LUCCI Air MONZA Manuale utente

v1.0-AU (05/2023)

LUCCI AIR

MONZA

IP55 DC CEILING FAN

⚫INSTALLATION

⚫OPERATION

⚫MAINTENANCE

⚫WARRANTY INFORMATION

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION.

MONZA IP55 DC Fan Installation Instructions

1 | P a g e

THANK YOU FOR PURCHASING

Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power

which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and

silent operation.

Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to

65% more energy than ceiling fans with traditional AC motors.

Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor

noise.

Low operating temperature – The DC power is managed effectively which brings down the motor operating

temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the

longevity of the motor.

6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes

complete with a 6 speed remote, which gives a greater choice of comfort levels.

SAFETY PRECAUTIONS

1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.

3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring

rules.

WARNING:

FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION

MUST BE INCORPORATED INTO THE FIXED WIRING IN

ACCORDANCE WITH THE WIRING RULES.

As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum

electrical safety of this standard.

Please note warranty will be void if installation is without a means for an

all-pole disconnection incorporated in the fixed wiring in accordance with

the wiring rules.

MONZA IP55 DC Fan Installation Instructions

2 | P a g e

Example: If a fan is connected to a circuit that can be isolated via an all-

pole safety switch at the switchboard, then this is considered to be an

all-pole disconnection to the ceiling fan electrical circuit, meeting the

requirements of clause 7.12.2 of AS/NZS 60335.1.

A single-pole switch on the active of the receiver input of remote

control must also be included in the wiring, and located the same

room as the ceiling fan.

4. Do not dispose of electrical appliances, remote or batteries as unsorted municipal waste, use

separate collection facilities. Contact your local government for information regarding the collection

systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances

can leak into the ground water and get into the food chain, damaging your health and well-being. Please

contact your local council or regional authority for more information on collection, reuse, and recycling

programmes.

5. The structure to which the fan is to be mounted must be capable of supporting a weight of 24 kg.

6. The fan should be mounted so that the blades are more than 2.1 m above the floor.

7. This fan is suitable for indoor, alfresco, and coastal areas. This product is IP55 rated and can be exposed

to jets of water from any direction. This rating should be maintained during installation.

8. Must be assembled and installed by a licensed electrician.

9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling

fan and contact the manufacturer, its service agent or suitably qualified persons.

10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,

its service agent or suitably qualified persons.

11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a

sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension

system shall be performed by the manufacturer, its service agent or suitably qualified persons.

12. This remote contains battery that is non-replaceable.

13. The remote control can only be powered at a safe extra low voltage (DC 5 V).

MONZA IP55 DC Fan Installation Instructions

3 | P a g e

PARTS LIST

•Unpack your ceiling fan carefully. Remove all parts and hardware.

•Lay out all the components on a smooth surface and make sure there are no components missing before

assembling. If parts are missing, return the complete product to the place of purchase for inspection or

replacement.

•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product

which appears damaged in any way. Return the complete product to the place of purchase for inspection,

repair or replacement.

•Examine all parts, you should have the following:

Blades x 5

Mounting screws x 2

Mounting bracket x 1

Balancing kit x 1

Canopy bracket x 1

Blade screws x 16

Canopy cover & Canopy x 1 set

Receiver x 1

Downrod and Ball Joint x 1

Remote controller x1

Fan assembly x 1

Fig. 1

MONZA IP55 DC Fan Installation Instructions

4 | P a g e

INSTALLING THE FAN

TOOLS REQUIRED:

- Phillips / flat head screwdriver

- Pair of pliers

- Adjustable spanner

- Step ladder

- Wire cutter

- Wiring, supply cable as required by local provincial and national wiring codes and regulations.

INSTALLING THE MOUNTING BRACKET

•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the

blade to the nearest objects or walls.

•Remove the canopy cover from the canopy by anticlockwise. (Fig. 2)

•Attach the mounting bracket to the canopy cover.

•Secure the hanging bracket with the canopy cover to the ceiling joist or structure that is capable of carrying

a load of at least 24kg, with two long screws provided. Ensure at least 30mm of the screw is threaded

into the support. (Fig. 3)

NOTE: The bracket screws provided are for use with wooden structures only. For structures other

than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the

mounting surface and the surrounding environment.

Fig. 2

Fig. 3

MONZA IP55 DC Fan Installation Instructions

5 | P a g e

ANGLED CEILING INSTALLATION

The hanging system of this fan is ONLY suitable for flat ceiling installation.

DO NOT install the fan on an angled ceiling.

INSTALLING THE DOWN ROD (Fig. 4)

1. Remove the ball joint (4) and dowel pin (3) by loosening the set screws (5) from the down rod (6).

Remove the hitch pin (2) by removing the lock clip (1) (Fig. 4.1). NOTE: Do not discard keep these

parts, they are required to reassemble later.

2. Remove the decorative cover (7) from the fan assembly by turning anticlockwise. (Fig. 4.2)

Fig. 4.1

Fig. 4.2

MONZA IP55 DC Fan Installation Instructions

6 | P a g e

3. Loosen the set screws (8) on the down rod coupling housing (9). (Fig. 4.3)

3. Carefully feed the fan wires up through the down rod (6). (fig. 4.4)

4. Assemble the down rod (6) into the down rod coupling housing (9), by inserting and line up the down rod

coupling housing holes with the down rod holes and insert the hitch pin (2) and secure with the lock clip (1).

(Fig. 4.4)

5. Secure the down rod (6) by tightening the set screws (8). (Fig. 4.4)

Fig. 4.3

Fig. 4.4

MONZA IP55 DC Fan Installation Instructions

7 | P a g e

6. Insert the decorative cover (7) onto the down rod (6) to cover the down rod coupling housing (9).

Finally install the decorative cover (7) onto the fan assembly (10), secure it by turning it clockwise. (Fig. 4.5)

7.Insert the canopy (12) & canopy bracket (11) over the down rod (6) and install the ball joint (4) and dowel

pin (3) back onto the down rod (6) and secure by tightening the set screws (5). (Fig. 4.6& Fig.4.7)

Fig. 4.5

Fig. 4.6

Fig. 4.7

MONZA IP55 DC Fan Installation Instructions

8 | P a g e

HANGING THE FAN

Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on

the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig. 5)

ELECTRICAL WIRING DIAGRAM THE FAN

PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (FIG. 6)

WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A

LICENSED ELECTRICIAN.

NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED

WIRING.

NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN

ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN

PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.

NOTE: Ensure the motor earth wire is connected to the single earthing terminal block “1” from

mounting bracket in the diagram below (Fig. 6).

From mains supply to mounting bracket terminal block: (Fig. 6)

1. Connect the live supply wire to the “L” terminal of the terminal block on the mounting bracket.

2. Connect the neutral supply wire to “N” terminal of the terminal block on the mounting bracket.

3. Connect earth wire to the earth terminal of the terminal block on the mounting bracket.

From mounting bracket to receiver and motor: (Fig. 6)

4. Connect the supply wiring from the mounting bracket to the input of the DC motor receiver.

5. Connect the output wires of DC motor receiver to the input wires of the fan motor.

6. Connect the earth wire of fan motor to the single earthing terminal block “1” from mounting bracket in the

diagram below.

Fig. 5

MONZA IP55 DC Fan Installation Instructions

9 | P a g e

Carefully insert the receiver above the hanger ball in the remainder spacing in the mounting bracket. Take

care not to damage or loosen any of the wiring. (Fig. 7).

Fig. 7

Fig. 6

Indice

Altri manuali LUCCI Air Fan

LUCCI Air

LUCCI Air ARRAY Manuale utente

LUCCI Air

LUCCI Air AIRFUSION HAVANA Manuale utente

LUCCI Air

LUCCI Air ABYSS IP66 Manuale utente

LUCCI Air

LUCCI Air ESPERANCE Series Manuale utente

LUCCI Air

LUCCI Air AIRFUSION UNIONE-56 ORB Manuale utente

LUCCI Air

LUCCI Air AIRFUSION ZOOM Guida all'installazione

LUCCI Air

LUCCI Air Airfusion Newport Manuale utente

LUCCI Air

LUCCI Air AIRFUSION FLUSSO Manuale utente

LUCCI Air

LUCCI Air AIRFUSION BREEZE Guida all'installazione

LUCCI Air

LUCCI Air AIRFUSION A Manuale utente

LUCCI Air

LUCCI Air AIRFUSION CLIMATE III Guida all'installazione

LUCCI Air

LUCCI Air AIRFUSION PEREGRINE Guida all'installazione

LUCCI Air

LUCCI Air GRENADA Series Manuale utente

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Guida all'installazione

LUCCI Air

LUCCI Air Nordic Manuale utente

LUCCI Air

LUCCI Air AERO Series Manuale del proprietario

LUCCI Air

LUCCI Air OSPREY 216170 Manuale del proprietario

LUCCI Air

LUCCI Air AIRFUSION MARINER Manuale utente

LUCCI Air

LUCCI Air AIRFUSION AKMANI Guida all'installazione

LUCCI Air

LUCCI Air AIRFUSION QUEST II Manuale utente

LUCCI Air

LUCCI Air CLIMATE III Manuale utente

LUCCI Air

LUCCI Air Aria CTC Manuale utente

LUCCI Air

LUCCI Air AIRFUSION SHOALHAVEN Guida all'installazione

LUCCI Air

LUCCI Air AIRFUSION GIRONA Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio