Louroe Electronics ASK-4 Manuale utente

Model AP-8

8 Zone Audio Base Station

2 Conductor shielded cable, 22

gauge with a 24 gauge drain wire

NOTE: Unshielded cable is not

satisfactory for audio systems

WIRING REQUIREMENTS

West Penn 452 or equivalent

The ASK-4® 108 is an eight zone audio monitoring system designed to interface with a DVR, VCR or other recording

device that accept line level audio. The AP-8 Audio Base Station has 8 microphone inputs, contains a built-in 3’ speaker

and volume control for producing live audio and playback. It has loop out RCA output per microphone so each

microphone can be recorded individually. It also has a selectable audio output that produces audio to a recorder for that

zone or microphone selected. The Verifact™ A microphones are omnidirectional pre-amplified microphone that produces

line level audio output.

AUDIO MONITORING SYSTEM

INSTALLATION AND OPERATING INSTRUCTIONS

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH: (818)994-6498 / FAX: (818)994-6458

/ www.louroe.com[email protected]

Page 1 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

ASK-4 #108

Contents Description

1 AP-8 listed Audio Base Station.

Used for listening to live audio

from microphone, as well as

audio playback from DVR’s, VCR’s

or other audio devices.

8 Verifact™ A Microphone listed Line Level, Electret condenser

microphone with preamp. Picks up

normal sounds within 30’ circle.

May be located Up to 1000’ from

AP-8 Base Station.

1 AD-1 listed AC ADAPTER.

Supplies 12 Vdc to AP-8 and

Microphone.

1 Dual RCA Cable RCA cable for connection to a

DVR/VCR or other Audio devices

that accept line level input

(0dB @ 600W).

Verifact™ A Microphones

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

DESCRIPTION AND FUNCTION OF PARTS

[1] - Play/Mute Switch Used when playing back audio from a recorder or mute the audio

from the microphone. No audio is heard on the Speaker[7] when

this switch is ON.

[2] - Zone Selector Switches Select zone for monitoring. Press switch of desired zone to listen

to live audio. Pressing more than one zone is possible when it is

necessary to monitor more than one zone at a time, but audio

may be difficult to understand if there is audio activity at several

zones. Zone switches light blue when press indicating active

zone.

[3] - Headset Jack Used for private listening. Any stereo headset with 8 to 600W

impedance maybe used. Mutes speaker output when use.

[4] - Power Indicator Lights (green) when power is turned ON.

[5] - Power-Volume Knob Rotating knob clockwise turns ON power to the unit as indicated

by the Power Indicator[4] light. Rotating further clockwise

increases the volume of the monitored audio as heard through

the Monitor Speaker[7].

Fig. 1 Front of AP-8

Fig. 1 Front view of AP-8

AP-2 and AP-4 have the

same features except

for the number of Zones

5432

INSTALLATION AND OPERATING INSTRUCTIONS

Page 3 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

Fig. 2 Rear view of AP-8

AP-2 and AP-4 have the

same features except

for the number of terminal

blocks and mic output

jacks for each zone

DESCRIPTION AND FUNCTION OF PARTS

[6] - Mic Input 3-Pin Terminal Block Connects to remote Louroe microphones.

[7] - Monitor Speaker Provides live audio through the 3” built-in speaker. Muted when

a headset is connected to Headset Jack[3].

[8] - Audio In Jack (RCA) Receives audio playback from DVR/VCR, etc. and is broadcast

through the built-in speaker. [7].

[9] - Audio Out Jack (RCA) Provides audio to DVR/VCR for recording or to other audio

devices accepting line level input when any of the Zone Selector

Switches[2] are activated or push in. The audio output to this

jack will be the audio selected by the Zone Selector Switches[2].

[10]- Power Jack Accepts 12Vdc from external power supply (included)

[11] - Mic Output Jack Used for connection to a DVR with multiple audio inputs or to a

soundcard module for audio recording. May also be used for

paralleling to a second Louroe audio base station.

MICROPHONE CONNECTIONS TO AP-8

A 12Vdc power supply is included with the above units. First connect the small end with the 90° plug to the above

units DC Jack[11] and connect large end to a standard 120Vac outlet or power strip.

Maximum distance between AP-8, etc. and Louroe microphones is 1,000 ft. (305m)

CONNECTING AP-8 TO A RECORDING DEVICE (DVR, ETC.)

All Louroe Verifact™ Microphones contain a 3-pin terminal block marked A, B, C. All Louroe base stations contain similar

3-pin terminal blocks marked A, B, C. Refer to interconnection diagram p 5.

A = 12Vdc Power (red wire)

B = Audio Output (black wire)

C = Common Ground (bare wire)

1) Take one end of recommended cable to first microphone location and connect:

Red wire to terminal A (12Vdc)

Black wire to terminal B (Audio Output)

Bare wire to terminal C (Ground)

2) Run other end of cable to the AP-8 Base Station location and connect to the 3-pin terminal block of the audio

zone in which the remote microphone is assigned (example zone 1). Again connect Red wire to Pin A, Black

wire to Pin B and Bare wire to Pin C.

3) Repeat the same procedure for the remaining microphones using the additional terminal blocks marked zone

2, zone 3, etc.

A) If connecting to a VCR or to a DVR with one audio input:

1) Connect an RCA cable to the Audio Out jack [9] of AP-8 and connect other end to Audio In (or line in)

of VCR/DVR

2) To record, press the Zone Selector Switch [1] located on front panel of base station for the audio zone

to be recorded

3) For audio playback, connect another RCA cable from Audio Out (or line out) of VCR/DVR to Audio In

[8] of AP-8

4) Press in the Play/Mute Switch[1] of front panel

5) Press the play or playback button on VCR/DVR to start audio playback. Playback will be broadcast

through the base station’s built-in speaker. As an alternate playback may be channeled through a

CCTV monitor with amplifier or through DVR’s speaker system

2) If connecting to a DVR with multiple audio inputs or to a soundcard module:

AP-4 has 4 line level RCA Mic Output Jacks [11]

1) Connect RCA cables between the Mic Output Jacks [11] and Audio Inputs of DVR

2) For audio playback from base station (AP-8), press in the Play/Mute Switch[1] located on base

station’s front panel. Playback may also be channeled through other audio sources

3) To select a specific audio zone for playback, refer to DVR’s instruction manual

APPLYING POWER TO THE AP-8

INSTALLATION AND OPERATING INSTRUCTIONS

Page 4 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

INSTALLATION AND OPERATING INSTRUCTIONS

Page 5 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

INTERCONNECTION DIAGRAM FOR VERIFACT A MICROPHONE

AND AP-8 BASE STATION

ABC

AA BCC

A A BC C

AA BC C

12345678

IN OUT

A B C

CBA

Red(A)

Black(B)

Bare(C)

Red(A)

Black(B) Bare(C)

Red(A)

Black(B)

Bare(C)

12Vdc

SELECTABLE

AUDIO OUTPUT

Use if recording device

has only one Audio Input

Use for audio playback

from recording device

WIRING REQUIREMENTS

VERIFACT A MICROPHONE

(CONNECTIONS ARE SIMILAR TO AP-2 AND AP-4)

REAR OF AP-8 BASE STATION

2 Cond Shielded Cable

22 Gauge with a 24 Gauge

Drain wire.

SUMMARY

Please check that wiring and power connections conform to the above instructions. In the event of a malfunction, refer to

the troubleshooting guide, next page. Should the problem persist, factory assistance is available from 8:00 AM to 4:00

PM (Pacific Time) by calling (818) 994-6498.

OPERATION AND TEST

After microphones and power supply are connected, proceed as follows:

1) Turn on power to the unit by rotating the Power-Volume Knob[5] clockwise to “ON” position. The Power

Indicator LED [4] will illuminate, indicating power to the unit. Rotate Power-Volume Knob[5] further

clockwise to increase the volume of monitored audio.

2) Press Zone Selector Switch[2] marked zone 1. Audio from zone 1 should be present at the Monitor

Speaker[7]. The Zone Selector Switch[2] is lighted indicating audio for that zone is present. If there is no

audio, remove wires connected to Mic Input 3-Pin Terminal Block[6] for zone 1 at the rear of the unit. With a

DC voltmeter, check that 12 Vdc is present at terminals “A” and “C”. If voltage is not present, unit has a

problem with its power supply. If voltage is present, check to assure that wires are connected properly to the

right terminals. Otherwise microphone is defective. Call factory for assistance.

3) Repeat step 2 for the remainder of the zones.

4) When a recorder is connected to the unit, press Play/Mute Switch[1]. Switch lights up indicating unit is in

playback or mute mode. Start recording live audio. The Play/Mute Switch[1] must be depressed or in the

“OUT” position when a recorder is not connected to the unit.

5) Playback recorded audio through the AP-4, etc. built-in amplifier and speaker.

6) The Play/Mute Switch[1] can be used to mute the audio heard on the speaker. The orange light is On when

this switch is engaged. This function doesn’t mute the audio going to the DVR.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 6 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

ask4_108_inst_9/13

TROUBLESHOOTING

II. No audio present.

a. Using a DC Voltmeter, check the voltage across terminal “A” and “C” (”A” positive; “C” ground) of the Mic 3-Pin

Terminal Block[12]. It should read 12V. The microphone requires 12Vdc to work.

1) Check connections to the microphone.

b. Remove the wire connected to the “B” terminal of the Mic 3-Pin Terminal Block. Using an AC meter (set to

lowest voltage range), check the presence of audio from the microphone. Place the meter leads between wire

removed (positive) and terminal “C” (ground). Generate some loud noise close to the remote microphone

while observing the meter reading. If audio is present, the meter reading will start to fluctuate. If there is no

movement, the remote microphone is defective. Call factory for assistance.

Factory assistance is available between 8:30 AM to 4:00 PM Pacific time. Call (818) 994-6498.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 7 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

SPECIFICATIONS - Verifact™ A

Frequency response

Output

Current drain

40 Hz to 15 kHz ± 1 dB

4 mA

Supply voltage 12 Vdc

Microphone housing High impact ABS

Dimensions US

Weight

4” "dia x 1 ½ H

(10cm dia x 3.8cm H)

0.5 Lb (0.2 Kg)

Line Level (0 dB @ 1000W)

metric

ask4_108_inst_9/13

SPECIFICATIONS (APSeries)

Input impedance

(from remote mic)

100KW

Monitor power output 1W @ 8

Audio input impedance 10k

Freq. response 100 Hz to 10kHz

Power input 12 Vdc, 500mA

Dimensions 6 5/8"W x 8 5/8 x 2 1/8"H"L

Headphone impedance

Current Drain

8 to 600

200mA

Weight 1lb 12oz

Audio output impedance 1KW

Power Input Frequency 50 / 60 Hz

MANUFACTURED

IN THE

IMPORTANT NOTICE

When this equipment is used as part of an

audio monitoring system, the law requires

that the public be given notice of AUDIO

MONITORING ON THE PREMISES. A

decal notice is included with each

microphone shipped.

Federal Law References:

Federal Regulations, US Code, Title 18.

Crime and Criminal Procedure, Sec 2510.

Page 8 of 8

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

WARRANTY

LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.

Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.

This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .

This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation

instructions provided by LOUROE ELECTRONICS.

Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.

AUDIO

MONITORING

These Premises

ask4_108_inst_9/13

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Louroe Electronics Sistema di altoparlanti

Louroe Electronics

Louroe Electronics ASK-4 101C Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 101-DV Istruzioni operative

Louroe Electronics

Louroe Electronics Verifact DVGC Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 304-DV Manuale utente

Louroe Electronics

Louroe Electronics APR-1 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 101 Manuale utente

Louroe Electronics

Louroe Electronics LE-019 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 300 Manuale utente

Louroe Electronics

Louroe Electronics verifact agc Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 601 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 122 Manuale utente

Louroe Electronics

Louroe Electronics LE-363 Manuale utente

Louroe Electronics

Louroe Electronics VERIFACT L-DT Manuale utente

Louroe Electronics

Louroe Electronics Verifact A USB Manuale utente

Louroe Electronics

Louroe Electronics AP-1TB Manuale utente

Louroe Electronics

Louroe Electronics AP-2TB Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 Guida utente

Louroe Electronics

Louroe Electronics LE-018 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 104 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 102 Manuale utente

Louroe Electronics

Louroe Electronics LE-393 Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 300 Manuale di servizio

Louroe Electronics

Louroe Electronics AP-4TB-RM Manuale utente

Louroe Electronics

Louroe Electronics ASK-4 # 304 Manuale utente

Manuali Sistema di altoparlanti popolari di altre marche

JVC

JVC CA-MXK5R Manuale utente

LG NB4532B Manuale utente

JVC

JVC CA-FSH100 Manuale utente

5Core

5Core Pro Series Manuale utente

EAW

EAW MQV1394e Manuale utente

Lynx

Lynx GXR-LA10A Manuale utente

iLive

iLive ITB066B Manuale utente

RDX

RDX QuickStation 4 Manuale utente

Electro-Voice

Electro-Voice S-122 Manuale utente

Sven

Sven SPS-619 GOLD Manuale utente

Pioneer

Pioneer CS-7070 Manuale utente

EAW

EAW UB82e Manuale utente

Sondpex

Sondpex Active Speaker System and Digital Music... Manuale utente

JVC

JVC NX-PN7 Manuale utente

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuale utente

Yamaha

Yamaha NX-A01 - Speaker Sys Manuale utente

SE Audiotechnik

SE Audiotechnik I-LINE Manuale utente

Gemini

Gemini WRX-843 Series Manuale utente