Look Solutions Radio Remote Manuale utente

Operating manual

Radio Remote

v 2.0

aLook Solutions product

Set of Equipment supplied

–1receiver with mini-stereo-jack-plug or 3-pin-XLR-plug

–1radio transmitter

Please check whether all the products you ordered are supplied.

Contents

1. Introduction 4

2. The Transmitter

2.1 Operation 5

2.2 Coding 6

2.3 Replacing the battery 6

3. The Receiver

3.1 Operation 7

3.2 Configuring the buttons 8

3.2.1 In general 8

3.2.2 Configure the buttons in the Standard-Mode 9

3.2.3 Configure the buttons in the On / Off-Mode 10

3.3 Delete the configuration 11

3.4 Wiring of the connectors 11

4. System range 12

5. Technical Data 13

6. Warranty Conditions 14

1. Introduction

The UHF radio system consists of a radio transmitter and one or several receivers.

The operating frequency of the system is 433.92 MHz.

The radio remote has two different Modes, which can be changed easily

whenever neccessary (see point 3.2.3):

In the Standard-Mode “Press and release“ the machine will be triggered to run

as long as the button is held down. If the button is released, the machine will

stop working.

In the “On / Off“-Mode, the machine will be activated by pressing the pro-

grammed Start-button shortly and deactivated by pressing the programmed Stop-

button.

The radio transmitter allows you to address four channels which can either be

four individual receivers or four receiving groups. The number of the receivers

per channel is not limited.

One receiver can save up to six configurations. The “On“- and “Off“-buttons

can be also configurated.

Thus, the permanent pressing of the button at the transmitter is no longer

neccessary. The machine can now be activated by pressing button 1 briefly and

can be deactivated by pressing button 3, depending on which buttons have been

configured.

The transmitter of the original Look radio remote is compatible with the new

receivers.

The receiver of the original is incompatible with the new transmitter!

The transmitter is supplied with the first button pre-programmed, allowing

the radio remote to be used immediately.

2. The Transmitter

2.1 Operation

The radio transmitter is supplied in a usable state with the battery already

installed.

To transmit press one of the four buttons (1, 2, 3 or 4). If the key is pressed too

briefly, the receiver ignores the command. For receiving several consecutive code

cycles must be received and identical before a command is recognized as valid.

While sending the signal, the transmitter should be in your hand and pointed

away from your body. If your hand cover the integrated antenna, or you approach

a large metal surface/area, the range may be reduced. This should therefore be

avoided.

The radio remote is supplied with the first button pre-programmed and the

connected machine will be activated by pressing this button, running as long as

the button is held down. Buttons two to four have no function yet.

The configuring and also the deleting of the configuring will be described in

chapter 3.1 to 3.3.

Button 1 Button 2

Button 3 Button 4

red LED

Screw

Transmitter front

2. The Transmitter

Code when delivered

(all switches with even figures in position “on“)

2.3 Replacing the battery

The transmitter can be coded individually. This can be helpful if several trans-

mitters with the same frequency (433.92 MHz) are being used in the same area.

The receiver will only react to the signal of the coded transmitter and cannot be

activated from a second transmitter.

Please note: The receiver will save the code of the transmitter and need not to

be coded itself.

All previous configurings of the buttons should be deleted, in advance, to enable

all buttons to work with the new code from the transmitter (see chapter 3.3).

The system offers 1024 coding options. The setting is made by means of DIP

switches. Each of the 10 switches has two operating positions: on and off.

When delivered the switches with even numbers are in position “on“.

To change the coding set by the factory, open the apparatus by loosening the

screw with a suitable screwdriver and dismantle the two halves of the casing.

Using a ball-point pen you can now set your individual code.

Please note: The coding of the smaller, 4-position DIP switch must never be

changed!

2.2 Coding

+–

1 2 3 4 5 6 7 8 9 10

The life of the battery depends on the use of the radio transmitter. If the range

is strongly reduced or transmission is not possible, the battery must be replaced.

Only use standard 12 V-alkaline batteries.

Loosen the screw with a suitable screwdriver and dismantle the two halves of

the casing. Remove the used-up battery and insert the new one. Pay attention to

polarity and test contact of the battery by trying to transmit.

3. The Receiver

3.1 Operation

Look

Solutions made in Germany

The receiver is equipped with a stereo jack plug [1] or a 3-pin-XLR-plug (it

depends on which machine it controls) and a short wire antenna [2].

Insert the plug [1] into the corresponding socket of the machine to gain control.

The receiver now has the neccessary power from the machine and is ready for

operation.

Pressing of button 1 of the radio transmitter now starts the fogging process.

Please note: The antenna should be in upright position and should not be

concealed by conductive objects.

3.2 Configuring the buttons

Due to the option to also configure “Off“-buttons, the radio remote has two

different modes:

In the Standard-Mode “Press and release“ the triggered machine runs as long

as the button is held down. If the button is released, the machine stops working.

In the “On / Off“-Mode, the triggered machine will be activated by pressing

the programmed Start-button briefly and deactivated by pressing the pro-

grammed Stop-button.

Thus, the permanent pressing of the button at the transmitter is no longer

neccessary. The machine can now be activated by pressing button one and can be

deactivated by pressing button 3, depending on which buttons have been

programmed.

The receiver can save up to six configurations.

Should several units be required to be addressed on the same or different

buttons (1,2, 3 or 4), the receiver has to be configured again.

The transmitter is supplied with the first button pre-programmed. Thus, the

radio remote can be used immediately.

3. The Receiver

3.2.1 In general

a) Open the receiver by removing the cover plate. This is only snapped together

and can usually be taken off without any tool. A slim slot screwdriver also

enables you to remove the cover.

b) Connect the receiver to the machine.

c) To start the configuration, press the black Configuration-button [1] briefly.

The yellow LED [2] flashes.

Press the button on the transmitter that shall be configured. If the configu-

ration is successful, the yellow LED [2] lights up permanently.

The connected machine will now run as long as the configured button at the

transmitter is held down.

The procedure can now be repeated if the configuration of further buttons is

required for the same receiver. Up to six buttons can be saved for one receiver. If

more then six buttons are configured, the previous configurations will be

overwritten.

You can configure several receivers on the same button. All receivers will then

be activated at the same time and for the same running period.

If the receivers should react on different buttons, repeat the above mentioned

procedure for each receiver, always configuring a different button at the trans-

mitter as the Start-button.

3.2.2 Configure the buttons in the Standard-Mode “Press and release“

The transmitter will be delivered with the first button pre-programmed as the

Start-button. The machine will run as long as this button is held down.

Please note: All pre-programmed configurations (button 1 = Start-button) should

be deleted (see point 3.3) before you start to configure the other buttons, unless

you want to use the first button as a Start-button.

Receiver as it looks in the Standard-Mode

(red Jumper in original position)

[1] black Configuration-button

[2] yellow LED

[3] red Jumper

3. The Receiver

3.2.3 Configure the buttons in the “On/Off“-Mode

3. The Receiver

a) Open the receiver by removing the cover plate. This is only snapped together

and can usually be taken off without any tool. A slim slot screwdriver also

enables you to remove the cover.

b) Remove the red Jumper [3]. To avoid the loss of the Jumper, replace it shifted

in a way, that one of the legs will stay uncovered as shown above.

c) Connect the receiver to the machine.

d) To start the configuration, press the black Configuration-button [1] briefly.

The yellow LED [2] flashes. Press the button at the transmitter that shall be

configured. If the configuration is successful, the yellow LED [2] lights up

permanently. The connected machine can now be deactivated with the

configured button.

The receiver changes into the On/Off-Mode by changing the position of the red

Jumper [3].

Those buttons already configured in the Standard-Mode will automatically be

recognized as Start-buttons. Buttons configured in the On/Off-Mode will be Stop-

buttons.

Therefore, the machine can be activated by pressing the configured Start-button

briefly. It is not neccessary to hold the button constantly. The configured Stop-

button can be pressed briefly to deactivate the machine.

Please note: The red Jumper [3] must be placed shifted for the On/Off-Mode to

remain activated. As soon as the red Jumper is replaced to its original position,

the Standard-Mode (Press and release) will automatically be re-activated!

This deactivates the configuration of the Stop-buttons but does not delete their

function. As soon as the Jumper is placed shifted again, the configured Stop-

buttons are reactivated.

Receiver as it looks in the „On / Off“-Mode

(Red Jumper shifted)

[1] black Configuration-button

[2] yellow LED

[3] red Jumper

Indice

Altri manuali Look Solutions Telecomando

Look Solutions

Look Solutions Radio remote V.5 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione