Lippert SolidStep 4.0 Manuale utente
SolidStep®4.0
OWNER'S MANUAL
Rev: 10.04.23 Page 2 CCD-0007740
TABLE OF CONTENTS
Introduction 2
Safety 2
Operation 4
Release Steps 4
Leg Extension Adjustment 5
Securing and Storing the Steps 5
Adjusting the Transport Lock 6
Notes 7
Introduction
The SolidStep® 4.0 is a trailer entry step assembly that can be mounted to the side of any trailer, providing
an ease of entry, regardless of level ground.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Additional information about this product can be obtained from lci1.com/support or by downloading
the free LippertNOW app. The app is available on Apple App Store® for iPhone® and iPad® and also on
Google Play™ for Android™ users.
Apple App Store®, iPhone®, and iPad® are registered trademarks of Apple Inc.
Google Play™ and Android™ are trademarks of Google Inc.
For information on the assembly or individual components of this product, please visit:
https://support.lci1.com/steps-support-solidstep.
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death or serious personal injury if not performed safely and within the parameters set forth in this
manual.
Failure to follow instructions provided in this manual may result in death, serious personal injury
and/or severe product and property damage, including voiding of the component warranty.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage,
including voiding of the Lippert limited warranty.
Rev: 10.04.23 Page 3 CCD-0007740
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury
and/or product or property damage if not safely adhered to and within the parameters set forth
in this manual
Always wear eye protection when performing service, maintenance or installation procedures.
Other safety equipment to consider would be hearing protection, gloves and possibly a full face
shield, depending on the nature of the task.
Moving parts can pinch, crush or cut. Keep clear and use caution.
No repairs should be attempted by anyone other than a qualied professional. The deployment and
retraction of the step assembly can cause injury if proper precautions are not taken. The step
assembly was designed for an operational weight rating of 400 lbs.
Rev: 10.04.23 Page 4 CCD-0007740
Operation
Moving parts can pinch, crush or cut. Keep clear and use caution.
Release Steps
1. From the stowed position (Fig. 1), disengage the transport lock (Fig. 1A) by pulling the transport lock
knob to the right.
2. Firmly grasp and pull out the vertically stored SolidStep 4.0 and rest it firmly on the ground.
3. Adjust leg extensions as needed.
Fig. 1
A
B
Rev: 10.04.23 Page 5 CCD-0007740
Leg Extension Adjustment
The leg extension is secured with a spring-loaded catch pawl (Fig. 2A). Adjustments can be made to the leg
extensions in 1" increments by extending or retracting the inner leg for the optimal angle and to adjust for
the ground surface angle.
1. Pull the spring-loaded catch pawl (Fig. 2A) up to release it from the tube and the slot
in the angle.
2. Extend or retract the inner leg (Fig. 3A) as needed so the steps are parallel to the ground and level
when extended, and unobtrusive while retracted.
3. When the leg is at the desired position, release the spring-loaded catch pawl into the tube and slot
closest to where the inner leg and tube meet to lock them (Fig. 4).
Fig. 2 Fig. 3
Fig. 4
A
A
Securing and Storing the Steps
1. Retract leg extensions. See Leg Extension Adjustment section.
2. Lift up SolidStep 4.0 to its stored position (Fig. 1) until the transport locks engage and click into place.
3. Make sure the latches (Figs. 6A and 7A) are resting against the door frame.
4. Once the transport lock has been engaged, test its functionality by shaking the step assembly to
simulate road vibration, making sure that the SolidStep 4.0 is secure.
Rev: 10.04.23 Page 6 CCD-0007740
Fig. 5
A A
Adjusting the Transport Lock
1. To verify the transport lock adjustment is working properly, the SolidStep 4.0 should be in the stored
position (Fig. 5). Make sure transport latch flanges (Figs. 5A, 6A, and 7A) are resting against the door
frame. If final adjustment is required, loosen the two bolts (Fig. 6B and Fig. 7B) on either side of the
adjustable transport lock. This allows for side-to-side adjustment in the latch mechanism.
Attempting to engage the transport lock without proper adjustment may cause damage to the door
frame or step assembly.
Fig. 6
B
B
A
Fig. 7
B
B
A
Rev: 10.04.23 Page 7 CCD-0007740
Notes
The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or
dissemination of portions of this manual unless prior written consent from an authorized Lippert representative
has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this
manual is subject to change without notice and at the sole discretion of Lippert. Revised editions are available
for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact Lippert
Indice
Altri manuali Lippert Accessori per automobili
Lippert
Lippert ARIES S224050 Manuale utente
Lippert
Lippert VELA POP-UP ROOF Manuale utente
Lippert
Lippert SMART BED UNIVERSAL KIT Manuale utente
Lippert
Lippert Curt 60654 Manuale utente
Lippert
Lippert Vela Manuale utente
Lippert
Lippert OneControl Manuale utente
Lippert
Lippert Curt 18415 Manuale utente
Lippert
Lippert Stargazer Nano Long Skylight Manuale utente
Lippert
Lippert FLYSCREEN N Series Manuale utente
Lippert
Lippert LUVERNE 401720 Manuale utente
Lippert
Lippert SolidStep Gen 2 Istruzioni per l'installazione
Lippert
Lippert ARIES 2500207 Manuale utente
Lippert
Lippert Tire Linc 2020106863 Istruzioni per l'installazione
Lippert
Lippert 2021000090 Istruzioni per l'installazione
Lippert
Lippert Curt 18110 Manuale utente
Lippert
Lippert Stargazer Spirit XTR Manuale utente
Lippert
Lippert Project 2000 Sliding Step Manuale utente
Lippert
Lippert RV ENTRY DOOR Manuale utente
Lippert
Lippert Curt 16613 Manuale utente
Lippert
Lippert Tire Linc Istruzioni per l'installazione
