Low Range Off-Road SER-THC Manuale utente
Suggested Tools:
•Standard Screwdriver
•12 mm Combination Wrench
CAUTION: Safety glasses should be
worn at all times when working with
vehicles and related tools and
equipment.
Suzuki Samurai 1.3L Replacement Throttle Cable
(SKU# SER-THC)
Installation Instructions
For additional copies of these
and other instructions go to:
www.lowrangeoffroad and click on the
“Instructions” tab.
Instructions Created by an:
Step 2
Loosen the lock nut on the throttle cable
using 12mm open end wrench.
Step 1
Locate the throttle cable bracket which
is connected to the carburetor which is
inboard from the air cleaner assembly.
Step 4
Remove the cable from the bracket.
Step 3
Continue loosening the lock nut until the
cable can be removed from the bracket.
Step 5
Once the cable is free from the bracket,
reach down and disconnect the cable
from the carburetor throttle linkage.
(See greater detail in the next 3 Tech
Tips)
Tech Tip 5A
Make as much slack in the cable as
possible.
Tech Tip 5B
Align the cable with the slot in the
linkage.
Tech Tip 5C
Pull the cable end out of the linkage.
Notice: The carburetor shown in Tech
Tips 5A to 5C is off the vehicle and
laying on its side. This is done to give a
clearer view of how to disconnect the
cable from the carburetor.
Step 7
Position the NEW throttle cable in the
same place that the OLD one was.
Note: Do not connect to the bracket yet.
Step 6
Pull the OLD throttle cable away from
the carburetor and lay it aside for now.
Step 9
Place the NEW throttle cable in the
bracket with the nuts left loose for now.
Step 8
Reconnect the NEW throttle cable to the
linkage by reversing the removal
procedure shown in Tech Tips 5A to 5C.
Step 11
Pull the NEW throttle cable around
behind the engine and lay it aside for
now.
Note: Be sure the NEW cable is routed
in the exact same path as the OLD
cable.
Step 10
Route the other end of the NEW throttle
cable in the same path as the old cable.
Step 13
Using a standard screwdriver, push the
cable out of the hole in the bulkhead.
Step 12
From inside the passenger compartment,
pull slack in the old cable at the point
where the cable passes through the
bulkhead (or firewall) and disconnect it
from the accelerator pedal linkage.
Note: The procedure for disconnecting
the cable from the accelerator pedal is
similar to the way you disconnected the
cable from the carburetor.
Step 15
Completely remove the OLD cable and
set it aside.
Step 14
Pull the OLD cable out of the bulkhead
into the engine compartment.
Step 16
Push the NEW cable through the
bulkhead and snap it into place.
Note: Be sure the NEW cable is routed
in the same path as the OLD cable.
Step 17
Go back to the carburetor and
disconnect the NEW throttle cable from
the bracket.
Note: This will give you enough slack to
make the connection at the accelerator
pedal.
Step 19
Reconnect the throttle linkage to the
bracket at the carburetor.
Step 18
Connect the new cable to the
accelerator linkage in reverse order of
removal.
Step 21
Tighten the lock nut using a 12mm open
end wrench.
Step 20
Tighten the lock nut as tight as you can
with your finger.
Step 22
Check the cable for proper “Cable Play”
adjustment. (See next step)
Step 23
Using the illustration shown above
check the amount of “cable play”.
Compare your findings to the chart
shown above. If the cable play is not
within specification it will need to be
adjusted. Follow the instructions listed
below:
•If the cable play is to great, loosen the
lock nut and turn the adjusting nut
clockwise. Then tighten the lock nut.
•If cable play is to small, loosen the
lock nut and turn the adjusting nut
counter clockwise. Then retighten the
lock nut.
Continue the adjustment procedure until
the correct cable play is obtained.
Congratulations!
You have successfully installed the
throttle cable. We hope these
instructions have been helpful. If
you have suggestions on how to
improve these instructions (or
products), please email us at:
Step 24
Check the execrator pedal. It should
move freely through the entire pedal
travel. If there is binding or excessive
resistance, check that there are no
kinks in the cable and that it is routed
without sharp bends. Reroute or
repair as needed.
As always, If you experience any difficulty during the installation of this product
please contact Low Range Off-Road Technical Support at 801-805-6644 M-F
during regular store hours. Thank you for purchasing from Low Range Off-Road.
These instructions are designed as a general installation guide. Installation of many Low Range
Off-Road products require specialized skills such as metal fabrication, welding and mechanical
trouble shooting. If you have any questions or are unsure about how to proceed, please contact
our shop at 801-805-6644 or seek help from a competent fabricator. Using fabrication tools such
as welders, torches and grinders can cause serious bodily harm and death. Please operate
equipment carefully and observe proper safety procedures.
Rock crawling and off-road driving are inherently dangerous activities. Some modifications will
adversely affect the on-road handling characteristics of your vehicle. All products sold by Low
Range Off-Road are sold for off road use only. Any other use or application is the responsibility
of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may
under certain circumstances void your original dealer warranty. Modification of your vehicle may
create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or
death. Buyers and users of these products hereby expressly assume all risks associated with any
such modifications and use.
Revised 11/19/14© Copyright 2014 Low Range Off-Road, LC!!!!!! All Rights Reserved
Altri manuali Low Range Off-Road Accessori per motociclette
