Logic Controls LT9000 Series Manuale utente
i
Table Displays
2 by 20 character display
USER MANUAL
Models: LT9000 Series
ii
NOTICE
The manufacturer of the POS table display makes no
representations or warranties, either expressed or implied, by
or with respect to anything in this manual, and shall not be
liable for any implied warranties of fitness for a particular
purpose or for any indirect, special or consequential
damages. Information in this document is subject to change
without notice and does not represent a commitment on the
part of the manufacturer.
FCC NOTICE
This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance
with this manual, may cause interference to radio
communications. It has been tested and found to comply with
the limits for a Class A digital device pursuant to Subpart J of
Part 15 of FCC Rules, which are designed to provide
reasonable protection against interference when operated in
a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever
measures may be required to correct the interference.
LOGIC CONTROLS, INC.
355 Denton Avenue
New Hyde Park, NY 11040
TEL: (516) 248-0400
FAX: (516) 248-0443
Email: [email protected]
http://www.logiccontrols.com
iii
TABLE OF CONTENTS
FEATURES.....................................................................................1
MODEL IDENTIFICATION............................................................2
CARTON CONTENTS...................................................................2
INSTALLATION..............................................................................3
FUNCTIONAL TEST......................................................................5
INTERFACE CONNECTION........................................................8
SOFTWARE COMMANDS........................................................10
HARDWARE CONFIGURATION..............................................11
DISPLAY CHARACTER CODES.............................................12
GENERAL SPECIFICATIONS..................................................13
1
FEATURES
The LT9000 family of table displays offers a wide range of high quality
features and models to choice from. Listed below are the features
incorporated into each table display. Not all features are available in
all models. The model identification chart will assist you in selecting
the model best suited to your needs.
The LT9000 family has the industry standard 9.5mm high vacuum
fluorescent 5x7 pixel display.
Features - All Models
•Bright blue-green fluorescent display
•Large 9.5mm character height
•Supports high speed serial protocol: up to 19,200 baud rate, 1 stop
bit
•Automatic message scrolling
•Two line display with 20 characters per line
•Matched optical lens for better viewing contrast
•Ergonomic design
•Direct RS232C interface
•Long life and trouble free operation
•Simple installation
•Available with 120V or 220V Power Adapters
Features - Model dependent
•Emulation of other popular command sets
•User definable character
•True RS232C pass-thru
•Real time clock
•One time message scrolling
•Ability to disable attention code
•Ability to change attention code
2
MODEL IDENTIFICATION
LT9 __ __ __ - __ __
Blank = No Pass Thru
PT = Pass Thru
25 = DB25F connector to computer
POWER ADAPTER
0 = 120VAC*
COMMAND SET 1 = 220VAC
0 = LOGIC CONTROLS*
1 = LOGIC CONTROLS SERIAL/PARALLEL INTERFACE
WITH PASS-THRU 0 = SERIAL 9600 BAUD*
2 = SPECIAL COMMAND SET 1 (Aedex emulation) 1 = SERIAL 600 BAUD
3 = SEPCIAL COMMAND SET 2 (Noritaki emulation) 2 = SERIAL 1200 BAUD
4 = SPECIAL COMMAND SET 3 (Epson D202 emulation) 3 = SERIAL 2400 BAUD
5 = SPECIAL COMMAND SET 4 (Ultimate PD1100XL/XLT) 4 = SERIAL 4800 BAUD
9 = OPOS COMMAND SET 5 = SERIAL 19200 BAUD
* Default Values
** Call for description of Command Sets
CARTON CONTENTS
1. Table display, pre-assembled.
2. Interface cable, comes with a DB9F connector (to computer) and a
DB9M connector (to table display) as standard equipment.
Optional DB25F connector (to computer) is available.
Note: This cable is only supplied with standard serial table
displays with no pass-thru function. Other interface options
will have different cables.
3. Transformer adapter 120VAC to 7.5VAC (optional 220VAC).
4. Quick Installation Guide.
3
INSTALLATION
Your LT9000 family of table displays has been pre-assembled to
make the installation as simple as possible.
Serial Interface Non-pass-thru Models Installation
1. The table display can be used in a freestanding mode or
mounted to the counter with the two holes at the rear of the
unit.
2. Connect the DB9M connector of the interface cable to the table
display.
3. Connect the DB9F connector to the computer’s serial COM1 or
COM2 port.
4. Connect the female phone jack of the power adapter to the
male phone jack of the interface cable.
5. Plug the power adapter into a 120VAC outlet.
6. A start up text message (LOGIC CONTROLS POS
COMPONENTS) will be present for a short time. When this
message disappears the cursor will be displayed at the left-
most digit of the top row.
Serial Interface Pass-thru Models Installation
1. The table display can be used in a freestanding mode or
mounted to the counter with the two holes at the rear of the
unit.
2. Connect the DB9M connector of the interface cable to the table
display.
3. Connect the DB25M connector to the peripheral device or a
serial pass-thru terminator (optional accessory). Turn on power
of the peripheral device.
4. Connect the female phone jack of the power adapter to the
male phone jack of the table display cable.
5. Connect the DB9F connector to the computer’s serial COM1 or
COM2 port.
6. Plug the power adapter into a 120VAC outlet.
7. A start up text message (LOGIC CONTROLS POS
COMPONENTS) will be present for a short time. When this
message disappears the cursor will be displayed at the left-
most digit of the top row.
4
Parallel Interface Non-pass-thru Models Installation
1. The table display can be used in a freestanding mode or
mounted to the counter with the two holes at the rear of the
unit.
2. Connect the DB25F connector of the interface cable to the
table display.
3. Connect the DB25M connector to the computer’s parallel
printer port (LPT1).
4. Connect the female phone jack of the power adapter to the
male phone jack of the table display cable.
5. Plug the power adapter into a 120VAC outlet.
6. A start up text message (LOGIC CONTROLS POS
COMPONENTS) will be present for a short time. When this
message disappears the cursor will be displayed at the left-
most digit of the top row.
Parallel Interface Pass-thru Models Installation
1The table display can be used in a freestanding mode or
mounted to the counter with the two holes at the rear of the
unit.
2Connect the DB25F connector of the interface cable to the
table display.
3Connect the DB25F side on the DB25M/25F connector to the
peripheral device or parallel pass-thru terminator (optional
accessory). Turn on power of the peripheral device.
4Connect the DB25M side on the DB25M/25F connector to the
computer’s parallel printer port (LPT1).
5Connect the female phone jack of the power adapter to the
male phone jack at the DB25M/25F connector.
6Plug the power adapter into a 120VAC outlet.
7A start up text message (LOGIC CONTROLS POS
COMPONENTS) will be present for a short time. When this
message disappears the cursor will be displayed at the left-
most digit of the top row.
5
FUNCTIONAL TEST
The following test sequence will verify that your table display is
working properly. Before you start this procedure, you must install the
table display correctly as outlined under the INSTALLATION section.
The functional test should be done under MSDOS command prompt
by booting up the computer in DOS mode, or shell out to DOS prompt
(in window95/98/ME) or COMMAND prompt (in windows NT/2000).
NOTE: The actual key entries in the text below are enclosed within quotation
marks ( “ ” ). Do not type the quotation marks as part of your entries.
Serial Interface Table Displays Functional Test
This test procedure assumes the table display is connected to COM1
of the computer. If COM2 is being used, type COM2 where COM1 is
called out.
Close all opened application programs that use the same COM port
before going into DOS command prompt. Enter the following
command lines to open the COM port for communication with the
table display:
Type “MODE COM1 96,N,8,1” and press the ENTER key.
LT9000, LT9300, TPD3400, LT9500 and LT9900
1. Type “Echo ABCDEFGH>COM1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
LT9200
1. Type “Echo !#1ABCDEFGH>COM1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
6
LT9100-PT, LT9300-PT, LT9400-PT and LT9500-PT
1. Type “Echo ABCDEFGH>COM1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
2. Type “Echo ^APASSTHRU>COM1” ( ^A is entered as Ctrl-A ) and
press ENTER key. The data will be passed through to the
peripheral (e.g. a printer). These characters are not shown on the
display.
3. Type “Echo !#^BNUMBER12345>COM1”, (^B is entered as Ctrl-
B) then press ENTER key. The display will show “NUMBER12345”
on the first line.
LT9200-PT
1. Type “Echo !#1ABCDEFGH>COM1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
2. Type “Echo PASSTHRU>COM1” and press ENTER key. The data
will be passed through to the peripheral (e.g. a printer). These
characters are not shown on the display.
3. Type “Echo !#1NUMBER12345>COM1”, then press ENTER key.
The display will show “NUMBER12345” on the first line.
Parallel Interface Table Displays Functional Test
This procedure assumes the table display is connected to the LPT1
port of the computer. If parallel port LPT2 is being used, type LPT2
where LPT1 is called out.
LT9090, LT9390, LT9490, LT9590 and LT9990
1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
LT9290
1. Type “ECHO !#1ABCEDFGH>LPT1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
7
LT9190-PT, LT9390-PT, LT9490-PT and LT9590-PT
1. Type “ECHO ABCDEFGH>LPT1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
2. Type “ECHO ^APASSTHRU>LPT1” (^A is entered as Ctrl-A) and
press ENTER key. The data will be passed through to the
peripheral (e.g. a printer). These characters are not shown on the
display.
3. Type “ECHO !#^BNUMBER12345>LPT1” (^B is entered as Ctrl-
B), then press ENTER key. The display will show
“NUMBER12345” on the first line.
LT9290-PT
1. Type “ECHO !#1ABCEDFGH>LPT1” and press ENTER key. The
display will show “ABCDEFGH” on the first line.
2. Type “ECHO PASSTHRU>LPT1” and press ENTER key. The data
will be passed through to the peripheral (e.g. a printer). These
characters are not shown on the display.
3. Type “ECHO !#1NUMBER12345>LPT1”, then press ENTER key.
The display will show “NUMBER12345” on the first line.
For further testing of OPOS displays (LT9900), follow the instructions
in the readme.doc file after software installation.
Altri manuali per LT9000 Series
2
Questo manuale è adatto per i seguenti modelli
20
Indice
Altri manuali Logic Controls Monitor
Logic Controls
Logic Controls LE1015 Manuale utente
Logic Controls
Logic Controls PD3000 Series Manuale utente
Logic Controls
Logic Controls PDX3 Series Manuale utente
Logic Controls
Logic Controls PD3000 Series Manuale utente
Logic Controls
Logic Controls LT9000 Series Manuale utente
Logic Controls
Logic Controls TD3000 Series Manuale utente
Logic Controls
Logic Controls LT9000 Series Manuale utente
Logic Controls
Logic Controls LD9000 Series Manuale utente
Logic Controls
Logic Controls PD3000 Series Manuale utente
Logic Controls
Logic Controls TD3000 Series Manuale utente
Logic Controls
Logic Controls LE1000 Manuale utente
Logic Controls
Logic Controls PD6000 Manuale utente
Logic Controls
Logic Controls LE1017 Series Manuale utente
Logic Controls
Logic Controls LE1017 Series Manuale utente
Logic Controls
Logic Controls LD9000 Series Manuale utente
Logic Controls
Logic Controls TD3000 Series Manuale utente
Logic Controls
Logic Controls LD9000 Series Manuale utente
