Liyu Lyric XFULL Series Manuale utente
MANUAL
XFULL
SERIES
- -2
Dear customers:
Please read this manual throughly before using Lyric XFULL series ink-jet
printers.
Catalog
1. Safety Instructions……………………………………… page 3
2. Installation and Troubleshooting..………………………. page 5
3. Appearance and Components…………………………… page 13
4. Operation Instructions……………………………………page 16
5. Technical Specifications………………………………….page 26
6. Maintenance…………………………………………….. page 27
7. Warranty Items………………………………………….. page 29
- -3
Chap 1 Safety instructions
Please read the following directions thoroughly before you start to use this
machine:
1. You should place the printer in a room what is,
◆ clean and breezy with flat ground;
◆ anti-electromagnetic, quakeproof and without heavy dirty;
keep the ambient conditions always be at temperature: 20~25℃and
humidity: 40%~70%RH.
2. Connect the printer and PC to a reliable outlet well grounded, and a
one-meter-long pontil planted in the salted soil is also suggested for
ground connection.
3. Do not pull or plug the print cable between the printer and PC with power,
and do wait 10 seconds before you need to turn on the power again.
4. Adoption of high quality solvent inks is necessary for the printer; If you
need to change the ink of different brand please do contact with the local
dealer.
5. When using the machine, pay attention to that,
◆ Do not press the machine cover by hand or other heavy things;
◆ Do remember to turn on / off by power switch;
◆ Printing directly on the printer plate without PVC banner is
- -4
prohibited!
6. If you encounter the following troubles, please cut off the power at once
and contact with the local dealer,
7. If you encounter the following troubles, please cut off the power at once
and contact with the local dealer,
◆ Power switch is out of control or damaged;
◆ Cannot operate it normally or some obvious changes of machine
preferences occur.
- -5
Chap 2 Installation and Troubleshooting
1. Packing box
(1.1) one host machine;
(1.2) one set of machine stand as follows,
NO. Items QTY.
1 Left and right column Per 1
2 Crossbeam 1
3 Roller for feeding 2
4 Roller for take up 2
5 Left and right holder for paper roller Per 1
6 Stand pillar 2
7 Sub power switch 1
8 Pulling system 1
9 Tighten kits 1 bag
10 Left and right holder for pulling
system and connection board
Per 1
11 Fixed peg for crossbeam 2
12 Ink Collection Plate 1
13 Connection board for column 4
(1.3) one set of accessories see as follows,
- -6
NO. Items QTY.
1 Power cable 2
2 Printcable 1
3 Cleaner cloth and nylon tube 1bag& 2
4 Main and sub tank per 1
5 Usermanual 1
6 Inner hexagon spanner (S=2) 1
7 Inner hexagon spanner (S=3) 1
8 Inner hexagon spanner (S=5) 1
9 Inner hexagon spanner (S=6) 1
10 “O”ring 8
11 RIP software 1
12 PCI card 1
2. Installation (referring to the fig.1)
- -7
(2.1) Stand installation,
Referring to the above figure, install the stand in following steps,
① Draw out the plug and wire from the crossbeam first, through the
right column then take them out from the side hole in it, now you can
connect the crossbeam with left/right column by fixed peg kits;
② Connect the left/right pillars to the columns, and adjust the 4 wheels
on pillar to be stable;
③ Connect the left/right holder for paper roller with the columns, then
install the sub power switch to the right column.
④ Place the host machine on the stand and well tightened to be stable
with tighten kits;
(2.1) Installation of the PCI card and driver
First, please make sure the computer is powered off, open the PC case and
insert the PCI card into the PCI slot of the mainboard. If you are not familiar
with this kind of operation, please let the professionals do it for you to avoid
the hardware damage. If the manufacturer of your computer do not allow
you open the PC case, please contact their service department and let them
do it for you to avoid unexpectable troubles.
After successful installation of the PCI card, please connect the PCI card and
the printer with the print cable which is in the accessories. Then turn on the
power for computer, the operation system will find the new PCI card and
require the corresponding driver, please install the driver as follows
(Windows XP as an example):
- -8
First is the ‘Found New Hardware Wizard’, please put the accessory cd
into the cd-rom and click ‘next’;
select ‘Don’t search. I will choose the driver to install’, click ‘next’;
- -9
Click “Have Disk”, to show “Install From Disk” interface, Click “Browse”
to Select LiYuPciDriver.inf document under driver directory in CD,
click ‘OK’,
- -10
select ‘LYRIC JetPlot Card’, then click ‘next’, the windows will start the
installation automatically. After that, restart the computer, then the
Installation is complete.
(2.2) Electric installation
① Connect the 3-pin plug-in of the media motor and the 3-pin socket
on the sub power switch.
② Connect the 4-pin plug-in of the media sensor and the 4-pin
socket on the sub power switch.
③ Connect the out-put power socket on the sub power switch with
the power socket on the right bottom of the printer by the
accessory power cable. (or Find the accessory power cable, one
end connect to the out-put power socket on the sub power switch,
the other end connect to the power socket on the right bottom of
the printer) Test whether the panel is heated or not by push the
Questo manuale è adatto per i seguenti modelli
6
Indice
