LSIS XGL-CH2A Manuale utente

Right choice for ultimate yield

LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.

Programmable Logic Controller

Cnet I/F Module

User’s Manual



Read this manual carefully before

installing,

wiring, operating, servicing

or inspecting this equipment.



Keep this manual within easy reach

for quick reference.

XGL-

CH2A

XGL-

C22A

XGL-C24A

XGT Series

http://eng.lsis.biz

Safety Instructions

Before using the product …

For your safety and effective operation, please read the safety instructions

thoroughly before using the product.

►Safety Instructions should always be observed in order to prevent accident

or risk with the safe and proper use the product.

►Instructions are divided into “Warning” and “Caution”, and the meaning of

the terms is as follows.

This symbol indicates the possibility of serious injury

or death if some applicable instruction is violated

This symbol indicates the possibility of severe or

slight injury, and property damages if some

applicable instruction is violated

Moreover, even classified events under its caution category may develop into

serious accidents relying on situations. Therefore we strongly advise users to

observe all precautions properly just like warnings.

►The marks displayed on the product and in the user’s manual have the

following meanings.

Be careful! Danger may be expected.

Be careful! Electric shock may occur.

►The user’s manual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instructions

Safety Instructions for design process

Please install a protection circuit on the exterior of PLC so that the

whole system may operate safely regardless of failures from

external power or PLC. Any abnormal output or operation from PLC

may cause serious problems to safety in whole system.

- Install protection units on the exterior of PLC like an interlock circuit

that deals with opposite operations such as

emergency stop,

protection circuit, and forward/reverse rotation or install an interlock

circuit that deals with high/low limit under its position controls.

- If any system error (watch-dog timer error, module installation error,

etc.) is detected during CPU operation in PLC, all output signals are

designed to be turned off and stopped for safety. However, there

are cases when output signals remain active due to device failures

in Relay and TR which can’t be detected

. Thus, you are

recommended to install an addition circuit to monitor the output

status for those critical outputs which may cause significant

problems.

Never overload more than rated current of output module nor

allow to have a short circuit. Over current for a long period time may

cause a fire .

Never let the external power of the output circuit to be on earlier

than PLC power, which may cause accidents from abnormal output or

operation.



Please install interlock circuits in the sequence program for safe

operations in the system when exchange data with PLC or modify

operation modes using a

computer or other external equipments

Read specific instructions thoroughly when conducting control

operations with PLC.

Warning

Safety Instructions

Safety Instructions for design process

Safety Instructions on installation process

I/O signal or communication line shall be wired at least 100mm

away from a high-voltage cable or power line.Fail to follow this

instruction may cause malfunctions from noise

Caution

Use PLC only in the environment specified in PLC manual or

general standard of data sheet. If not, electric shock, fire, abnormal

operation of the product may be caused.

Before install or remove the module, be sure PLC power is off. If

not, electric shock or damage on the product may be caused.

Be sure that every module is securely attached after adding a

module or an extension connector.

If the product is installed

loosely or incorrectly, abnormal operation, error or dropping may be

caused. In addition, contact failures under poor cable installation will

be causing malfunctions as well.

Be sure that screws get tighten securely under vibrating

environments.

Fail to do so will put the product under direct

vibrations which will cause electric shock, fire and abnormal

operation.

Do not come in contact with conducting parts in each module,

which may cause electric shock, malfunctions or abnormal operation.

Caution

Safety Instructions

Safety Instructions for wiring process

Prior to wiring works, make sure that every power is turned off. If

not, electric shock or damage on the product may be caused.



After wiring process is done, make sure that terminal covers are

installed properly before its use.Fail to install the cover may cause

electric shocks.

Warning

Check rated voltages and terminal arrangements in each product

prior to its wiring process.

Applying incorrect voltages other than

rated voltages and misarrangement among terminals may cause fire

or malfunctions.

Secure terminal screws tightly applying with specified torque.If

the screws get loose, short circuit, fire or abnormal operation may be

caused. Securing screws too tightly will cause damages to the module

or malfunctions, short circuit, and dropping.

Be sure to earth to the ground using Class 3 wires

for FG

terminals which is exclusively used for PLC. If the terminals not

grounded correctly, abnormal operation or electric shock

may be

caused.

Don’t let any foreign materials such as wiring waste inside the

module while wiring, which may cause fire, damage on the product

or abnormal operation.

Make sure that pressed terminals

get tighten following the

specified torque. External connector type shall be pressed or

soldered using proper equipments.

Caution

Safety Instructions

Safety Instructions for test-operation and

maintenance

Don’t touch the terminal when powered. Electric shock or abnormal

operation may occur.

Prior to cleaning or tightening the terminal screws, let all the

external power off including PLC power.

If not, electric shock or

abnormal operation may occur.

Don’t let the battery recharged, disassembled, heated, short or

soldered. Heat, explosion or ignition may cause injuries or fire.

Warning

Do not make modifications or disassemble each module.Fire,

electric shock or abnormal operation may occur.

Prior to installing or disassemb

ling the module, let all the

external power off including PLC power.

If not, electric shock or

abnormal operation may occur.

Keep any wireless equipment such as walkie-talkie or cell phones

at least 30cm away from PLC.

If not, abnormal operation may be

caused.

When making a modification on programs or using run to modify

functions under PLC operations,

read and comprehend all

contents in the manual fully. Mismanagement will cause damages to

products and accidents.

Avoid any physical impact to the battery and prevent it from

dropping as well.

Damages to battery may cause leakage from its

fluid. When battery was dropped or exposed under strong impact,

never reuse the battery again. Moreover skilled workers are needed

when exchanging batteries.

Caution

Safety Instructions

Safety Instructions for waste disposal

Product or battery waste shall be processed as industrial waste.

The waste may discharge toxic materials or explode itself.

Caution

Revision History

Version

Data

Remark

Page

V 1.0 ’05.03 First Edition -

V1.1 ’05.05.19 Add function description -

V1.2 ’05.19.12 Change available CPU device address -

V2.0 ’07.01.15 Change XG-PD description

V 2.1 ’08.02

1. Adding contents

(1) Production Configuration

(2) Software to use the product

(3) Operation Sequence

(4) I/O assignment and Device Information

(5) General of Communication Parameter

(6) Transmission Standard

(7) How to set transmission Standard

(8) Menu bar and shortcut of XG-PD

(9) Operation Start

(10) Diagnosis Function of XG-PD

<Ch.7 XGT Dedicated Communication>

(11) Summary of Protocol

(12) Frame Structure

(13) XGT Communication Function

(14) Remote Connection

(15) Modem Communication

(16) Communication Command

<Ch.8 Modbus Communication>

(17) General

(18) Modbus Protocol

(19) Structure of Frame

(20) Modbus Server

(21) Modbus RTU/ASCII Client

(22) Frame Monitor

<Ch.9 User-defined Communication>

(23) General

(24) Structure of user definition frame

(25) Frame Monitor

(26) Trouble shooting

1-3

1-4 ~ 1-5

4-3

4-6 ~ 4-13

6-1

6-2

6-25

6-27 ~ 6-28

6-35 ~ 6-37

6-42 ~ 6-48

7-1 ~ 7-47

8-1 ~ 8-31

9-1 ~ 9-11

11-9 ~ 11-11

Revision History

Version Data Remark Page

(27) User interface using Visual Basic

(28) Dimension

(29) Index

2. Fixing the contents

(1) Introduction

(2) Characteristics

(3) Performance Specifications

(4) Designation of Parts

(5) Cable Specifications

(6) Terminal Resistance

(7) Channel Operation during Normal Run

(8) Method of Serial Interface

(9) P2P setting parameter

(10) Available System Configurations

(11) Unavailable System Configurations

(12) Communication Module Registration

(13) Safety Instructions

A-18 ~ A-29

A-30

A-31 ~ A-32

1-1

1-2

2-2

2-3

2-4

2-5

3-2

3-4

4-5

5-1~ 5-6

5-7 ~ 5-8

6-20 ~ 6-24

V2.2

’08.07

1. Head office address change

Back cover

2. Adding contents

(1) How to configure XGR basic system

4-8

(2) Available device area per CPU

4-12

3. Fixing the contents

(1) Introduction

1-1,1-3

(2) Product Specification

2-3

(3) Installation and Test Operation

4-4, 4-9

(4) Communication Parameter

6-1, 6-47

(5) XGT dedicated communication

7-3, 7-5

(6) Modbus communication

8-18, 8-24

(7) User defined communication

9-3

(8) Example program

10-7

(9) Diagnosis

11-4

(10) Standard setting window modification

Entire

V2.3

’10.03

1. Characteristics modified

Ch1.2

2. CPU added

Ch1.3.2

3. Content on the remote connection modified

Ch7.4.2

4. Figure and figure number of modem

communication modified

Ch7.5

Revision History

V2.4 ’10.06.17 1. 2.1 Change general specification

2. 3.4.1 (2) Change Null modem connection cable

3. Back address change and delete

2-1

3-4

Back cover

V2.5

’11.05

1. How to enable link through flag added

CH6.7.2

V2.6 ’14.01.10 1. Change typographical error

2. Delete XGR main base module description

3. Change RS-485 communication cable direction

4. Not usable system configuration

5. add parity bit Ignore function

6. Change delay time setting typographical error

7. Change direct variable write typographical error

8. Change Modbus RTU typographical error

9. add UDATA instruction description

10. Add example UDATA function

Entire

CH1.3.2, CH2.2,

CH4.5.1

CH3.4.2

CH5.2.1

CH6.1.1, CH6.2.1

CH6.1.1

CH7.2.3

CH8

CH9.5

CH10.6

V2.7 ’14.04.19 Change system configuration Entire

V2.8

’14.11

XG5000 V4.0 UI Updated

Entire

※The number of User’s manual is indicated right part of the back cover.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali LSIS Controllori

LSIS

LSIS XBF-AD04A Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGL-EFMT Manuale utente

LSIS

LSIS XEC-DN32U Manuale utente

LSIS

LSIS LSLV-S100 Series Manuale utente

LSIS

LSIS XP10BKA/DC Manuale utente

LSIS

LSIS XBC-DR20SU Manuale utente

LSIS

LSIS XBC-DN32U Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XEC-DN32H/DC Manuale utente

LSIS

LSIS XBM-DN16S Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS Master-K K200S Manuale utente

LSIS

LSIS XDL-L7NH Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS S100 Series Manuale di programmazione

LSIS

LSIS SV-iS7 series Manuale utente

LSIS

LSIS sv-ip5a Manuale utente

LSIS

LSIS XDL-L7SA002X Manuale utente

LSIS

LSIS XGT Series Manuale utente

LSIS

LSIS XGT Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

3M MicroTouch EX113 Manuale utente