Logic Controls LD9000 Series Manuale utente

Customer Displays

2 by 20 character display

USER MANUAL

Models: LD9000 Series

NOTICE

The manufacturer of the POS pole display makes no

representations or warranties, either expressed or implied, by

or with respect to anything in this manual, and shall not be

liable for any implied warranties of fitness for a particular

purpose or for any indirect, special or consequential

damages. Information in this document is subject to change

without notice and does not represent a commitment on the

part of the manufacturer.

FCC NOTICE

This equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in accordance

with this manual, may cause interference to radio

communications. It has been tested and found to comply with

the limits for a ClassA digital device pursuant to Subpart J of

Part 15 of FCC Rules, which are designed to provide

reasonable protection against interference when operated in

a commercial environment. Operation of this equipment in a

residential area is likely to cause interference in which case

the user at his own expense will be required to take whatever

measures may be required to correct the interference.

LOGIC CONTROLS, INC.

355 Denton Avenue

New Hyde Park, NY 11040

TEL: (516) 248-0400

FAX: (516) 248-0443

Email: [email protected]

http://www.logiccontrols.com

iii

TABLE OF CONTENTS

FEATURES.....................................................................................1

MODEL IDENTIFICATION............................................................2

CARTON CONTENTS...................................................................2

INSTALLATION..............................................................................3

FUNCTIONAL TEST......................................................................5

INTERFACE CONNECTION........................................................8

SOFTWARE COMMANDS........................................................10

HARDWARE CONFIGURATION..............................................11

DISPLAY CHARACTER CODES.............................................12

GENERAL SPECIFICATIONS..................................................13

FEATURES

The LD9000 family of pole displays offers a wide range of high quality

features and models to choice from. Listed below are the features

incorporated into each pole display. Not all features are available in all

models. The model identification chart will assist you in selecting the

model best suited to your needs.

Features - All Models

•Bright blue-green fluorescent display

•Large 9mm character height

•Double sided display available

•Supports high speed serial protocol: up to 19,200 baud rate, 1 stop

bit

•Automatic message scrolling

•Two line display with 20 characters per line

•Matched optical lens for better viewing contrast

•Ergonomic design

•Direct RS232C or parallel interface

•Long life and trouble free operation

•Five adjustable viewing angles

•Simple installation

•Available with 120V or 220V Power Adapters

Features - Model dependent

•Emulation of other popular command sets

•Double sided display

•User definable character

•Parallel pass-thru

•True RS232C pass-thru

•Real time clock

•One time message scrolling

•Ability to disable attention code

•Ability to change attention code

MODEL IDENTIFICATION

LD9 __ __ __ - __ __

X = Double Sided Display

PT = Pass Thru

25 = DB25F connector to computer

POWER ADAPTER

0 = 120VAC*

COMMAND SET 1 = 220VAC

0 = LOGIC CONTROLS*

1 = LOGIC CONTROLS SERIAL/PARALLEL INTERFACE

WITH PASS-THRU 0 = SERIAL 9600 BAUD*

2 = SPECIAL COMMAND SET 1 (Aedex emulation) 1 = SERIAL 600 BAUD

3 = SEPCIAL COMMAND SET 2 (Noritaki emulation) 2 = SERIAL 1200 BAUD

4 = SPECIAL COMMAND SET 3 (Epson D202 emulation) 3 = SERIAL 2400BAUD

5 = SPECIAL COMMAND SET 4 (Ultimate PD1100XL/XLT) 4 = SERIAL 4800 BAUD

9 = OPOS COMMAND SET 5 = SERIAL 19200 BAUD

9 = PARALLEL INTERFACE

* Default Values

** Call for description of Command Sets

CARTON CONTENTS

1. Pole display, pre-assembled.

2. Interface cable, comes with a DB9F connector (to computer) and a

Mini DIN8F connector (to pole display) as standard equipment.

Optional DB25F connector (to computer) is available.

Note: This cable is only supplied with standard serial pole displays

with no pass-thru function. Other interface options will have

different cables.

3. Transformer adapter 120VAC to 7.5VAC (optional 220VAC).

4. Metal base plate with mounting hardware.

5. Quick Installation Guide.

INSTALLATION

Your LD9000 family of pole displays has been pre-assembled to make

the installation as simple as possible.

Serial Interface Non-pass-thru Models Installation

1. Mount the pole display to the metal base plate using the

mounting hardware provided.

2. The pole display can be used in a freestanding mode or

attached to the counter using the remaining mounting

hardware.

3. Connect the round Mini DIN8M connector from the pole display

to the round Mini DIN8F connector of the interface cable.

4. Connect the DB9F connector to the computer’s serial COM1 or

COM2 port.

5. Connect the female phone jack of the power adapter to the

male phone jack of the interface cable.

6. Plug the power adapter into a 120VAC outlet.

7. A start up text message (LOGIC CONTROLS POS

COMPONENTS) will be present for a short time. When this

message disappears the cursor will be displayed at the left-

most digit of the top row.

Parallel Interface Non-pass-thru Models Installation

1. Mount the pole display to the metal base plate using the

mounting hardware provided.

2. The pole display can be used in a freestanding mode or

attached to the counter using the remaining mounting

hardware.

3. Connect the DB25M connector to the computer’s parallel

printer port (LPT1).

4. Connect the female phone jack of the power adapter to the

male phone jack of the pole display cable.

5. Plug the power adapter into a 120VAC outlet.

6. A start up text message (LOGIC CONTROLS POS

COMPONENTS) will be present for a short time. When this

message disappears the cursor will be displayed at the left-

most digit of the top row.

Serial Interface Pass-thru Models Installation

1Mount the pole display to the metal base plate using the

mounting hardware provided.

2The pole display can be used in a freestanding mode or

attached to the counter using the remaining mounting

hardware.

3Connect the DB25M connector to the peripheral device or a

serial pass-thru terminator (optional accessory). Turn on power

of the peripheral device.

4Connect the DB9F connector to the computer’s serial COM1 or

COM2 port.

5Connect the female phone jack of the power adapter to the

male phone jack of the pole display cable.

6Plug the power adapter into a 120VAC outlet.

7A start up text message (LOGIC CONTROLS POS

COMPONENTS) will be present for a short time. When this

message disappears the cursor will be displayed at the left-

most digit of the top row.

Parallel Interface Pass-thru Models Installation

1Mount the pole display to the metal base plate using the

mounting hardware provided.

2The pole display can be used in a freestanding mode or

attached to the counter using the remaining mounting

hardware.

3Connect the DB25F connector to the peripheral device or

parallel pass-thru terminator (optional accessory). Turn on

power of the peripheral device.

4Connect the DB25M connector to the computer’s parallel

printer port (LPT1).

5Connect the female phone jack of the power adapter to the

male phone jack at the DB25M/DB25F connector.

6Plug the power adapter into a 120VAC outlet.

7A start up text message (LOGIC CONTROLS POS

COMPONENTS) will be present for a short time. When this

message disappears the cursor will be displayed at the left-

most digit of the top row.

FUNCTIONAL TEST

The following test sequence will verify that your pole display is

working properly. Before you start this procedure, you must install the

pole display correctly as outlined under the INSTALLATION section.

The functional test should be done under MSDOS command prompt

by booting up the computer in DOS mode, or shell out to DOS prompt

(in window95/98/ME) or COMMAND prompt (in windows NT/2000).

For double sided displays, the messages will be shown on both sides

at the same time.

NOTE: The actual key entries in the text below are enclosed within quotation

marks ( “ ” ). Do not type the quotation marks as part of your entries.

Serial Interface Pole Displays Functional Test

This test procedure assumes the pole display is connected to COM1

of the computer. If COM2 is being used, type COM2 where COM1 is

called out.

Close all opened application programs that use the same COM port

before going into DOS command prompt. Enter the following

command lines to open the COM port for communication with the pole

display:

Type “MODE COM1 96,N,8,1” and press the ENTER key.

Type “TYPE CON>COM1” and press the ENTER key.

LD9000, LD9300, LD9400, LD9500 and LD9900

1. Type “ABCDEFGH” and press ENTER key. The display will show

“ABCDEFGH” on the first line.

2. To end the test press Ctrl-C (hold down Ctrl and press C).

LD9200

1. Type “!#1ABCDEFGH” and press ENTER key. The display will

show “ABCDEFGH” on the first line.

2. To end the test press Ctrl-C (hold down Ctrl and press C).

LD9100-PT, LD9300-PT, LD9400-PT and LD9900-PT

1. Type “ABCDEFGH” and press ENTER key. The display will show

“ABCDEFGH” on the first line.

2. Type “^APASSTHRU” (^A is entered as Ctrl-A ) and press ENTER

key. The data will be passed through to the peripheral (e.g. a

printer). These characters are not shown on the display.

3. Type “!#^BNUMBER12345” (^B is entered as Ctrl-B), then press

ENTER key. The display will show “NUMBER12345” on the first

line.

4. To end the test press Ctrl-C (hold down Ctrl and press C).

LD9200-PT

1. Type “!#1ABCDEFGH” and press ENTER key. The display will

show “ABCDEFGH” on the first line.

2. Type “PASSTHRU” and press ENTER key. The data will be

passed through to the peripheral (e.g. a printer). These characters

are not shown on the display.

3. Type “!#1NUMBER12345”, then press ENTER key. The display

will show “NUMBER12345” on the first line.

4. To end the test press Ctrl-C (hold down Ctrl and press C).

Parallel Interface Pole Displays Functional Test

This procedure assumes the pole display is connected to the LPT1

port of the computer. If parallel port LPT2 is being used, type LPT2

where LPT1 is called out.

LD9090, LD9390, LD9490, LD9590 and LD9990

1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. The

display will show “ABCDEFGH” on the first line.

LD9290

1. Type “ECHO !#1ABCEDFGH>LPT1” and press ENTER key. The

display will show “ABCDEFGH” on the first line.

LD9190-PT, LD9390-PT, LD9490-PT and LD9990-PT

1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. The

display will show “ABCDEFGH” on the first line.

2. Type “ECHO ^APASSTHRU>LPT1” (^A is entered as Ctrl-A) and

press ENTER key. The data will be passed through to the

peripheral (e.g. a printer). These characters are not shown on the

display.

3. Type “ECHO !#^BNUMBER12345>LPT1” (^B is entered as Ctrl-

B), then press ENTER key. The display will show

“NUMBER12345” on the first line.

LD9290-PT

1. Type “ECHO !#1ABCEDFGH>LPT1” and press ENTER key. The

display will show “ABCDEFGH” on the first line.

2. Type “ECHO PASSTHRU>LPT1” and press ENTER key. The

data will be passed through to the peripheral (e.g. a printer).

These characters are not shown on the display.

3. Type “ECHO !#1NUMBER12345>LPT1”, then press ENTER key.

The display will show “NUMBER12345” on the first line.

For further testing of OPOS displays (LD9900 and LD9990), follow the

instructions in the readme.doc file after software installation.

Altri manuali per LD9000 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Logic Controls Monitor

Logic Controls

Logic Controls LE1000 Manuale utente

Logic Controls

Logic Controls LE1015 Manuale utente

Logic Controls

Logic Controls LD9000 Series Manuale utente

Logic Controls

Logic Controls TD3000 Series Manuale utente

Logic Controls

Logic Controls LT9000 Series Manuale utente

Logic Controls

Logic Controls PD6000 Manuale utente

Logic Controls

Logic Controls PD3000 Series Manuale utente

Logic Controls

Logic Controls PDX3 Series Manuale utente

Logic Controls

Logic Controls LE1017 Series Manuale utente

Logic Controls

Logic Controls TD3000 Series Manuale utente

Logic Controls

Logic Controls PD3000 Series Manuale utente

Logic Controls

Logic Controls LT9000 Series Manuale utente

Logic Controls

Logic Controls TD3000 Series Manuale utente

Logic Controls

Logic Controls LD9000 Series Manuale utente

Logic Controls

Logic Controls PD3000 Series Manuale utente

Logic Controls

Logic Controls LE1017 Series Manuale utente

Logic Controls

Logic Controls LT9000 Series Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione