Lippert Components SOLIDSTEP 2.0 Manuale utente
Master Owner's Manual
Steps
User notice
The Table of Contents is an interactive field. Click on the desired
section to be taken immediately to the corresponding page.
TABLE OF CONTENTS
MANUAL STEPS 4
Introduction 4
Safety 4
Step Operation 5
Unfolding Steps 5
Folding Steps 5
Maintenance 5
Scratches 5
Lubrication 5
Anti-Skid Tape 5
SOLIDSTEP®2.0 6
Introduction 6
Safety Information 6
Operation 7
Release Steps 7
Storage of Steps 7
Adjust Leg Extension 7
SOLIDSTEP®3.0 9
System Information 9
Safety information 9
Operation 10
Release Steps 10
Storage of Steps 10
Adjust Leg Extension 10
VICTORY STEP™ 12
Introduction 12
Safety 12
Step Operation 13
Step Deployment 13
Height Adjustment 14
Step Removal 14
Handrail (if equipped) 15
Installation 15
Removal 16
Stowage 16
Storage of Victory Step (if installed) 16
Storage 16
Removal 17
Master Owner's Manual
The Master Owner's Manual is intended to provide information on Lippert Components Inc.'s most widely-
used products. Products described in the Master Owner's Manual may not be on every trailer. The trailer may
also have products not included in this manual. All manual information is subject to change without notice.
Revised editions will be available for free download at lci1.com/support. Manual information is considered
factual until made obsolete by a revised version. Manual information may be distributed as a complete
document only, unless Lippert Components provides explicit consent to distribute individual parts.
Rev: 11.08.19 Page 4 CCD-0001573-11
Moving parts can pinch, crush or cut. Keep clear and use caution.
The “WARNING” symbol above is a sign that an installation procedure has a safety risk involved and
may cause death or serious injury if not performed safely and within the parameters set forth in
this manual. The trailer MUST be supported per manufacturer's recommendations before working
underneath. Failure to do so may result in death, serious personal injury or severe product or
property damage.
Introduction
This document details the operation and maintenance of manual steps.
Safety
STEPS
MANUAL STEPS
Rev: 11.08.19 Page 5 CCD-0001573-11
Step Operation
Unfolding Steps
1. Pull out on the top lip of the step vertically stored (Fig. 1A).
2. Pull up and out on the back of step resting on the second step (Fig 2A).
3. Unfold bottom step (Fig. 3).
Folding Steps
1. Pull up on bottom step and fold over the second step (Fig. 2A).
1. Pull up on bottom of steps and fold inward under top step (Fig. 1A).
Maintenance
Scratches
1. Clear any chipped paint or material adhering to scratched area.
2. Apply automotive grade primer to scratch.
3. Paint primed area with automotive high gloss paint.
Lubrication
1. Remove all dirt and foreign matter from hinge areas.
2. Lubricate hinge areas in between the sheet metal portions of the steps.
NOTE: Utilize a dry silicone lubricant. Wet lubricants will attract dirt and possibly cause damage to the
hinge areas.
Anti-Skid Tape
1. Inspect steps for loose, missing or damaged anti-skid tape.
2. Replace anti-skid tape as necessary.
Fig. 1
A
A
Fig. 2 Fig. 3
Rev: 11.08.19 Page 6 CCD-0001573-11
Introduction
The SolidStep® 2.0 is a trailer entry step assembly mounted to the side of any trailer, providing an ease of
entry, regardless of level ground.
Safety Information
Failure to follow the instructions provided in this manual may result in death, serious personal
injury, product or property damage, or voiding of the component warranty.
No repairs should be attempted by anyone other than a qualied professional. The deployment
and retraction of the Step assembly can cause injury if proper precautions are not taken. The Step
assembly was designed for an operational weight rating of 400 lbs.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Always wear eye protection when performing service or maintenance to the trailer. Other safety
equipment to consider would be hearing protection, gloves and possibly a full face shield,
depending on the nature of the service.
SOLIDSTEP®2.0
STEPS
Rev: 11.08.19 Page 7 CCD-0001573-11
Operation
Release Steps
1. Disengage transport lock (Fig. 1).
2. Firmly grasp and pull out the vertically stored SolidStep and firmly rest it on the ground.
3. Adjust leg extensions as needed, see Leg Extension Adjustment section.
Fig. 1
Storage of Steps
1. Retract leg extensions, if desired.
2. Lift up SolidStep to its stored position and make sure the transport lock has been engaged.
Adjust Leg Extension
The leg extension is secured with a quick release clevis pin. Adjustments can be made to the leg extensions
in 1" increments by moving the inner leg up or down for the optimal angle and to adjust for the ground
surface angle.
Transport Lock
Moving parts can pinch, crush or cut. Keep clear and use caution.
1. To extend the inner leg (Fig. 2B):
A. Remove the quick release clevis pin (Fig. 2A) from the tube and the slot in the angle.
B. Extend the inner leg to the ground and at an angle so the steps are parallel to the ground and are
level.
C. Replace the quick release clevis pin in the tube and slot and into the closest inner leg hole that
intersects with the outer leg's slot to where the inner leg and the outer leg (Fig. 2C) meet.
A
B
C
Fig. 2
Rev: 11.08.19 Page 8 CCD-0001573-11
2. To retract the inner leg:
D. Remove the quick release clevis pin from the outer and inner legs.
E. Retract the inner leg.
F. Reinstall the quick release clevis pin into the outer leg slot and into the closest inner leg hole that
intersects with the outer leg's slot.
G. The step assembly is shown in the upright stored position, as viewed from underneath the step
assembly in figure 3.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Transport Lock
Fig. 3
Rev: 11.08.19 Page 9 CCD-0001573-11
System Information
The SolidStep® 3.0 is a trailer entry step assembly mounted to the side of any trailer, providing an ease of
entry, regardless of level ground.
NOTE: Step identification tags are located under one of the step extrusions, typically the top full step.
Failure to follow the instructions provided in this manual may result in death, serious personal
injury, product or property damage or voiding of the component warranty.
Always wear eye protection when performing service or maintenance to the trailer. Other safety
equipment to consider would be hearing protection, gloves and possibly a full face shield,
depending on the nature of the service.
No repairs should be attempted by anyone other than a qualied professional. The deployment
and retraction of the step assembly can cause injury if proper precautions are not taken. The step
assembly was designed for an operational weight rating of 400 lbs.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Safety information
SOLIDSTEP®3.0
STEPS
Rev: 11.08.19 Page 10 CCD-0001573-11
Operation
Release Steps
1. Disengage transport lock (Fig. 1).
2. Firmly grasp and pull out the vertically stored SolidStep and firmly rest it on the ground.
3. Adjust leg extensions as needed, see Leg Extension Adjustment section.
A
B
C
Storage of Steps
1. Retract leg extensions, if desired.
2. Lift up SolidStep to its stored position and make sure the transport lock has been engaged.
Adjust Leg Extension
The leg extension is secured with a quick release clevis pin. Adjustments can be made to the leg extensions
in 1" increments by extending or retracting the inner leg for the optimal angle and to adjust for the ground
surface angle.
1. To extend the inner leg (Fig. 2B):
A. Remove the quick release clevis pin (Fig. 2A) from the tube and the slot in the angle.
B. Extend the inner leg to the ground and at an angle so the steps are parallel to the ground and
level.
C. Reinsert the quick release clevis pin into the tube and slot closest to where the inner leg and tube
(Fig. 2C) meet.
2. To retract the inner leg:
A. Remove the quick release clevis pin from the tube and slot.
B. Retract the inner leg.
C. Reinsert the quick release clevis pin into the tube and slot.
Fig. 1
Transport Lock
Fig. 2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Lippert Components Attrezzature industriali
Lippert Components
Lippert Components Happijac Manuale utente
Lippert Components
Lippert Components Power Gear 82-L0356 Manuale utente
Lippert Components
Lippert Components Solera 728810 Istruzioni per l'installazione
Lippert Components
Lippert Components Equa-Flex Triple Axle Istruzioni per l'installazione
Lippert Components
Lippert Components Level Up LCD Travel Trailer Manuale utente
