at the bottom (Fig. 3).

NOTE: Make sure the awning assembly is square on the unit prior to mounting the bottom 2 screws.

4. Remove the cotter pin from each head assembly. Extend the awning half way out. Secure the middle of the

wall mounting channel with two #14 x 1 ½” screws (286576) at any of the three locations shown (Fig. 4). Repeat

this process for other side of awning assembly.

NOTE: Four rivets with ⁄" grip range can be used in place of the two middle and two lower screws on laminated

walls.

286576

266148

Possible

screw / rivet

locations

Fig. 1 Fig. 2

Fig. 3

Fig. 4

Rev: 09.19.2016 Page 2 TI-147

MANUAL AWNING INSTALLATION INSTRUCTIONS

TI-147

AWNINGS

Securing The Fabric

1. Roll the awning in and out several times to ensure that the fabric is square on the roll tube.

2. Secure the fabric in the awning rail by installing a #6 x ½” hex head screw through the fabric cord and

fabric 1” inside the edge of the fabric on both sides (Fig. 5).

NOTE: Seal all wall penetrations to protect against water intrusion (Fig. 6).

NOTE: All Solera Awnings 21' and under DO NOT require a center support or cradle.

Fig. 5

Fig. 6

As a supplier of components to the RV industry, safety, education and customer satisfaction are our primary concerns. Should you

have any questions, please do not hesitate to contact us at (574) 537-8900 or by email at [email protected]. Self-help tips,

technical documents, product videos and a training class schedule are available at www.lci1.com or by downloading the MyLCI app.

Altri manuali per Solera

Indice

Altri manuali Lippert Components Accessori

Lippert Components

Lippert Components Edge Awning Manuale utente

Lippert Components

Lippert Components Solera Slide Topper Istruzioni per l'installazione

Lippert Components

Lippert Components Solera 795354 Istruzioni per l'installazione

Lippert Components

Lippert Components Solera TI-278 Istruzioni operative e di manutenzione

Lippert Components

Lippert Components Solera Classic Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Classic Awning Manuale per l'uso e la cura

Lippert Components

Lippert Components Solera 674282 Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Power Awning XL Manuale utente

Lippert Components

Lippert Components Solera Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Classic Manuale utente

Lippert Components

Lippert Components Solera Smart Arm Manuale utente

Lippert Components

Lippert Components Solera 434718 Manuale utente

Lippert Components

Lippert Components Solera Slide Topper with Access Plates Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Classic Awning Manuale utente

Lippert Components

Lippert Components SURESHADE ATF Guida rapida

Lippert Components

Lippert Components Solera Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Solera Manuale utente

Lippert Components

Lippert Components Awnbrella Istruzioni per l'installazione

Lippert Components

Lippert Components 2021130659 Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Smart Arm Istruzioni per l'installazione

Lippert Components

Lippert Components Solera Power Awning Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente