Lodar 92 Series Manuale utente

or Disconnect Battery

IDENTIFY POWER

CONNECTION POINT

AND ISOLATE SUPPLY

Fuse

Remove fuse

Vehicle batteries contain gasses

which are flammable and explosive.

Wear eye protection and do not lean

over battery while disconnecting. Do

!WARNING

92220.02E

1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps

through one output or 5 Amps each through 3 outputs.

2. Master Output. This can be configured to Continuous or Parallel operation, see below right

for more details.

3. If Receiver outputs are connected in parallel with an external switching device (wired remote)

the Receiver will instantly switch off when the wired remote is operated

4. Lodar Receivers have an isolation switch for safety, to allow for registering a MUST

replacement Transmitter.

5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of

inactivity. This can be altered, ask your dealer.

1!BEFORE YOU START

Wiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers.

Secure using 5mm (3/16") bolts (not supplied)

through the 4 mounting feet

TAKE TIME TO LOCATE THE BEST POSITION

If necessary, power the Receiver and move it around

the vehicle until the required performance is achieved.

Operate the Transmitter and observe the Receiver

internal LED’s.

Mount as HIGH as possible

AVOID surfaces with HEAVY VIBRATION

AVOID DIRECT SPRAY from wheels

In a HOT CLIMATE fit in a SHADED position

Cable gland should face DOWN or BACK

Receiver 92 20 RX and 93 20 RX shown,

CAUTION

MOUNT RECEIVER

!What is the MASTER Output for ?

It is used to operate the pump of an

electro-hydraulic power pack or

maybe a clutch pump. It can also be

used for powering a dump valve,

master valve etc.

It can be configured to work

continuously, that is ON when SET

is pressed and OFF when STOP is

pressed;

or in

parallel with any output, that is, it is

active only a function is operated.

If it is needed with certain functions

only, this can easily be configured.

CONNECTION DETAIL

OPTIONAL AERIAL

CONNECTION

ENSURE THAT THE GAUGE

OF WIRE USED CAN CARRY

15 AMPS (THIS IS THE

MAXIMUM TOTAL CURRENT

THAT LODAR CAN SWITCH)

OVER THE DISTANCE FROM

THE BATTERY WITH NO

SIGNIFICANT VOLTS DROP!

IMPORTANT

The Receiver switches itself off

after 30 minutes of inactivity.

SAFETY FEATURE

!NOTE

The STOP input can be

used for OVERLOAD or

OVER-TEMPERATURE

etc. If the chassis is

GROUND, then a return

wire is not required.

IMPORTANT

TAKE CARE NOT TO SHORT

OUT THE MOSFET’s WHEN

MAKING CONNECTIONS

GROUND

12 / 24 VOLT

COMMON

FUNCTION 5

FUNCTION 6

FUNCTION 7

FUNCTION 8

MASTER

FUNCTION 1

FUNCTION 2

LK1

FUNCTION 3

FUNCTION 4

Make connections as detailed below

and record wire colours in the boxes

LK2

LK1, when bridged causes the Master Output to be Parallel

LK2, when bridged causes the Master Output to be Continuous

JUMPER MUST BE FITTED FOR LODAR TO WORK

POWER DOWN RECEIVER BEFORE MAKING CHANGES

JUMPER may be or RED BLUE

STOP

Connections

S+ (Safety

Solenoid etc.)

L1 = LIMIT 1

L2 = LIMIT 2

LIMIT INPUTS

FUNCTION 9

FUNCTION 10

FUNCTION 15

FUNCTION 16

FUNCTION 17

FUNCTION 18

FUNCTION 11

FUNCTION 12

FUNCTION 13

FUNCTION 14

FUNCTION 19

FUNCTION 20

STOP

0 Volts

GROUND

7FINAL CHECK

!ALL ITEMS

IMPORTANT

Check all

connector

screws for

tightness

even the ones

that are not

used as these

could cause a

short circuit

if they vibrate

out of the

connector

Check locknut

Check gland

Check tightness of cable gland

Stray strands of wire can

cause a short circuit

cdCONNECTOR

BLOCK



secure wire

or Connect Battery

IT IS NOW SAFE TO RECONNECT THE POWER SUPPLY

Refit fuse

eFuse

Vehicle batteries contain gasses

w h i c h a r e f l a m mabl e a n d

explosive. Wear eye protection

and do not lean over battery while

!WARNING

SPECIAL

ORDER

ONLY

Indicator LED’s 1 through 20

Indicator LED - Master 5 Volts LED

Set LED

Fault LED

LED’s indicate the following

LED marked “5V” indicates

power supply for control circuits

is OK

LED marked “SET” indicates the

system active.

LED marked “Fault” indicates an

overload is present; the system

cannot be reset until overload is

removed.

This LED blinks for 20 seconds

when the system is initially

powered. A replacement

Transmitter (or Keypad or Wired

Remote) has to be registered

during this 20 second period.

LED’s marked F1 to F16 and M

(and optional MC) when ON

indicate an output to that function

(MC is an extra Continuous

Master output)

COMPONENT DETAIL

Lodar 9100 Series is guaranteed for a period of 24

months from the date of purchase, as long as it is

wired in accordance with our instructions, and that

the equipment is fitted with an isolation system to

shut off all power in event of an emergency.

Your product is marked with this symbol. It means

that used electrical and electronic products should

not be mixed with general household waste. There is

a separate collection system for these products.

In the EEC - Please contact your National Distributor

(see www.lodar.com for this information) who will

inform you about the take-back of the product. You

might be charged for the costs arising from the take-

back and recycling. Small products might be taken

back by your local collection facilities.

Outside the EEC - If you wish to discard this product

please contact your local authorities and ask for the

correct method of disposal

IPIP

F1 F2

F3 F4

F5 F6

F7 F8

F9 F10

F11 F12

F13 F14

F15 F16

F17 F18

F19 F20

Numbering convention

of Transmitter Keypad

showing the Receiver

output function number

for that key.

LIMITS - What are these?

The new compact 20

function Receiver has an

input for limit functions.

The circuits between L1 and

ground (-) or L2 and ground,

which when the circuit is

made, or broken, will allow

a function to start or cause

a function to stop.

This requires special

programming.

We also have available an

add-on PCB, Part No. 9220

that has a further 8 Limits.

We have successfully used

this feature on a number of

projects to introduce a

degree of logic using the

on board Programmable IC

or PIC. It may not be

economical to program the

Receiver PIC for a small

batch, please ask.

To register ONE Transmitter to a Receiver.

1. Switch OFF or DISCONNECT the power to the Receiver.

2. Switch ON or Reconnect the power to the Receiver.

This opens a 20 second registration window in the Receiver processor.

If you are looking at the Receiver PCB the Fault LED Flashes.

3. Immediately PRESS and HOLD the Reset Button Transmitter (Indicated)

then within 2 seconds PRESS and HOLD F1, continue to hold BOTH BUTTONS

for a minimum of 5 seconds during this 20 second window.

When the Transmitter is Registered the Fault LED will be illuminated for 3 seconds.

I you are registering TWO Transmitters then within this 3 seconds period release both buttons

and when the Fault LED starts to flash again.

3a. Immediately PRESS and HOLD the Reset Button on the second Transmitter (Indicated) then within 2 seconds

PRESS and HOLD F1, continue to hold BOTH BUTTONS for a minimum of 5 seconds or until the SET LED

illuminates.

Both your Transmitters should now operating the Receiver.

THIS WORKS FOR ALL TRANSMITTERS WITH A AND A BUTTONSTOP RESET

If you have any problems please phone either your local Distributor or Lodar directly

In the UK +44 1922 613633. In the US please phone 1-877- 257-1581.

STX-A4.02

1 2

Function Buttons

RESET Button activates the

Receiver and the keypad

function buttons

4 Release Screws for

Battery Compartment

at rear.

4 x AAA batteries

Effective working range up to a distance of

60 metres (200 feet) 92 Series and

300 metres (1000ft) 93 Series.

STOP Button switches off

the Receiver and the keypad

function buttons

L.E.D.

Blinks when Transmitter

and Receiver are active.

ON when a Transmitter

Button is pressed.

Pulses while transmitting

when battery is low.

The Transmitter automatically

transmits a STOP signal after

30 minutes; this de-activates

the Receiver and the Transmitter

keypad.

SAFETY FEATURE

92/93 Series IP Transmitter (16 Function shown )

PRESS & HOLD

RESET & THEN

F1 WITHIN

2 SECONDS

Questo manuale è adatto per i seguenti modelli

Altri manuali Lodar Ricevitore

Lodar

Lodar 92 Series Manuale utente

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente