Lockly SECURE PRO Manuale utente
LATCH EDITION
INSTALLATION
GUIDE
SECURE PRO
Go to Lockly.com/installation to watch a video
version of this installation guide.
Download the BILT app in the App Store or on
Google Play for step-by-step interactive 3-D
walk-through installation instructions.
OR
Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly Secure Pro up and running.
Installation generally takes less than 30 minutes. If you
have any questions please reference our online support
at: Lockly.com/support or call (669) 500-8835 for help.
3
To complete the installation you will need:
Preparation
Phillips Screwdriver Flathead Screwdriver Tape measure or ruler
Pliers
（Optional）
Screwdriver with drill bits
Drilling is not required to install the lock, and is optional. However if you are installing
your lock on a brand new door, a drill is required if there are no holes prepared for
lock installation.
4
Preparation
IMPORTANT NOTICE
*You are not required to drill an extra hole on your door. We have provided double sided
Adhesive tape for you to help stabilize the lock during installation. Only drill a hole if you
wish to have added stability. Please refer to the provided template for drilling if needed.
Use goggles to protect eyes if you need to drill door holes.
Remove existing door hardware, latch or deadbolts before installing the new lock.
Use provided template to bore new holes if needed.
1
2
3
4
1-3/8" ~ 2"
(35mm ~ 50mm)
2-1/8"
54mm
1"
25mm
Backset
2-3/8" (60mm)
or 2-3/4" (70mm)
*
Measure and confirm your door is
between 1-3/8" ~
2" (
35mm - 50mm).
Measure and confirm the hole in the
door is 2-1/8" (54mm) .
Measure and confirm that the backset
is between 2-3/8" (60mm) to 2-3/4" (70mm).
Measure and confirm that hole in the
door edge is 1" (25mm).
*Optional
5
INSTALLING THE LOCKSET
Step 1
Facing the door exterior, install the lockset according to the opening direction of your door.
Secure lockset with provided G screws.
Measure the distance between center of front door
hole to the edge of your door. Push the shaft (a) to
adjust the lockset to 2-3/8"(60mm) or 2-3/4"(70mm).
2-3/8"
(60mm)
2-3/4"
(70mm)
(a)
OR
In-swing Door Out-swing Door
6
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
R
The lock ships set for right swing doors. Skip STEP 2 if your door is a right swing door.
See steps below to change door handle orientation for a left swing door.
Determine right swing or left swing door
While facing the door from the inside, if hinges are on the right side you have the right swinging
door. If hinges on the left side you have a left swinging door.
Changing the Exterior Handle Orientation
(Right handle)
12 3
Insert key and rotate lock
face so that the two white
dots align as shown.
Use the provided pin insert R
to push the metal pin located
at the 3 o’clock of the the base
handle, then the other pin at 9
o’clock position. Remove the
handle once the pins are
compressed.
Rotate the handle 180oto the
other side of the lock.
Using your fingers, press the
two pins located on the left
and right side of the the lock
to insert the handle back onto
the lock.
7
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
Check that your handle works
smoothly by giving it a turn up
and down.
Twist key back to horizontal position. The key can
be taken out once it goes back to the horizontal
position.
45
6
Confirm that your installation was
complete by checking if the pins
are flush against the handle, and
has popped out. Adjust the handle
accordingly to make sure the pins
are fully decompressed and sits
flush against the surface.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
8
Step 2
continued
Remove the screw by turning counter
clockwise and rotate the handle 180°
in the direction of the arrow as shown.
Make sure the screw hole is aligned with
the marker as illustrated.
Changing the Interior Handle Orientation
Securely screw clockwise as shown
to complete your handle orientation
change.
12
9
PREPARING LOCK FOR INSTALLATION
Step 3
2
D
If you drilled a hole in Preparation, use Slotted Barrel Extension Uand securely tighten with a flat head
screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave
this pole removed.
1
Install Spindle Cwith
the holes side into the
base of the lock and
align the holes locate
in the 3 o’clock and
9 o’clock position.
Insert locking pin D
in to the hole as
shown above.
4Peel paper layer OFF the
Adhesive tape and prepare
for installation.
3
Carefully bend the end
of the locking pin D with
a needle nose pliers.
Failure to bend the locking
pin and turn the handle
freely without obstruction
will result to malfunction.
Altri manuali per SECURE PRO
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Lockly Serratura della porta
Lockly
Lockly LATCH EDITION SECURE PGD628 Manuale utente
Lockly
Lockly DEADBOLT EDITION 7S Manuale utente
Lockly
Lockly LUX COMPACT PGD688FSN Manuale utente
Lockly
Lockly DEADBOLT SECURE PLUS Manuale utente
Lockly
Lockly LATCH EDITION 6S Manuale utente
Lockly
Lockly MORTISE EDITION SECURE LUX PGD829AFUS Manuale utente
Lockly
Lockly DEADBOLT EDITION SECURE PGD728 Manuale utente
Lockly
Lockly LATCH EDITION SECURE PGD628 Manuale utente
Lockly
Lockly PRO Manuale utente
Lockly
Lockly LUX Compact Manuale utente
Lockly
Lockly DEADBOLT EDITION 7S Manuale utente
Lockly
Lockly LATCH EDITION SECURE PGD628 Manuale utente
Lockly
Lockly Secure LUX Manuale utente
Lockly
Lockly SECURE PLUS Manuale utente
Lockly
Lockly LATCH EDITION SECURE PLUS Manuale utente
Lockly
Lockly Satin Nickel Secure Plus Smart Lock Deadbols Manuale utente
Lockly
Lockly DEADBOLT EDITION PGD1128FPW Manuale utente
Lockly
Lockly FLEX TOUCH PRO Manuale utente
Lockly
Lockly PGD728F Manuale utente
Lockly
Lockly VISION ELITE Manuale di istruzioni
